SPL

Premium DAC with VOLTAiR technologyDiamond is the perfect DAC and preamplifier for everyone who plays music exclusively from digital sources. Diamond offers connectivity for six digital sources and an external word clock. The superior VOLTAiR technology and the premium DAC with the unequalled DLP120 combined with an analog volume control allowing for highest resolution at any volume makes the Diamond an one-of-a-kind DA converter that delivers finest soundstages with an unrivalled analog feel.Everything under controlThe volume is adjusted with a solid, milled aluminum, rotary knob. The Alps RK27 “Big Blue” potentiometer gives a pleasant “spoon in the honey” rotary feel.Source of joyUp to 6 digital stereo sources can be connected to Diamond.Diamond offers each a stereo USB and AES input as well as each two optical and coaxial stereo inputs. Via USB, both PCM audio and DSD audio can be converted. PCM audio is received in S/PDIF format, both coaxial (RCA), optical (Toslink F06) and balanced (AES/EBU). The source selection is done via the selection control on the front. The selected input is also shown in the dot matrix LED display: USB, COA1, COA2, OPT1, OPT2 or AES. After approximately two seconds, the display shows the type of clock source and the detected sampling rate.Always in timeDiamond can not only synchronize to the clock integrated in the digitally fed source signal. As a specialist for digital players Diamond offers a word clock input. The source of the clock signal can be selected via the CLOCK switch.Source = Diamond synchronizes to the digital clock in the source signal.Word = Diamond synchronizes to the digital clock present at WORD IN.Well informedThe DAC automatically picks up the sampling rate and resolution of the digital playback source. No matter if a streamer, computer, CD player or an external word clock is connected. The detected sampling rate and the selected clock source are shown in the dot matrix LED display. For example, U768 is an acronym for a clock signal in the USB stream with a sampling rate of 768 kHz.All variable – or Slave ThruDiamond provides two stereo output pairs for connecting power amplifiers or active loudspeakers. One pair of outputs with XLR, the other with RCA outputs. Both have the same output signal, which is controlled by the volume control on the front panel. The volume control for both outputs can be individually switched out of the signal path via DIP switch on the back of the device. For example, a headphone amplifier with its own volume control can be connected to one of the outputs.The DAC768The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the digital-to-analogue converter, which thanks to its architecture reproduces the finest sound details.It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768 kHz, which is equivalent to 16 times CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. In contrast to the DAC 768xs, the DAC768 not only offers an AES/EBU digital input, but also the SPL DLP120 with VOLTAiR technology.The DLP120 (Dual Low-Pass)The analog output of the DAC chip must be filtered by a low pass filter. Phonitor xe has two of them: One for PCM audio and one for DSD audio, since different roll-off frequencies are required.In contrast to all other DACs in the world, the low pass filters here are built using VOLTAiR technology, which provides a plus in dynamics and headroom and sound.Sounds goodWith all devices of the Professional Fidelity series we develop not only according to plan, but also by ear. Many important components are installed on the circuit boards using Through-hole technology. This way we can ensure that we can use the best sounding components.The VOLTAiR TechnologyThe 120V technology is our reference technology. The 120V technology is unique in the world. It operates at a DC voltage of 120 volts. This is four times that of IC-based semiconductor op-amps. In our Professional Fidelity series, we refer to this unsurpassed technology as VOLTAiR technology.The highest possible audio quality requires the highest possible audio operating voltageThe 120V technology works with +/-60 V. To be able to handle such a high voltage, we have developed special proprietary operational amplifiers that can operate with a DC voltage of +/-60 V: the SPL 120V SUPRA operational amplifiers. This high voltage would destroy conventional components and operational amplifiers.The 120V technology achieves exceptional technical specifications and sonic benefits. Technically, in terms of dynamic range, signal-to-noise ratio and headroom. Sonically, in terms of richness of detail and an absolutely relaxed listening experience. By the way, the “120V” in the name of the technology has nothing to do with the local mains voltage from the mains power socket. This is about the operating voltage inside the device with which the audio signals are processed.The mains voltage from the mains power socket is transformed to the required secondary voltage in the device’s internal linear power supply with toroidal transformer. Rectifiers convert this AC voltage into DC voltage required in the audio device.VOLTAiR is a composition of the terms Volt and Air. Volt is the unit for electrical voltage and Air stands for the unlimited space the music can breathe in. It symbolizes the perceived limitless dynamics resulting from high audio voltage.ComparisonMost audio devices work with an internal operating voltage of +/-15 volts and can thus process a maximum input level of +21.5 dBu. If a DAC, for example, has an output level of +22 dBu at 0 dBFS, level peaks of the music material would already cause overloads in the input stage of the device. All components in the audio device often operate at their limits. The result is an unsteady sound that causes stress and faster ear fatigue.SPL devices with VOLTAiR technology can handle input levels of +32.5 dBu thanks to the higher internal operating voltage of +/- 60 volts – thus offering 12 dB more headroom. All components consequently operate continuously in the optimum operating range. The result is a very pleasant, natural and relaxed sound experience. So you can enjoy your music in every detail.

Premium DAC with VOLTAiR technologyDiamond is the perfect DAC and preamplifier for everyone who plays music exclusively from digital sources. Diamond offers connectivity for six digital sources and an external word clock. The superior VOLTAiR technology and the premium DAC with the unequalled DLP120 combined with an analog volume control allowing for highest resolution at any volume makes the Diamond an one-of-a-kind DA converter that delivers finest soundstages with an unrivalled analog feel.Everything under controlThe volume is adjusted with a solid, milled aluminum, rotary knob. The Alps RK27 “Big Blue” potentiometer gives a pleasant “spoon in the honey” rotary feel.Source of joyUp to 6 digital stereo sources can be connected to Diamond.Diamond offers each a stereo USB and AES input as well as each two optical and coaxial stereo inputs. Via USB, both PCM audio and DSD audio can be converted. PCM audio is received in S/PDIF format, both coaxial (RCA), optical (Toslink F06) and balanced (AES/EBU). The source selection is done via the selection control on the front. The selected input is also shown in the dot matrix LED display: USB, COA1, COA2, OPT1, OPT2 or AES. After approximately two seconds, the display shows the type of clock source and the detected sampling rate.Always in timeDiamond can not only synchronize to the clock integrated in the digitally fed source signal. As a specialist for digital players Diamond offers a word clock input. The source of the clock signal can be selected via the CLOCK switch.Source = Diamond synchronizes to the digital clock in the source signal.Word = Diamond synchronizes to the digital clock present at WORD IN.Well informedThe DAC automatically picks up the sampling rate and resolution of the digital playback source. No matter if a streamer, computer, CD player or an external word clock is connected. The detected sampling rate and the selected clock source are shown in the dot matrix LED display. For example, U768 is an acronym for a clock signal in the USB stream with a sampling rate of 768 kHz.All variable – or Slave ThruDiamond provides two stereo output pairs for connecting power amplifiers or active loudspeakers. One pair of outputs with XLR, the other with RCA outputs. Both have the same output signal, which is controlled by the volume control on the front panel. The volume control for both outputs can be individually switched out of the signal path via DIP switch on the back of the device. For example, a headphone amplifier with its own volume control can be connected to one of the outputs.The DAC768The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the digital-to-analogue converter, which thanks to its architecture reproduces the finest sound details.It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768 kHz, which is equivalent to 16 times CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. In contrast to the DAC 768xs, the DAC768 not only offers an AES/EBU digital input, but also the SPL DLP120 with VOLTAiR technology.The DLP120 (Dual Low-Pass)The analog output of the DAC chip must be filtered by a low pass filter. Phonitor xe has two of them: One for PCM audio and one for DSD audio, since different roll-off frequencies are required.In contrast to all other DACs in the world, the low pass filters here are built using VOLTAiR technology, which provides a plus in dynamics and headroom and sound.Sounds goodWith all devices of the Professional Fidelity series we develop not only according to plan, but also by ear. Many important components are installed on the circuit boards using Through-hole technology. This way we can ensure that we can use the best sounding components.The VOLTAiR TechnologyThe 120V technology is our reference technology. The 120V technology is unique in the world. It operates at a DC voltage of 120 volts. This is four times that of IC-based semiconductor op-amps. In our Professional Fidelity series, we refer to this unsurpassed technology as VOLTAiR technology.The highest possible audio quality requires the highest possible audio operating voltageThe 120V technology works with +/-60 V. To be able to handle such a high voltage, we have developed special proprietary operational amplifiers that can operate with a DC voltage of +/-60 V: the SPL 120V SUPRA operational amplifiers. This high voltage would destroy conventional components and operational amplifiers.The 120V technology achieves exceptional technical specifications and sonic benefits. Technically, in terms of dynamic range, signal-to-noise ratio and headroom. Sonically, in terms of richness of detail and an absolutely relaxed listening experience. By the way, the “120V” in the name of the technology has nothing to do with the local mains voltage from the mains power socket. This is about the operating voltage inside the device with which the audio signals are processed.The mains voltage from the mains power socket is transformed to the required secondary voltage in the device’s internal linear power supply with toroidal transformer. Rectifiers convert this AC voltage into DC voltage required in the audio device.VOLTAiR is a composition of the terms Volt and Air. Volt is the unit for electrical voltage and Air stands for the unlimited space the music can breathe in. It symbolizes the perceived limitless dynamics resulting from high audio voltage.ComparisonMost audio devices work with an internal operating voltage of +/-15 volts and can thus process a maximum input level of +21.5 dBu. If a DAC, for example, has an output level of +22 dBu at 0 dBFS, level peaks of the music material would already cause overloads in the input stage of the device. All components in the audio device often operate at their limits. The result is an unsteady sound that causes stress and faster ear fatigue.SPL devices with VOLTAiR technology can handle input levels of +32.5 dBu thanks to the higher internal operating voltage of +/- 60 volts – thus offering 12 dB more headroom. All components consequently operate continuously in the optimum operating range. The result is a very pleasant, natural and relaxed sound experience. So you can enjoy your music in every detail.

Premium DAC with VOLTAiR technologyDiamond is the perfect DAC and preamplifier for everyone who plays music exclusively from digital sources. Diamond offers connectivity for six digital sources and an external word clock. The superior VOLTAiR technology and the premium DAC with the unequalled DLP120 combined with an analog volume control allowing for highest resolution at any volume makes the Diamond an one-of-a-kind DA converter that delivers finest soundstages with an unrivalled analog feel.Everything under controlThe volume is adjusted with a solid, milled aluminum, rotary knob. The Alps RK27 “Big Blue” potentiometer gives a pleasant “spoon in the honey” rotary feel.Source of joyUp to 6 digital stereo sources can be connected to Diamond.Diamond offers each a stereo USB and AES input as well as each two optical and coaxial stereo inputs. Via USB, both PCM audio and DSD audio can be converted. PCM audio is received in S/PDIF format, both coaxial (RCA), optical (Toslink F06) and balanced (AES/EBU). The source selection is done via the selection control on the front. The selected input is also shown in the dot matrix LED display: USB, COA1, COA2, OPT1, OPT2 or AES. After approximately two seconds, the display shows the type of clock source and the detected sampling rate.Always in timeDiamond can not only synchronize to the clock integrated in the digitally fed source signal. As a specialist for digital players Diamond offers a word clock input. The source of the clock signal can be selected via the CLOCK switch.Source = Diamond synchronizes to the digital clock in the source signal.Word = Diamond synchronizes to the digital clock present at WORD IN.Well informedThe DAC automatically picks up the sampling rate and resolution of the digital playback source. No matter if a streamer, computer, CD player or an external word clock is connected. The detected sampling rate and the selected clock source are shown in the dot matrix LED display. For example, U768 is an acronym for a clock signal in the USB stream with a sampling rate of 768 kHz.All variable – or Slave ThruDiamond provides two stereo output pairs for connecting power amplifiers or active loudspeakers. One pair of outputs with XLR, the other with RCA outputs. Both have the same output signal, which is controlled by the volume control on the front panel. The volume control for both outputs can be individually switched out of the signal path via DIP switch on the back of the device. For example, a headphone amplifier with its own volume control can be connected to one of the outputs.The DAC768The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the digital-to-analogue converter, which thanks to its architecture reproduces the finest sound details.It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768 kHz, which is equivalent to 16 times CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. In contrast to the DAC 768xs, the DAC768 not only offers an AES/EBU digital input, but also the SPL DLP120 with VOLTAiR technology.The DLP120 (Dual Low-Pass)The analog output of the DAC chip must be filtered by a low pass filter. Phonitor xe has two of them: One for PCM audio and one for DSD audio, since different roll-off frequencies are required.In contrast to all other DACs in the world, the low pass filters here are built using VOLTAiR technology, which provides a plus in dynamics and headroom and sound.Sounds goodWith all devices of the Professional Fidelity series we develop not only according to plan, but also by ear. Many important components are installed on the circuit boards using Through-hole technology. This way we can ensure that we can use the best sounding components.The VOLTAiR TechnologyThe 120V technology is our reference technology. The 120V technology is unique in the world. It operates at a DC voltage of 120 volts. This is four times that of IC-based semiconductor op-amps. In our Professional Fidelity series, we refer to this unsurpassed technology as VOLTAiR technology.The highest possible audio quality requires the highest possible audio operating voltageThe 120V technology works with +/-60 V. To be able to handle such a high voltage, we have developed special proprietary operational amplifiers that can operate with a DC voltage of +/-60 V: the SPL 120V SUPRA operational amplifiers. This high voltage would destroy conventional components and operational amplifiers.The 120V technology achieves exceptional technical specifications and sonic benefits. Technically, in terms of dynamic range, signal-to-noise ratio and headroom. Sonically, in terms of richness of detail and an absolutely relaxed listening experience. By the way, the “120V” in the name of the technology has nothing to do with the local mains voltage from the mains power socket. This is about the operating voltage inside the device with which the audio signals are processed.The mains voltage from the mains power socket is transformed to the required secondary voltage in the device’s internal linear power supply with toroidal transformer. Rectifiers convert this AC voltage into DC voltage required in the audio device.VOLTAiR is a composition of the terms Volt and Air. Volt is the unit for electrical voltage and Air stands for the unlimited space the music can breathe in. It symbolizes the perceived limitless dynamics resulting from high audio voltage.ComparisonMost audio devices work with an internal operating voltage of +/-15 volts and can thus process a maximum input level of +21.5 dBu. If a DAC, for example, has an output level of +22 dBu at 0 dBFS, level peaks of the music material would already cause overloads in the input stage of the device. All components in the audio device often operate at their limits. The result is an unsteady sound that causes stress and faster ear fatigue.SPL devices with VOLTAiR technology can handle input levels of +32.5 dBu thanks to the higher internal operating voltage of +/- 60 volts – thus offering 12 dB more headroom. All components consequently operate continuously in the optimum operating range. The result is a very pleasant, natural and relaxed sound experience. So you can enjoy your music in every detail.

The headphone amplifier, monitoring controller and DAC with 120V technology Phonitor 3 DAC is not only the ultimate headphone amplifier and monitoring controller with 120V technology – the integrated DAC makes it the perfect monitoring centerpiece for demanding producers as well as sound and mastering engineers working with digital sources or in the DAW. Whether if USB, AES/EBU or S/PDIF – the integrated DAC with analog SLP120 converts digital PCM audio signals with a resolution of 32 bit and a sampling rate of up to 768 kHz. It converts DSD signals with a resolution of up to DSD256. On the analog side, the Phonitor 3 DAC, based on the SPL 120V technology, offers the same monitoring quality as the big SPL mastering consoles – on loudspeakers and headphones. The analog Phonitor Matrix allows mixing and mastering on headphones in the highest quality – with the same spatial perception of the stereo stage as on loudspeakers.Great sound – for headphonesThe Phonitor 3 DAC offers connection for a standard headphone with a stereo jack plug on the front. Thanks to the enormous output power, all kind of headphones are driven effortlessly. Thus, it plays out the advantages of the SPL 120V technology and rewards the listener with an honest, detailed and at the same time vivid sound experience.Great sound – also for loudspeakersOn the rear of the device, Phonitor 3 DAC offers a stereo output which makes it a high-quality monitoring controller for any monitoring situation. Active speakers with an integrated power amplifier or passive speakers in combination with a power amplifier can be connected at this output.Monitoring at the highest levelPhonitor 3 DAC offers the same key technology – SPL 120V technology – and signal quality as the big SPL DMC and MMC mastering consoles.Headphones or SpeakersThe Output switch – simply switch from headphone to speaker playback. In the center position (Mute), no signal reaches the outputs. The VU meters light up red.Digital & analog stereo inputs – free choiceUp to six stereo sources can be connected to the Phonitor 3 DAC. The source is selected via the Source switch.Analog inputsOn the analog side, two analog stereo inputs are offered, each with two XLR line inputs. Professional analog players with balanced outputs and line level can be connected here.Digital inputsOn the digital side, the Phonitor 3 DAC offers four digital stereo inputs.USBThe USB input (type B) can be used to directly connect the DAW. No driver installation is required for operation with a Mac or an iDevice. Via USB, the Phonitor 3 DAC converts PCM audio signals with a resolution of 32 bits and a sampling rate of up to 768 kHz as well as DSD signals with a resolution of up to DSD256.S/PDIF, coaxialThe Input S/PDIF coaxial can also receive a two-channel signal (PCM audio) with sampling rates up to 192 kHz and a bit rate of 16 bits to 24 bits. Unbalanced, 2-wire 75-ohm coaxial cables with RCA connectors are used for signal transmission.S/PDIF, opticalThe S/PDIF optical input can also receive a two-channel signal (PCM audio) with sampling rates of up to 192 kHz and a bit rate of 16 bit to 24 bit. The input jack is an F05 jack. This interface is better known under the Toshiba brand name TOSLINK.Tip: You should attach importance to the quality of the optical fiber. With inexpensive plastic optical fibers, transmissions with quad sampling rates (176.4kHz/192kHz) may have faults. In this case a glass fiber optic cable should be chosen.AES/EBUThe AES input provides an input jack which corresponds to a standard XLR input (XLR, female). An AES signal can transport two encoded PCM audio channels with a maximum sampling rate of 192 kHz and a bit rate of 16 bits to 24 bits. This standard is defined under IEC 60958 Type I. Balanced, 3-core, 110 Ohm “twisted pair” cables with XLR plugs are used for connection.The DAC – the best is just good enoughThe converter chip in the Phonitor 3 DAC´s digital-to-analog converter is the highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip, which thanks to its architecture reproduces the finest sound details. It converts PCM audio at 32-bit resolution and a sampling rate of up to 768 kHz, which is 16 times the resolution of a CD. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256.SLP120The analog output of any DAC chip must be filtered by a low pass filter when entering the analog world. In contrast to all other DACs in the world, the low pass filters here are built using SPL 120V technology, which provides a plus in dynamics and headroom and sound. The DAC in the Phonitor 3 DAC is equipped with the SLP120 – an analog “single low pass” filter with 120V technology.Milled from solidThe massive 45mm volume control knob milled from aluminum is a haptic highlight. Its mass together with the Alps RK27 “Big Blue” potentiometer enhances the “spoon in the honey” feeling even further and provides perfect control of the monitoring level.Monitoring without any compromisesThe Phonitor 3 DAC is a full-fledged monitor controller:Source selectionPhonitor Matrix with Crossfeed, Speaker Angle and Center Level (the latter can be switched off)Mono/StereoLaterality controlSolo L/RPhase inversion for L and RL/R SwapOutput switchable to headphones or speakersMuteMono or stereo – a matter of settingThe Mono/Stereo switch can be used to select whether the output signal of the Phonitor 3 DAC is a regular stereo signal or whether it is summed to a mono signal.Finding the real centerNaturally, hearing can be directed more to the left or more to the right. This becomes particularly clear when listening on headphones. Therefore, the Phonitor 3 DAC has the uniquely finely resolved laterality control, which rebalances the stereo image on the monitoring side. The Mono/Stereo switch can not only be used to switch between stereo or mono playback. This switch is also used to activate or deactivate the laterality control.Solo L/ROnly the right or left channel of the audio signal should be played back? The Solo L/R function makes it possible. If the triple selection switch is in the “L” position, only the left channel is played back – if it is in the “R” position, only the right channel is played back. In the middle position “Off” the Solo function is switched off. The regular stereo signal consisting of the left and right channel is thus present at the output of the Phonitor 3 DAC.L/R SwapA special feature is the channel swap function: L/R Swap. This function inverts the stereo image. Left becomes right and right becomes left. This is especially important and extremely time-saving, when you are monitoring samples in video dubbing that should match a scene with direction of movement. If the direction is not correct, you usually have to load the sample into the DAW to switch channels. before you can judge whether the sample matches the image. With the L/R Swap function, this is no longer necessary. You can now adjust the direction of movement on the Phonitor 3 DAC while pre-listening the sample library.Phase inversion for L and RWith this switch the phase of the left or right channel of the audio signal can be inverted. If the three-way selection switch is in the “L” position, the left channel is inverted – if it is in the “R” position, the right channel is inverted. In the middle position “Off” this function is switched off. At the output of the Phonitor 3 DAC the regular stereo signal is thus present.M/S – Mid or Side?By using the mono/stereo and L/R phase inversion switch in combination, it is also possible to only monitor the mid or side signal. When the switch is set to “Mono” and phase inversion is active for L (or R), only the side signal is played back. If the phase inversion is switched off, the mono signal corresponding to the “M” signal is played back. Separate monitoring of the M and S signals has become a widespread standard for many mixing and mastering engineers.Everything at a glanceTwo mechanical VU meters visualize the input levels for the left and right audio channels. The “VU Cal” switch can be used to reduce the signal visualized on the VU meters by -6 dB or -12 dB. Thus, the VU meters operate in the ideal display range even at very high input levels.The Revolution: Phonitor MatrixThe Phonitor Matrix is the revolution in the headphone amplifier.One of the unique features of SPL headphone amplifiers is the SPL Phonitor Matrix. It enables mixing and mastering engineers to create perfect mixes on headphones, which will translate perfectly to all types of stereo speaker systems. But the Phonitor Matrix is not only designed for professional use in the studio. It also enables the hifi enthusiast to enjoy music on headphones, like if it was played back on speakers.How is this possible?Music is normally produced and mixed for playback on stereo speakers. Listening on headphones is different from listening on loudspeakers. The biggest difference is the lack of crossing signals of the sound signal from the left speaker to the right ear and from the right speaker to the left ear.These crossing signals are missing in conventional headphone listening, because there are no signals crossing from one side of the headphones to the other. This results in an unnaturally wide stereo stage and sound sources are not played back at their actual position in the stereo spectrum. The SPL Phonitor Matrix can correct this false stereo image with an analog circuitry.Summed up:The SPL Phonitor Matrix corrects the false representation of the stereo sound image, which makes it much easier to find the right decisions for mixing and mastering engineers. The hifi enthusiast can experience the music, like it was originally mixed and recorded. So nothing stands in the way of a successful and long mixing session on headphones.Preamp Out or Direct OutWith a DIP switch on the rear of the device, the volume control for the rear stereo output can be switched out of the signal path. But that’s not all. It is also possible to output the Phonitor Matrix to the stereo output on the rear panel of the device – regardless of whether this is configured as Preamp Out (with volume control) or Direct Out (without volume control).More powerIf headphones have a rather low sensivity – no problem. With DIP switch 1 on the rear of the device, the level at the headphone output can be increased by 12 dB.Sounds goodWith all SPL devices we develop not only according to plan, but also by ear. All important components are installed on the circuit boards using Through-hole technology. This way we can ensure that we can use the best sounding components.The 120V technologyThe 120V technology is our reference technology. The 120V technology is unique in the world. It operates at a DC voltage of 120 volts. This is four times that of IC-based semiconductor op-amps.

Το Phonitor x, είναι ο απόλυτος ενισχυτής ακουστικών. Προσφέρει συνδέσεις για ακουστικά τόσο balanced όσο και unbalanced, ενώ με ισχύ εξόδου 3.7 W, η απόδοσή του είναι εντυπωσιακή. Στην έκδοση με το νέο DAC768xs module, the Phonitor x δείχνει τις μοναδικές του δυνατότητες σαν ενισχυτής ακουστικών αλλά και σαν προενισχυτής. Το επαναστατικό σύστημα Phonitor Matrix, προσφέρει την πιό ρεαλιστική ακρόαση για ακουστικά, αφού δημιουργεί την εντύπωση ακρόασης μέσω ηχείων. Το Phonitor x, δεν είναι μόνο ενισχυτής ακουστικών, αλλά και ένας εξαιρετικός προενισχυτής, όπου μπορείτε να συνδέσετε έναν τελικό ενισχυτή ή ενεργά ηχεία μόνιτορ Προδιαγραφές: Ενισχυτής ακουστικών και προενισχυτής, τεχνολογίας VOLTAiR 120 V Rail,  Ξεχωριστές συνδέσεις για ακουστικά και τελικό ενισχυτή balanced και unbalanced,  Κατάλληλο για όλα τα ακουστικά με αντίσταση μεγαλύτερη από 10 ohms,  Είσοδοι balanced και unbalanced (XLR και RCA),  Προαιρετικά ψηφιακές εισόδους: USB, coaxial and optical,  Προαιρετικά μετατροπέας DAC: 192 kHz / 24 Bit,  Έξοδοι balanced και unbalanced (XLR και RCA),  Phonitor Matrix για προσομοίωση ακρόασης ηχείων,  Έλεγχος Laterality: super-fine balance,  Διακόπτης Mono,  Έλεγχος στάθμης (ελέγχεται και με τηλεχειριστήριο),  Μέγιστη ισχύς εξόδου: 2 x 3.7 W (120 ohms),  Απόκριση συχνότητας: 10 Hz - 300 kHz (-3 dB),  THD+N: 0.00091 % (HP), 0.00085 % (Line),  Dynamic range: 135.5 dB (HP), 136.3 dB (Line),  Σύνδεση AMP CTR με τον τελικό ενισχυτή Performer (για έλεγχο του διακόπτη on/off),  Made in Germany Χαρακτηριστικά: Απόκριση Συχνότητας: ‹10Hz - ›200kHz (-3dB) Αριθμός Εισόδων: 2 Αριθμός Εξόδων: 2 & 1(Headphones) Δυναμική Περιοχή: 129,5 dBΑ Ενισχυτής Ακουστικών: ΝΑΙ Συνδετήρες Εισόδου: 2 x XLR Συνδετήρες Εξόδου: 2 x XLR 1 x TRS Τύπος Ενίσχυσης: Ενεργή  

Με καινοτόμο Phonitor Matrix, μετατροπέα DA 32-bit και εξαιρετική ποιότητα ήχου. Για εμάς ο ήχος είναι πάντα σε πρώτο πλάνο και για να αποκτήσετε έναν τέτοιο ήχο, χρειάζεστε εμπειρία και τεχνική φινέτσα. Έχουμε ενσωματώσει και τα δύο στη σειρά Phonitor One. Το στάδιο του προενισχυτή Δύο ενισχυτές Burr-Brown OPA 2134 SoundPlus™ παρέχουν την προενίσχυση. Αυτά είναι ειδικά σχεδιασμένα για κυκλώματα audiophile και χαρακτηρίζονται από εξαιρετικά χαμηλό θόρυβο και ελάχιστη παραμόρφωση μόνο 0,00008%. Χάρη σε ένα πραγματικό στάδιο FET, το OPA 2134 επιτυγχάνει ρυθμό περιστροφής 20 V/μs, καθιστώντας το έναν λειτουργικό ενισχυτή υψηλής ταχύτητας. Αυτό έχει άμεσα θετική επίδραση στη ζωντάνια της αναπαραγωγής. Επιπλέον, πυκνωτές φιλμ χαμηλής χωρητικότητας εγκαθίστανται στη διαδρομή σήματος ως πυκνωτές παράκαμψης των πυκνωτών ζεύξης, γεγονός που εξασφαλίζει ακριβέστερη μετάδοση των στοιχείων του σήματος υψηλής συχνότητας. Οι εξαιρετικοί ηλεκτρολυτικοί πυκνωτές Panasonic «Electric Double Layer» χρησιμοποιούνται ως πυκνωτές σύζευξης. Προσφέρουν την υψηλότερη χωρητικότητα αποθήκευσης από όλες τις τεχνολογίες πυκνωτών.

Our nonplusultra headphone amplifier.The Phonitor xe is the nonplusultra standalone headphone amplifier without any compromises. Phonitor Matrix, remote volume control, retro-look VU meter, the optional premium DA converter and the all-superior VOLTAiR technology make the Phonitor xe one of the best headphone amplifiers of our time.Great Sound – for all headphonesThe Phonitor xe offers connections for a standard headphone with a stereo jack plug and for balanced-driven headphones using a 4 pin XLR plug.Thanks to the enormous output power, all headphones are driven effortlessly.Thus, it plays out the advantages of the SPL VOLTAiR technology and rewards the listener with an honest, detailed and at the same time vivid sound experience.Twice as niceThe Phonitor xe provides headphone outputs on the front and on the rear. On the front, you switch between F (front) and R (rear). This way, your favorite headphones remain firmly connected on the rear – without visible cabling on the front.Milled from solidThe massive 45mm volume control knob milled from aluminum is a haptic highlight. Its mass together with the motorized Alps RK27 “Big Blue” potentiometer enhances the “spoon in the honey” feeling even further.The red marker LED ensures good visibility of the volume parameter even in darkened environments.Remote controlThe volume control can be remotely controlled with any infrared remote control.The Phonitor xe learns to communicate with it with the simple push of a button.Learning made easyUsing Phonitor x as an example, this video explains how you can use any infrared remote control to remotely control the volume.Source of joyUp to six (6 !) stereo sources can be connected to the Phonitor xe:XLR, RCA and via the optional DAC768 also USB, COAX, OPTICAL and AES.Phonitor xe accepts almost all audio connections. Balanced via XLR or unbalanced via RCA connectors.With the optional DAC768, four additional digital sources are added. From USB to professional AES format, no wishes remain unfulfilled.The DAC automatically picks up the sampling rate and resolution of the digital playback source. No matter if a streamer, computer or CD player is connected. No further settings on the Phonitor xe are necessary.The DAC768The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the optional digital-to-analogue converter, which thanks to its architecture reproduces the finest sound details.It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768 kHz, which is equivalent to 16 times CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. In contrast to the DAC 768xs, the DAC768 not only offers an AES/EBU digital input, but also the SPL DLP120 with VOLTAiR technology.The DLP120 (Dual Low-Pass)The analog output of the DAC chip must be filtered by a low pass filter. Phonitor xe has two of them: One for PCM audio and one for DSD audio, since different roll-off frequencies are required.In contrast to all other DACs in the world, the low pass filters here are built using VOLTAiR technology, which provides a plus in dynamics and headroom and sound.Good ol' timesTwo mechanical VU meters visualize the input levels for the left and right audio channel.With the VU switch you can optimize the display for different signal levels.Finding the middleis not always easy. By our very nature, hearing can be leaning more to the left or more to the right. This is especially obvious when listening with headphones.That’s why Phonitor xe has the uniquely finely resolved laterality control. With it, the center can be found perfectly.With the MODE switch you can choose between stereo or mono playback. This switch also activates the laterality control.The Revolution: Phonitor MatrixThe Phonitor Matrix is the revolution in the headphone amplifier.Thanks to the Phonitor Matrix, music can be experienced on headphones as if it was played on speakers. The tiring super stereo effect is a thing of the past.Enjoy your music without listening fatigue and exactly the way it should be heard.Music is normally produced and mixed for playback on stereo speakers.Listening on headphones is different from listening on loudspeakers. The biggest difference is the lack of crossing signals of the sound signal from the left speaker to the right ear and from the right speaker to the left ear. These crossing signals are missing in conventional headphone listening, because there are no signals crossing from one side of the headphones to the other. This results in an unnaturally wide stereo image and the various sound sources of the audio signal are not localized as the sound engineer intended them to. This effect is often referred to as “super stereo effect”. During conventional listening on headphones, our brain can balance the false representation of the playback to a certain extent – but this is very exhausting.The SPL Phonitor Matrix can correct this false stereo image with an analog circuitry. The Phonitor Matrix therefore not only ensures a correct representation of the stereo image, but also a relaxed listening experience.The two main parameters of the Phonitor Matrix are Crossfeed and Angle:Crossfeed determines the crossing signals of the channels, the so-called interaural level difference.Angle determines the opening angle of the stereo image, the so-called interaural time difference.Center of AttentionTo make the listening experience even more perfect, the level of the center of the stereo image needs to be attenuated when the Phonitor Matrix is active. This ensures that not only the position of all sound sources is correct but also their volume.In the Professional Fidelity Phonitor devices this value is set to a fixed attenuation of -1 dB, which is the best choice for getting an authentic representation of the sound stage.Sounds good!With all devices of the Professional Fidelity series we develop not only according to plan, but also by ear. All important components are installed on the circuit boards using Through-hole technology. This way we can ensure that we can use the best sounding components.The VOLTAiR TechnologyThe 120V technology is our reference technology. The 120V technology is unique in the world. It operates at a DC voltage of 120 volts. This is four times that of IC-based semiconductor op-amps. In our Professional Fidelity series, we refer to this unsurpassed technology as VOLTAiR technology.The highest possible audio quality requires the highest possible audio operating voltage.The 120V technology works with +/-60 V. To be able to handle such a high voltage, we have developed special proprietary operational amplifiers that can operate with a DC voltage of +/-60 V: the SPL 120V SUPRA operational amplifiers. This high voltage would destroy conventional components and operational amplifiers.By the way, the “120V” in the name of the technology has nothing to do with the local mains voltage from the mains power socket. This is about the operating voltage inside the device with which the audio signals are processed.The mains voltage from the mains power socket is transformed to the required secondary voltage in the device’s internal linear power supply with toroidal transformer. Rectifiers convert this AC voltage into DC voltage required in the audio device.

Our nonplusultra headphone amplifier.The Phonitor xe is the nonplusultra standalone headphone amplifier without any compromises. Phonitor Matrix, remote volume control, retro-look VU meter, the optional premium DA converter and the all-superior VOLTAiR technology make the Phonitor xe one of the best headphone amplifiers of our time.Great Sound – for all headphonesThe Phonitor xe offers connections for a standard headphone with a stereo jack plug and for balanced-driven headphones using a 4 pin XLR plug.Thanks to the enormous output power, all headphones are driven effortlessly.Thus, it plays out the advantages of the SPL VOLTAiR technology and rewards the listener with an honest, detailed and at the same time vivid sound experience.Twice as niceThe Phonitor xe provides headphone outputs on the front and on the rear. On the front, you switch between F (front) and R (rear). This way, your favorite headphones remain firmly connected on the rear – without visible cabling on the front.Milled from solidThe massive 45mm volume control knob milled from aluminum is a haptic highlight. Its mass together with the motorized Alps RK27 “Big Blue” potentiometer enhances the “spoon in the honey” feeling even further.The red marker LED ensures good visibility of the volume parameter even in darkened environments.Remote controlThe volume control can be remotely controlled with any infrared remote control.The Phonitor xe learns to communicate with it with the simple push of a button.Learning made easyUsing Phonitor x as an example, this video explains how you can use any infrared remote control to remotely control the volume.Source of joyUp to six (6 !) stereo sources can be connected to the Phonitor xe:XLR, RCA and via the optional DAC768 also USB, COAX, OPTICAL and AES.Phonitor xe accepts almost all audio connections. Balanced via XLR or unbalanced via RCA connectors.With the optional DAC768, four additional digital sources are added. From USB to professional AES format, no wishes remain unfulfilled.The DAC automatically picks up the sampling rate and resolution of the digital playback source. No matter if a streamer, computer or CD player is connected. No further settings on the Phonitor xe are necessary.The DAC768The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the optional digital-to-analogue converter, which thanks to its architecture reproduces the finest sound details.It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768 kHz, which is equivalent to 16 times CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. In contrast to the DAC 768xs, the DAC768 not only offers an AES/EBU digital input, but also the SPL DLP120 with VOLTAiR technology.The DLP120 (Dual Low-Pass)The analog output of the DAC chip must be filtered by a low pass filter. Phonitor xe has two of them: One for PCM audio and one for DSD audio, since different roll-off frequencies are required.In contrast to all other DACs in the world, the low pass filters here are built using VOLTAiR technology, which provides a plus in dynamics and headroom and sound.Good ol' timesTwo mechanical VU meters visualize the input levels for the left and right audio channel.With the VU switch you can optimize the display for different signal levels.Finding the middleis not always easy. By our very nature, hearing can be leaning more to the left or more to the right. This is especially obvious when listening with headphones.That’s why Phonitor xe has the uniquely finely resolved laterality control. With it, the center can be found perfectly.With the MODE switch you can choose between stereo or mono playback. This switch also activates the laterality control.The Revolution: Phonitor MatrixThe Phonitor Matrix is the revolution in the headphone amplifier.Thanks to the Phonitor Matrix, music can be experienced on headphones as if it was played on speakers. The tiring super stereo effect is a thing of the past.Enjoy your music without listening fatigue and exactly the way it should be heard.Music is normally produced and mixed for playback on stereo speakers.Listening on headphones is different from listening on loudspeakers. The biggest difference is the lack of crossing signals of the sound signal from the left speaker to the right ear and from the right speaker to the left ear. These crossing signals are missing in conventional headphone listening, because there are no signals crossing from one side of the headphones to the other. This results in an unnaturally wide stereo image and the various sound sources of the audio signal are not localized as the sound engineer intended them to. This effect is often referred to as “super stereo effect”. During conventional listening on headphones, our brain can balance the false representation of the playback to a certain extent – but this is very exhausting.The SPL Phonitor Matrix can correct this false stereo image with an analog circuitry. The Phonitor Matrix therefore not only ensures a correct representation of the stereo image, but also a relaxed listening experience.The two main parameters of the Phonitor Matrix are Crossfeed and Angle:Crossfeed determines the crossing signals of the channels, the so-called interaural level difference.Angle determines the opening angle of the stereo image, the so-called interaural time difference.Center of AttentionTo make the listening experience even more perfect, the level of the center of the stereo image needs to be attenuated when the Phonitor Matrix is active. This ensures that not only the position of all sound sources is correct but also their volume.In the Professional Fidelity Phonitor devices this value is set to a fixed attenuation of -1 dB, which is the best choice for getting an authentic representation of the sound stage.Sounds good!With all devices of the Professional Fidelity series we develop not only according to plan, but also by ear. All important components are installed on the circuit boards using Through-hole technology. This way we can ensure that we can use the best sounding components.The VOLTAiR TechnologyThe 120V technology is our reference technology. The 120V technology is unique in the world. It operates at a DC voltage of 120 volts. This is four times that of IC-based semiconductor op-amps. In our Professional Fidelity series, we refer to this unsurpassed technology as VOLTAiR technology.The highest possible audio quality requires the highest possible audio operating voltage.The 120V technology works with +/-60 V. To be able to handle such a high voltage, we have developed special proprietary operational amplifiers that can operate with a DC voltage of +/-60 V: the SPL 120V SUPRA operational amplifiers. This high voltage would destroy conventional components and operational amplifiers.By the way, the “120V” in the name of the technology has nothing to do with the local mains voltage from the mains power socket. This is about the operating voltage inside the device with which the audio signals are processed.The mains voltage from the mains power socket is transformed to the required secondary voltage in the device’s internal linear power supply with toroidal transformer. Rectifiers convert this AC voltage into DC voltage required in the audio device.

Το Phonitor x, είναι ο απόλυτος ενισχυτής ακουστικών. Προσφέρει συνδέσεις για ακουστικά τόσο balanced όσο και unbalanced, ενώ με ισχύ εξόδου 3.7 W, η απόδοσή του είναι εντυπωσιακή.  Το επαναστατικό σύστημα Phonitor Matrix, προσφέρει την πιό ρεαλιστική ακρόαση για ακουστικά, αφού δημιουργεί την εντύπωση ακρόασης μέσω ηχείων. Το Phonitor x, δεν είναι μόνο ενισχυτής ακουστικών, αλλά και ένας εξαιρετικός προενισχυτής, όπου μπορείτε να συνδέσετε έναν τελικό ενισχυτή ή ενεργά ηχεία μόνιτορ Προδιαγραφές: Ενισχυτής ακουστικών και προενισχυτής, τεχνολογίας VOLTAiR 120 V Rail,  Ξεχωριστές συνδέσεις για ακουστικά και τελικό ενισχυτή balanced και unbalanced,  Κατάλληλο για όλα τα ακουστικά με αντίσταση μεγαλύτερη από 10 ohms,  Είσοδοι balanced και unbalanced (XLR και RCA),  Προαιρετικά ψηφιακές εισόδους: USB, coaxial and optical,  Προαιρετικά μετατροπέας DAC: 192 kHz / 24 Bit,  Έξοδοι balanced και unbalanced (XLR και RCA),  Phonitor Matrix για προσομοίωση ακρόασης ηχείων,  Έλεγχος Laterality: super-fine balance,  Διακόπτης Mono,  Έλεγχος στάθμης (ελέγχεται και με τηλεχειριστήριο),  Μέγιστη ισχύς εξόδου: 2 x 3.7 W (120 ohms),  Απόκριση συχνότητας: 10 Hz - 300 kHz (-3 dB),  THD+N: 0.00091 % (HP), 0.00085 % (Line),  Dynamic range: 135.5 dB (HP), 136.3 dB (Line),  Σύνδεση AMP CTR με τον τελικό ενισχυτή Performer (για έλεγχο του διακόπτη on/off),  Made in Germany Χαρακτηριστικά: Απόκριση Συχνότητας: ‹10Hz - ›200kHz (-3dB) Αριθμός Εισόδων: 2 Αριθμός Εξόδων: 2 & 1(Headphones) Δυναμική Περιοχή: 129,5 dBΑ Ενισχυτής Ακουστικών: ΝΑΙ Συνδετήρες Εισόδου: 2 x XLR Συνδετήρες Εξόδου: 2 x XLR 1 x TRS Τύπος Ενίσχυσης: Ενεργή  

Το Phonitor x, είναι ο απόλυτος ενισχυτής ακουστικών. Προσφέρει συνδέσεις για ακουστικά τόσο balanced όσο και unbalanced, ενώ με ισχύ εξόδου 3.7 W, η απόδοσή του είναι εντυπωσιακή.  Το επαναστατικό σύστημα Phonitor Matrix, προσφέρει την πιό ρεαλιστική ακρόαση για ακουστικά, αφού δημιουργεί την εντύπωση ακρόασης μέσω ηχείων. Το Phonitor x, δεν είναι μόνο ενισχυτής ακουστικών, αλλά και ένας εξαιρετικός προενισχυτής, όπου μπορείτε να συνδέσετε έναν τελικό ενισχυτή ή ενεργά ηχεία μόνιτορ Προδιαγραφές: Ενισχυτής ακουστικών και προενισχυτής, τεχνολογίας VOLTAiR 120 V Rail,  Ξεχωριστές συνδέσεις για ακουστικά και τελικό ενισχυτή balanced και unbalanced,  Κατάλληλο για όλα τα ακουστικά με αντίσταση μεγαλύτερη από 10 ohms,  Είσοδοι balanced και unbalanced (XLR και RCA),  Προαιρετικά ψηφιακές εισόδους: USB, coaxial and optical,  Προαιρετικά μετατροπέας DAC: 192 kHz / 24 Bit,  Έξοδοι balanced και unbalanced (XLR και RCA),  Phonitor Matrix για προσομοίωση ακρόασης ηχείων,  Έλεγχος Laterality: super-fine balance,  Διακόπτης Mono,  Έλεγχος στάθμης (ελέγχεται και με τηλεχειριστήριο),  Μέγιστη ισχύς εξόδου: 2 x 3.7 W (120 ohms),  Απόκριση συχνότητας: 10 Hz - 300 kHz (-3 dB),  THD+N: 0.00091 % (HP), 0.00085 % (Line),  Dynamic range: 135.5 dB (HP), 136.3 dB (Line),  Σύνδεση AMP CTR με τον τελικό ενισχυτή Performer (για έλεγχο του διακόπτη on/off),  Made in Germany Χαρακτηριστικά: Απόκριση Συχνότητας: ‹10Hz - ›200kHz (-3dB) Αριθμός Εισόδων: 2 Αριθμός Εξόδων: 2 & 1(Headphones) Δυναμική Περιοχή: 129,5 dBΑ Ενισχυτής Ακουστικών: ΝΑΙ Συνδετήρες Εισόδου: 2 x XLR Συνδετήρες Εξόδου: 2 x XLR 1 x TRS Τύπος Ενίσχυσης: Ενεργή  

Our nonplusultra headphone amplifier.The Phonitor xe is the nonplusultra standalone headphone amplifier without any compromises. Phonitor Matrix, remote volume control, retro-look VU meter, the optional premium DA converter and the all-superior VOLTAiR technology make the Phonitor xe one of the best headphone amplifiers of our time.Great Sound – for all headphonesThe Phonitor xe offers connections for a standard headphone with a stereo jack plug and for balanced-driven headphones using a 4 pin XLR plug.Thanks to the enormous output power, all headphones are driven effortlessly.Thus, it plays out the advantages of the SPL VOLTAiR technology and rewards the listener with an honest, detailed and at the same time vivid sound experience.Twice as niceThe Phonitor xe provides headphone outputs on the front and on the rear. On the front, you switch between F (front) and R (rear). This way, your favorite headphones remain firmly connected on the rear – without visible cabling on the front.Milled from solidThe massive 45mm volume control knob milled from aluminum is a haptic highlight. Its mass together with the motorized Alps RK27 “Big Blue” potentiometer enhances the “spoon in the honey” feeling even further.The red marker LED ensures good visibility of the volume parameter even in darkened environments.Remote controlThe volume control can be remotely controlled with any infrared remote control.The Phonitor xe learns to communicate with it with the simple push of a button.Learning made easyUsing Phonitor x as an example, this video explains how you can use any infrared remote control to remotely control the volume.Source of joyUp to six (6 !) stereo sources can be connected to the Phonitor xe:XLR, RCA and via the optional DAC768 also USB, COAX, OPTICAL and AES.Phonitor xe accepts almost all audio connections. Balanced via XLR or unbalanced via RCA connectors.With the optional DAC768, four additional digital sources are added. From USB to professional AES format, no wishes remain unfulfilled.The DAC automatically picks up the sampling rate and resolution of the digital playback source. No matter if a streamer, computer or CD player is connected. No further settings on the Phonitor xe are necessary.The DAC768The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the optional digital-to-analogue converter, which thanks to its architecture reproduces the finest sound details.It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768 kHz, which is equivalent to 16 times CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. In contrast to the DAC 768xs, the DAC768 not only offers an AES/EBU digital input, but also the SPL DLP120 with VOLTAiR technology.The DLP120 (Dual Low-Pass)The analog output of the DAC chip must be filtered by a low pass filter. Phonitor xe has two of them: One for PCM audio and one for DSD audio, since different roll-off frequencies are required.In contrast to all other DACs in the world, the low pass filters here are built using VOLTAiR technology, which provides a plus in dynamics and headroom and sound.Good ol' timesTwo mechanical VU meters visualize the input levels for the left and right audio channel.With the VU switch you can optimize the display for different signal levels.Finding the middleis not always easy. By our very nature, hearing can be leaning more to the left or more to the right. This is especially obvious when listening with headphones.That’s why Phonitor xe has the uniquely finely resolved laterality control. With it, the center can be found perfectly.With the MODE switch you can choose between stereo or mono playback. This switch also activates the laterality control.The Revolution: Phonitor MatrixThe Phonitor Matrix is the revolution in the headphone amplifier.Thanks to the Phonitor Matrix, music can be experienced on headphones as if it was played on speakers. The tiring super stereo effect is a thing of the past.Enjoy your music without listening fatigue and exactly the way it should be heard.Music is normally produced and mixed for playback on stereo speakers.Listening on headphones is different from listening on loudspeakers. The biggest difference is the lack of crossing signals of the sound signal from the left speaker to the right ear and from the right speaker to the left ear. These crossing signals are missing in conventional headphone listening, because there are no signals crossing from one side of the headphones to the other. This results in an unnaturally wide stereo image and the various sound sources of the audio signal are not localized as the sound engineer intended them to. This effect is often referred to as “super stereo effect”. During conventional listening on headphones, our brain can balance the false representation of the playback to a certain extent – but this is very exhausting.The SPL Phonitor Matrix can correct this false stereo image with an analog circuitry. The Phonitor Matrix therefore not only ensures a correct representation of the stereo image, but also a relaxed listening experience.The two main parameters of the Phonitor Matrix are Crossfeed and Angle:Crossfeed determines the crossing signals of the channels, the so-called interaural level difference.Angle determines the opening angle of the stereo image, the so-called interaural time difference.Center of AttentionTo make the listening experience even more perfect, the level of the center of the stereo image needs to be attenuated when the Phonitor Matrix is active. This ensures that not only the position of all sound sources is correct but also their volume.In the Professional Fidelity Phonitor devices this value is set to a fixed attenuation of -1 dB, which is the best choice for getting an authentic representation of the sound stage.Sounds good!With all devices of the Professional Fidelity series we develop not only according to plan, but also by ear. All important components are installed on the circuit boards using Through-hole technology. This way we can ensure that we can use the best sounding components.The VOLTAiR TechnologyThe 120V technology is our reference technology. The 120V technology is unique in the world. It operates at a DC voltage of 120 volts. This is four times that of IC-based semiconductor op-amps. In our Professional Fidelity series, we refer to this unsurpassed technology as VOLTAiR technology.The highest possible audio quality requires the highest possible audio operating voltage.The 120V technology works with +/-60 V. To be able to handle such a high voltage, we have developed special proprietary operational amplifiers that can operate with a DC voltage of +/-60 V: the SPL 120V SUPRA operational amplifiers. This high voltage would destroy conventional components and operational amplifiers.By the way, the “120V” in the name of the technology has nothing to do with the local mains voltage from the mains power socket. This is about the operating voltage inside the device with which the audio signals are processed.The mains voltage from the mains power socket is transformed to the required secondary voltage in the device’s internal linear power supply with toroidal transformer. Rectifiers convert this AC voltage into DC voltage required in the audio device.

The director sets the tone. The central unit of the HiFi system is the preamplifier. With remote source selection and volume control, retro-look-VU-meter, premium DA-converter and the all superior VOLTAiR technology, the Director Mk2 caters for musical blockbusters. Milled from solid is the big 45mm Volume control. Its mass together with the  motorized Alps RK27 “Big Blue” potentiometer enhances the “spoon in the honey” feeling even further. The red marker LED makes the setting visible even in darkened environments. Volume RC The volume can be remote controlled with any infrared remote control, that the Director Mk2 simply learns. Learning made easy This video explains how you can use any infrared remote control to remotely control the volume and the source selection. Source of joy Up to ten (10 !) stereo sources can be connected to the Director Mk2. Six of them are for analog and four for digital input signals. The source selection is shown in the dot matrix LED display: IN 1 through IN 6 for the analog inputs. AES, USB, COAX, OPTI for the digital inputs, where the detected sample rate is displayed after about two seconds. For example U768 = USB input with 768kHz sampling rate. The source selection can also be operated remotely if the rotary switch is set to the “Remote” position. The Director Mk2 offers two pairs of balanced inputs with XLR connectors and four standard inputs with gold-plated RCA connectors. On the digital side there are four additional inputs. PCM audio is received in S/P-DIF format via coaxial Cinch, optical Toslink and balanced XLR (AES). Both PCM audio and DSD audio can be converted via USB. The DAC768 The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the digital-to-analog converter, which thanks to its new architecture reproduces the finest sound details. It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768kHz, which is equivalent to 16 times CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. The DLP120 The analog output of the DAC chip must be filtered by a low pass filter. Director Mk2 has two of them: One for PCM audio and one for DSD audio, since different roll-off frequencies are required. And in contrast to all other DACs in the world, the low pass filters here are built using VOLTAiR technology, which provides a plus in dynamics and headroom. Good ol' times Two mechanical VU meters visualize the input levels for the left and right audio channel. With the VU switch you can optimize the display for different signal levels. Tape Monitor A tape monitor circuitry is quite retro. Who still owns a cassette recorder or a tape machine? Who still has an equalizer? To put it another way: Who would like to do it and cannot do it because no manufacturer offers a tape monitor circuit anymore? Well, those who want can again. Today’s audio levels are much higher than in the past and many recorders will be overloaded by them. In that case simply press the switch and the level to the recorder is lowered by 10 dB. To compensate, the level from the recorder is increased by 10 dB. Et voilà. Preamp & Direct Out On the output side, power amplifiers or active loudspeakers can be connected to the preamp output sockets using XLRs. The Direct Out via RCA picks up the output signal before the volume control and thus offers the possibility to connect a headphone amplifier. AMP CTL Practical are the AMP CTL sockets to which power amplifiers with 12 V trigger inputs can be connected in order to remotely switch them on and off together with the Director Mk2. Specifications: Analog Inputs & Outputs: XLR (balanced), RCA Maximum input & output gain: 32.5 dBu Input impedance (RCA): 47 kΩ Input impedance (XLR): 20 kΩ Output impedance: 75 Ω Common mode rejection (XLR): -82 dBu Frequency range (-3 dB): 4 Hz – 300 Crosstalk (1 kHz): -108 dBu THD (0 dBu, 1 kHz): 0.000992 % Noise (A-weighted): -102.5 dBu Dynamic range: 135 dB Digital Inputs, DAC768 AES/EBU (XLR), PCM sample rates: 44.1/48/88.2/96/176.4/192 kHz Coaxial SPDIF (RCA), PCM sample rates: 44.1/48/88.2/96/176.4/192 kHz Optical SPDIF (Toslink F06), PCM sample rates: 44.1/48/88.2/96/with Glass fibre

The director sets the tone. The central unit of the HiFi system is the preamplifier. With remote source selection and volume control, retro-look-VU-meter, premium DA-converter and the all superior VOLTAiR technology, the Director Mk2 caters for musical blockbusters. Milled from solid is the big 45mm Volume control. Its mass together with the  motorized Alps RK27 “Big Blue” potentiometer enhances the “spoon in the honey” feeling even further. The red marker LED makes the setting visible even in darkened environments. Volume RC The volume can be remote controlled with any infrared remote control, that the Director Mk2 simply learns. Learning made easy This video explains how you can use any infrared remote control to remotely control the volume and the source selection. Source of joy Up to ten (10 !) stereo sources can be connected to the Director Mk2. Six of them are for analog and four for digital input signals. The source selection is shown in the dot matrix LED display: IN 1 through IN 6 for the analog inputs. AES, USB, COAX, OPTI for the digital inputs, where the detected sample rate is displayed after about two seconds. For example U768 = USB input with 768kHz sampling rate. The source selection can also be operated remotely if the rotary switch is set to the “Remote” position. The Director Mk2 offers two pairs of balanced inputs with XLR connectors and four standard inputs with gold-plated RCA connectors. On the digital side there are four additional inputs. PCM audio is received in S/P-DIF format via coaxial Cinch, optical Toslink and balanced XLR (AES). Both PCM audio and DSD audio can be converted via USB. The DAC768 The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the digital-to-analog converter, which thanks to its new architecture reproduces the finest sound details. It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768kHz, which is equivalent to 16 times CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. The DLP120 The analog output of the DAC chip must be filtered by a low pass filter. Director Mk2 has two of them: One for PCM audio and one for DSD audio, since different roll-off frequencies are required. And in contrast to all other DACs in the world, the low pass filters here are built using VOLTAiR technology, which provides a plus in dynamics and headroom. Good ol' times Two mechanical VU meters visualize the input levels for the left and right audio channel. With the VU switch you can optimize the display for different signal levels. Tape Monitor A tape monitor circuitry is quite retro. Who still owns a cassette recorder or a tape machine? Who still has an equalizer? To put it another way: Who would like to do it and cannot do it because no manufacturer offers a tape monitor circuit anymore? Well, those who want can again. Today’s audio levels are much higher than in the past and many recorders will be overloaded by them. In that case simply press the switch and the level to the recorder is lowered by 10 dB. To compensate, the level from the recorder is increased by 10 dB. Et voilà. Preamp & Direct Out On the output side, power amplifiers or active loudspeakers can be connected to the preamp output sockets using XLRs. The Direct Out via RCA picks up the output signal before the volume control and thus offers the possibility to connect a headphone amplifier. AMP CTL Practical are the AMP CTL sockets to which power amplifiers with 12 V trigger inputs can be connected in order to remotely switch them on and off together with the Director Mk2. Specifications: Analog Inputs & Outputs: XLR (balanced), RCA Maximum input & output gain: 32.5 dBu Input impedance (RCA): 47 kΩ Input impedance (XLR): 20 kΩ Output impedance: 75 Ω Common mode rejection (XLR): -82 dBu Frequency range (-3 dB): 4 Hz – 300 Crosstalk (1 kHz): -108 dBu THD (0 dBu, 1 kHz): 0.000992 % Noise (A-weighted): -102.5 dBu Dynamic range: 135 dB Digital Inputs, DAC768 AES/EBU (XLR), PCM sample rates: 44.1/48/88.2/96/176.4/192 kHz Coaxial SPDIF (RCA), PCM sample rates: 44.1/48/88.2/96/176.4/192 kHz Optical SPDIF (Toslink F06), PCM sample rates: 44.1/48/88.2/96/with Glass fibre

The director sets the tone. The central unit of the HiFi system is the preamplifier. With remote source selection and volume control, retro-look-VU-meter, premium DA-converter and the all superior VOLTAiR technology, the Director Mk2 caters for musical blockbusters. Milled from solid is the big 45mm Volume control. Its mass together with the  motorized Alps RK27 “Big Blue” potentiometer enhances the “spoon in the honey” feeling even further. The red marker LED makes the setting visible even in darkened environments. Volume RC The volume can be remote controlled with any infrared remote control, that the Director Mk2 simply learns. Learning made easy This video explains how you can use any infrared remote control to remotely control the volume and the source selection. Source of joy Up to ten (10 !) stereo sources can be connected to the Director Mk2. Six of them are for analog and four for digital input signals. The source selection is shown in the dot matrix LED display: IN 1 through IN 6 for the analog inputs. AES, USB, COAX, OPTI for the digital inputs, where the detected sample rate is displayed after about two seconds. For example U768 = USB input with 768kHz sampling rate. The source selection can also be operated remotely if the rotary switch is set to the “Remote” position. The Director Mk2 offers two pairs of balanced inputs with XLR connectors and four standard inputs with gold-plated RCA connectors. On the digital side there are four additional inputs. PCM audio is received in S/P-DIF format via coaxial Cinch, optical Toslink and balanced XLR (AES). Both PCM audio and DSD audio can be converted via USB. The DAC768 The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the digital-to-analog converter, which thanks to its new architecture reproduces the finest sound details. It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768kHz, which is equivalent to 16 times CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. The DLP120 The analog output of the DAC chip must be filtered by a low pass filter. Director Mk2 has two of them: One for PCM audio and one for DSD audio, since different roll-off frequencies are required. And in contrast to all other DACs in the world, the low pass filters here are built using VOLTAiR technology, which provides a plus in dynamics and headroom. Good ol' times Two mechanical VU meters visualize the input levels for the left and right audio channel. With the VU switch you can optimize the display for different signal levels. Tape Monitor A tape monitor circuitry is quite retro. Who still owns a cassette recorder or a tape machine? Who still has an equalizer? To put it another way: Who would like to do it and cannot do it because no manufacturer offers a tape monitor circuit anymore? Well, those who want can again. Today’s audio levels are much higher than in the past and many recorders will be overloaded by them. In that case simply press the switch and the level to the recorder is lowered by 10 dB. To compensate, the level from the recorder is increased by 10 dB. Et voilà. Preamp & Direct Out On the output side, power amplifiers or active loudspeakers can be connected to the preamp output sockets using XLRs. The Direct Out via RCA picks up the output signal before the volume control and thus offers the possibility to connect a headphone amplifier. AMP CTL Practical are the AMP CTL sockets to which power amplifiers with 12 V trigger inputs can be connected in order to remotely switch them on and off together with the Director Mk2. Specifications: Analog Inputs & Outputs: XLR (balanced), RCA Maximum input & output gain: 32.5 dBu Input impedance (RCA): 47 kΩ Input impedance (XLR): 20 kΩ Output impedance: 75 Ω Common mode rejection (XLR): -82 dBu Frequency range (-3 dB): 4 Hz – 300 Crosstalk (1 kHz): -108 dBu THD (0 dBu, 1 kHz): 0.000992 % Noise (A-weighted): -102.5 dBu Dynamic range: 135 dB Digital Inputs, DAC768 AES/EBU (XLR), PCM sample rates: 44.1/48/88.2/96/176.4/192 kHz Coaxial SPDIF (RCA), PCM sample rates: 44.1/48/88.2/96/176.4/192 kHz Optical SPDIF (Toslink F06), PCM sample rates: 44.1/48/88.2/96/with Glass fibre

Το Phonitor x, είναι ο απόλυτος ενισχυτής ακουστικών. Προσφέρει συνδέσεις για ακουστικά τόσο balanced όσο και unbalanced, ενώ με ισχύ εξόδου 3.7 W, η απόδοσή του είναι εντυπωσιακή.  Το επαναστατικό σύστημα Phonitor Matrix, προσφέρει την πιό ρεαλιστική ακρόαση για ακουστικά, αφού δημιουργεί την εντύπωση ακρόασης μέσω ηχείων. Το Phonitor x, δεν είναι μόνο ενισχυτής ακουστικών, αλλά και ένας εξαιρετικός προενισχυτής, όπου μπορείτε να συνδέσετε έναν τελικό ενισχυτή ή ενεργά ηχεία μόνιτορ Προδιαγραφές: Ενισχυτής ακουστικών και προενισχυτής, τεχνολογίας VOLTAiR 120 V Rail,  Ξεχωριστές συνδέσεις για ακουστικά και τελικό ενισχυτή balanced και unbalanced,  Κατάλληλο για όλα τα ακουστικά με αντίσταση μεγαλύτερη από 10 ohms,  Είσοδοι balanced και unbalanced (XLR και RCA),  Προαιρετικά ψηφιακές εισόδους: USB, coaxial and optical,  Προαιρετικά μετατροπέας DAC: 192 kHz / 24 Bit,  Έξοδοι balanced και unbalanced (XLR και RCA),  Phonitor Matrix για προσομοίωση ακρόασης ηχείων,  Έλεγχος Laterality: super-fine balance,  Διακόπτης Mono,  Έλεγχος στάθμης (ελέγχεται και με τηλεχειριστήριο),  Μέγιστη ισχύς εξόδου: 2 x 3.7 W (120 ohms),  Απόκριση συχνότητας: 10 Hz - 300 kHz (-3 dB),  THD+N: 0.00091 % (HP), 0.00085 % (Line),  Dynamic range: 135.5 dB (HP), 136.3 dB (Line),  Σύνδεση AMP CTR με τον τελικό ενισχυτή Performer (για έλεγχο του διακόπτη on/off),  Made in Germany Χαρακτηριστικά: Απόκριση Συχνότητας: ‹10Hz - ›200kHz (-3dB) Αριθμός Εισόδων: 2 Αριθμός Εξόδων: 2 & 1(Headphones) Δυναμική Περιοχή: 129,5 dBΑ Ενισχυτής Ακουστικών: ΝΑΙ Συνδετήρες Εισόδου: 2 x XLR Συνδετήρες Εξόδου: 2 x XLR 1 x TRS Τύπος Ενίσχυσης: Ενεργή