Headphones Amps
The headphone amplifier, monitoring controller and DAC with 120V technology Phonitor 3 DAC is not only the ultimate headphone amplifier and monitoring controller with 120V technology – the integrated DAC makes it the perfect monitoring centerpiece for demanding producers as well as sound and mastering engineers working with digital sources or in the DAW.Whether if USB, AES/EBU or S/PDIF – the integrated DAC with analog SLP120 converts digital PCM audio signals with a resolution of 32 bit and a sampling rate of up to 768 kHz. It converts DSD signals with a resolution of up to DSD256.On the analog side, the Phonitor 3 DAC, based on the SPL 120V technology, offers the same monitoring quality as the big SPL mastering consoles – on loudspeakers and headphones.The analog Phonitor Matrix allows mixing and mastering on headphones in the highest quality – with the same spatial perception of the stereo stage as on loudspeakers.Great sound – for headphonesThe Phonitor 3 offers connection for a standard headphone with a stereo jack plug on the front. Thanks to the enormous output power, all kind of headphones are driven effortlessly. Thus, it plays out the advantages of the SPL 120V technology and rewards the listener with an honest, detailed and at the same time vivid sound experience.Great sound – also for loudspeakersOn the rear of the device, Phonitor 3 offersa stereo output which makes it a high-qualitymonitoring controller for any monitoring situation. Active speakers with an integrated power amplifieror passive speakers in combination with a power amplifier can be connected at this output.Monitoring at the highest levelPhonitor 3 offers the same key technology –SPL 120V technology – and signal quality as thebig SPL DMC and MMC mastering consoles.
It’s head-fi. It’s desk-fi. And it’s hi-fi.The NEO iDSD 2 is our versatile new 3-in-1 DAC/Amp, designed specifically for CAS audiophiles. It pairs effortlessly with your headphones as a Head-Fi DAC/Amp, can be used as a pure DAC with your integrated amplifier, or serve as a DAC/Preamp for your active speakers and power amplifier.It features the latest Bluetooth 5.4, supporting the new aptX Lossless, the only Bluetooth codec capable of streaming lossless CD-quality audio without sacrificing audio quality.The NEO iDSD 2 has improved headphone and line outputs, providing ample power for your high-demanding headphones, as well as power amplifiers.My Blue isn’t your blue. It’s new and Lossless.The NEO iDSD 2 features the latest Bluetooth 5.4 technology, supporting the new aptX Lossless codec, which provides a maximum bitrate of 1,200kbps. In comparison, aptX Adaptive has a maximum bitrate of 420kbps, while LDACTM offers a higher bitrate of 990kbps.However, aptX Lossless is the first and only Bluetooth codec capable of streaming CD-quality audio without using a compression method that degrades sound quality. While other Bluetooth codecs claim to support CD-quality and even hi-res audio, they employ lossy compression during transmission, which negatively affects sound quality.The NEO iDSD 2 used Qualcomm’s new QCC518x Bluetooth audio chip, is qualified to Bluetooth 5.4, supported all* Bluetooth formats including: aptX Lossless, aptX Adaptive, aptX, LDACTM, LHDC/HWA, AAC and SBC.*As of 22 Sep 2023. Check your device for Bluetooth codec support.**LDAC and LDAC logo are trademarks of Sony Corporation.5x more headphone output power than its predecessor.You heard me correctly – the headphone output power of the NEO iDSD 2 is a whopping 5 times more powerful than that of the 1st-gen NEO iDSD. With a maximum headphone output power of 5,551 mW (@ 32Ω), it outperforms even some dedicated headphone amplifiers, making them sweat. The headphone section has seen significant improvement, as we’ve essentially integrated a Diablo headphone circuit into it.It features Auto iEMatch to reduce annoying hiss from high-sensitivity headphones without losing any dynamic range and four gain settings ranging from -12dB to +16dB, making it suitable for all your IEMs and headphone types, from super-sensitive to power-hungry.The NEO iDSD 2 is not only a powerhouse, but it’s also tailored for your ears. The newly added analogue processing modes, XSpace and XBass II, along with the four digital filters, allow you to finetune the sound. Both XSpace and XBass II are pure analogue signal processing modes designed to adjust the soundstage and low-frequency response to match your headphones.Stand by you. No matter up or down.Whether you’re using the NEO iDSD 2 as a Desk-Fi or Hi-Fi, you can position it horizontally or vertically. The new 2-inch colour display automatically rotates to suit the orientation.When using it as a Desk-Fi, you can position it vertically on your desk to save space. Set it to variable output, and with its powerful 19.5V maximum balanced output, it works well with your active speakers with volume control. The volume control is analogue, which is superior to any digital volume control.When using the NEO iDSD 2 as a Hi-Fi, you can place it horizontally. It can serve as a pure DAC, playing all Hi-Res music files from PCM 32-bit/768kHz to DSD512 and full MQA decoding. You can also connect it directly to your power amplifier as a preamplifier, utilising its analogue volume control.GMT Femto-Precision Clock. Upgradable.The internal GMT femto-precision clock, combined with a smart storage cache, forms an advanced jitter reduction system. It effectively reduces jitter in the digital signal, producing cleaner and more accurate sound.If you possess a more accurate external clock, or if you wish to synchronize with other devices such as CD players or network streamers that have an external clock input, you can connect both the NEO iDSD 2 and the other devices to the external clock via the 10MHz External Sync Clock input for even greater clock signal accuracy.It’s rare to find an External Sync Clock input in this price range. Even if you don’t have an external clock, the internal GMT femto-precision clock still offers excellent performance in its class.More than new features. Enhanced circuitry.The NEO iDSD 2’s enhanced PureWave circuit design, with its balanced dual-mono topology and short signal paths, is known for outstanding linearity and minimal noise and distortion, offering you exceptional sonic purity.The results are an improved Signal-to-Noise Ratio (SNR) of >120dB(A), Dynamic Range (DNR) of -120dB(A), and Total Harmonic Distortion plus Noise (THD+N) of
Premium DAC with VOLTAiR technologyDiamond is the perfect DAC and preamplifier for everyone who plays music exclusively from digital sources. Diamond offers connectivity for six digital sources and an external word clock. The superior VOLTAiR technology and the premium DAC with the unequalled DLP120 combined with an analog volume control allowing for highest resolution at any volume makes the Diamond an one-of-a-kind DA converter that delivers finest soundstages with an unrivalled analog feel.Everything under controlThe volume is adjusted with a solid, milled aluminum, rotary knob. The Alps RK27 “Big Blue” potentiometer gives a pleasant “spoon in the honey” rotary feel.Source of joyUp to 6 digital stereo sources can be connected to Diamond.Diamond offers each a stereo USB and AES input as well as each two optical and coaxial stereo inputs. Via USB, both PCM audio and DSD audio can be converted. PCM audio is received in S/PDIF format, both coaxial (RCA), optical (Toslink F06) and balanced (AES/EBU). The source selection is done via the selection control on the front. The selected input is also shown in the dot matrix LED display: USB, COA1, COA2, OPT1, OPT2 or AES. After approximately two seconds, the display shows the type of clock source and the detected sampling rate.Always in timeDiamond can not only synchronize to the clock integrated in the digitally fed source signal. As a specialist for digital players Diamond offers a word clock input. The source of the clock signal can be selected via the CLOCK switch.Source = Diamond synchronizes to the digital clock in the source signal.Word = Diamond synchronizes to the digital clock present at WORD IN.Well informedThe DAC automatically picks up the sampling rate and resolution of the digital playback source. No matter if a streamer, computer, CD player or an external word clock is connected. The detected sampling rate and the selected clock source are shown in the dot matrix LED display. For example, U768 is an acronym for a clock signal in the USB stream with a sampling rate of 768 kHz.All variable – or Slave ThruDiamond provides two stereo output pairs for connecting power amplifiers or active loudspeakers. One pair of outputs with XLR, the other with RCA outputs. Both have the same output signal, which is controlled by the volume control on the front panel. The volume control for both outputs can be individually switched out of the signal path via DIP switch on the back of the device. For example, a headphone amplifier with its own volume control can be connected to one of the outputs.The DAC768The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the digital-to-analogue converter, which thanks to its architecture reproduces the finest sound details.It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768 kHz, which is equivalent to 16 times CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. In contrast to the DAC 768xs, the DAC768 not only offers an AES/EBU digital input, but also the SPL DLP120 with VOLTAiR technology.The DLP120 (Dual Low-Pass)The analog output of the DAC chip must be filtered by a low pass filter. Phonitor xe has two of them: One for PCM audio and one for DSD audio, since different roll-off frequencies are required.In contrast to all other DACs in the world, the low pass filters here are built using VOLTAiR technology, which provides a plus in dynamics and headroom and sound.Sounds goodWith all devices of the Professional Fidelity series we develop not only according to plan, but also by ear. Many important components are installed on the circuit boards using Through-hole technology. This way we can ensure that we can use the best sounding components.The VOLTAiR TechnologyThe 120V technology is our reference technology. The 120V technology is unique in the world. It operates at a DC voltage of 120 volts. This is four times that of IC-based semiconductor op-amps. In our Professional Fidelity series, we refer to this unsurpassed technology as VOLTAiR technology.The highest possible audio quality requires the highest possible audio operating voltageThe 120V technology works with +/-60 V. To be able to handle such a high voltage, we have developed special proprietary operational amplifiers that can operate with a DC voltage of +/-60 V: the SPL 120V SUPRA operational amplifiers. This high voltage would destroy conventional components and operational amplifiers.The 120V technology achieves exceptional technical specifications and sonic benefits. Technically, in terms of dynamic range, signal-to-noise ratio and headroom. Sonically, in terms of richness of detail and an absolutely relaxed listening experience. By the way, the “120V” in the name of the technology has nothing to do with the local mains voltage from the mains power socket. This is about the operating voltage inside the device with which the audio signals are processed.The mains voltage from the mains power socket is transformed to the required secondary voltage in the device’s internal linear power supply with toroidal transformer. Rectifiers convert this AC voltage into DC voltage required in the audio device.VOLTAiR is a composition of the terms Volt and Air. Volt is the unit for electrical voltage and Air stands for the unlimited space the music can breathe in. It symbolizes the perceived limitless dynamics resulting from high audio voltage.ComparisonMost audio devices work with an internal operating voltage of +/-15 volts and can thus process a maximum input level of +21.5 dBu. If a DAC, for example, has an output level of +22 dBu at 0 dBFS, level peaks of the music material would already cause overloads in the input stage of the device. All components in the audio device often operate at their limits. The result is an unsteady sound that causes stress and faster ear fatigue.SPL devices with VOLTAiR technology can handle input levels of +32.5 dBu thanks to the higher internal operating voltage of +/- 60 volts – thus offering 12 dB more headroom. All components consequently operate continuously in the optimum operating range. The result is a very pleasant, natural and relaxed sound experience. So you can enjoy your music in every detail.
Premium DAC with VOLTAiR technologyDiamond is the perfect DAC and preamplifier for everyone who plays music exclusively from digital sources. Diamond offers connectivity for six digital sources and an external word clock. The superior VOLTAiR technology and the premium DAC with the unequalled DLP120 combined with an analog volume control allowing for highest resolution at any volume makes the Diamond an one-of-a-kind DA converter that delivers finest soundstages with an unrivalled analog feel.Everything under controlThe volume is adjusted with a solid, milled aluminum, rotary knob. The Alps RK27 “Big Blue” potentiometer gives a pleasant “spoon in the honey” rotary feel.Source of joyUp to 6 digital stereo sources can be connected to Diamond.Diamond offers each a stereo USB and AES input as well as each two optical and coaxial stereo inputs. Via USB, both PCM audio and DSD audio can be converted. PCM audio is received in S/PDIF format, both coaxial (RCA), optical (Toslink F06) and balanced (AES/EBU). The source selection is done via the selection control on the front. The selected input is also shown in the dot matrix LED display: USB, COA1, COA2, OPT1, OPT2 or AES. After approximately two seconds, the display shows the type of clock source and the detected sampling rate.Always in timeDiamond can not only synchronize to the clock integrated in the digitally fed source signal. As a specialist for digital players Diamond offers a word clock input. The source of the clock signal can be selected via the CLOCK switch.Source = Diamond synchronizes to the digital clock in the source signal.Word = Diamond synchronizes to the digital clock present at WORD IN.Well informedThe DAC automatically picks up the sampling rate and resolution of the digital playback source. No matter if a streamer, computer, CD player or an external word clock is connected. The detected sampling rate and the selected clock source are shown in the dot matrix LED display. For example, U768 is an acronym for a clock signal in the USB stream with a sampling rate of 768 kHz.All variable – or Slave ThruDiamond provides two stereo output pairs for connecting power amplifiers or active loudspeakers. One pair of outputs with XLR, the other with RCA outputs. Both have the same output signal, which is controlled by the volume control on the front panel. The volume control for both outputs can be individually switched out of the signal path via DIP switch on the back of the device. For example, a headphone amplifier with its own volume control can be connected to one of the outputs.The DAC768The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the digital-to-analogue converter, which thanks to its architecture reproduces the finest sound details.It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768 kHz, which is equivalent to 16 times CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. In contrast to the DAC 768xs, the DAC768 not only offers an AES/EBU digital input, but also the SPL DLP120 with VOLTAiR technology.The DLP120 (Dual Low-Pass)The analog output of the DAC chip must be filtered by a low pass filter. Phonitor xe has two of them: One for PCM audio and one for DSD audio, since different roll-off frequencies are required.In contrast to all other DACs in the world, the low pass filters here are built using VOLTAiR technology, which provides a plus in dynamics and headroom and sound.Sounds goodWith all devices of the Professional Fidelity series we develop not only according to plan, but also by ear. Many important components are installed on the circuit boards using Through-hole technology. This way we can ensure that we can use the best sounding components.The VOLTAiR TechnologyThe 120V technology is our reference technology. The 120V technology is unique in the world. It operates at a DC voltage of 120 volts. This is four times that of IC-based semiconductor op-amps. In our Professional Fidelity series, we refer to this unsurpassed technology as VOLTAiR technology.The highest possible audio quality requires the highest possible audio operating voltageThe 120V technology works with +/-60 V. To be able to handle such a high voltage, we have developed special proprietary operational amplifiers that can operate with a DC voltage of +/-60 V: the SPL 120V SUPRA operational amplifiers. This high voltage would destroy conventional components and operational amplifiers.The 120V technology achieves exceptional technical specifications and sonic benefits. Technically, in terms of dynamic range, signal-to-noise ratio and headroom. Sonically, in terms of richness of detail and an absolutely relaxed listening experience. By the way, the “120V” in the name of the technology has nothing to do with the local mains voltage from the mains power socket. This is about the operating voltage inside the device with which the audio signals are processed.The mains voltage from the mains power socket is transformed to the required secondary voltage in the device’s internal linear power supply with toroidal transformer. Rectifiers convert this AC voltage into DC voltage required in the audio device.VOLTAiR is a composition of the terms Volt and Air. Volt is the unit for electrical voltage and Air stands for the unlimited space the music can breathe in. It symbolizes the perceived limitless dynamics resulting from high audio voltage.ComparisonMost audio devices work with an internal operating voltage of +/-15 volts and can thus process a maximum input level of +21.5 dBu. If a DAC, for example, has an output level of +22 dBu at 0 dBFS, level peaks of the music material would already cause overloads in the input stage of the device. All components in the audio device often operate at their limits. The result is an unsteady sound that causes stress and faster ear fatigue.SPL devices with VOLTAiR technology can handle input levels of +32.5 dBu thanks to the higher internal operating voltage of +/- 60 volts – thus offering 12 dB more headroom. All components consequently operate continuously in the optimum operating range. The result is a very pleasant, natural and relaxed sound experience. So you can enjoy your music in every detail.
Premium DAC with VOLTAiR technologyDiamond is the perfect DAC and preamplifier for everyone who plays music exclusively from digital sources. Diamond offers connectivity for six digital sources and an external word clock. The superior VOLTAiR technology and the premium DAC with the unequalled DLP120 combined with an analog volume control allowing for highest resolution at any volume makes the Diamond an one-of-a-kind DA converter that delivers finest soundstages with an unrivalled analog feel.Everything under controlThe volume is adjusted with a solid, milled aluminum, rotary knob. The Alps RK27 “Big Blue” potentiometer gives a pleasant “spoon in the honey” rotary feel.Source of joyUp to 6 digital stereo sources can be connected to Diamond.Diamond offers each a stereo USB and AES input as well as each two optical and coaxial stereo inputs. Via USB, both PCM audio and DSD audio can be converted. PCM audio is received in S/PDIF format, both coaxial (RCA), optical (Toslink F06) and balanced (AES/EBU). The source selection is done via the selection control on the front. The selected input is also shown in the dot matrix LED display: USB, COA1, COA2, OPT1, OPT2 or AES. After approximately two seconds, the display shows the type of clock source and the detected sampling rate.Always in timeDiamond can not only synchronize to the clock integrated in the digitally fed source signal. As a specialist for digital players Diamond offers a word clock input. The source of the clock signal can be selected via the CLOCK switch.Source = Diamond synchronizes to the digital clock in the source signal.Word = Diamond synchronizes to the digital clock present at WORD IN.Well informedThe DAC automatically picks up the sampling rate and resolution of the digital playback source. No matter if a streamer, computer, CD player or an external word clock is connected. The detected sampling rate and the selected clock source are shown in the dot matrix LED display. For example, U768 is an acronym for a clock signal in the USB stream with a sampling rate of 768 kHz.All variable – or Slave ThruDiamond provides two stereo output pairs for connecting power amplifiers or active loudspeakers. One pair of outputs with XLR, the other with RCA outputs. Both have the same output signal, which is controlled by the volume control on the front panel. The volume control for both outputs can be individually switched out of the signal path via DIP switch on the back of the device. For example, a headphone amplifier with its own volume control can be connected to one of the outputs.The DAC768The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the digital-to-analogue converter, which thanks to its architecture reproduces the finest sound details.It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768 kHz, which is equivalent to 16 times CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. In contrast to the DAC 768xs, the DAC768 not only offers an AES/EBU digital input, but also the SPL DLP120 with VOLTAiR technology.The DLP120 (Dual Low-Pass)The analog output of the DAC chip must be filtered by a low pass filter. Phonitor xe has two of them: One for PCM audio and one for DSD audio, since different roll-off frequencies are required.In contrast to all other DACs in the world, the low pass filters here are built using VOLTAiR technology, which provides a plus in dynamics and headroom and sound.Sounds goodWith all devices of the Professional Fidelity series we develop not only according to plan, but also by ear. Many important components are installed on the circuit boards using Through-hole technology. This way we can ensure that we can use the best sounding components.The VOLTAiR TechnologyThe 120V technology is our reference technology. The 120V technology is unique in the world. It operates at a DC voltage of 120 volts. This is four times that of IC-based semiconductor op-amps. In our Professional Fidelity series, we refer to this unsurpassed technology as VOLTAiR technology.The highest possible audio quality requires the highest possible audio operating voltageThe 120V technology works with +/-60 V. To be able to handle such a high voltage, we have developed special proprietary operational amplifiers that can operate with a DC voltage of +/-60 V: the SPL 120V SUPRA operational amplifiers. This high voltage would destroy conventional components and operational amplifiers.The 120V technology achieves exceptional technical specifications and sonic benefits. Technically, in terms of dynamic range, signal-to-noise ratio and headroom. Sonically, in terms of richness of detail and an absolutely relaxed listening experience. By the way, the “120V” in the name of the technology has nothing to do with the local mains voltage from the mains power socket. This is about the operating voltage inside the device with which the audio signals are processed.The mains voltage from the mains power socket is transformed to the required secondary voltage in the device’s internal linear power supply with toroidal transformer. Rectifiers convert this AC voltage into DC voltage required in the audio device.VOLTAiR is a composition of the terms Volt and Air. Volt is the unit for electrical voltage and Air stands for the unlimited space the music can breathe in. It symbolizes the perceived limitless dynamics resulting from high audio voltage.ComparisonMost audio devices work with an internal operating voltage of +/-15 volts and can thus process a maximum input level of +21.5 dBu. If a DAC, for example, has an output level of +22 dBu at 0 dBFS, level peaks of the music material would already cause overloads in the input stage of the device. All components in the audio device often operate at their limits. The result is an unsteady sound that causes stress and faster ear fatigue.SPL devices with VOLTAiR technology can handle input levels of +32.5 dBu thanks to the higher internal operating voltage of +/- 60 volts – thus offering 12 dB more headroom. All components consequently operate continuously in the optimum operating range. The result is a very pleasant, natural and relaxed sound experience. So you can enjoy your music in every detail.
The headphone amplifier, monitoring controller and DAC with 120V technology Phonitor 3 DAC is not only the ultimate headphone amplifier and monitoring controller with 120V technology – the integrated DAC makes it the perfect monitoring centerpiece for demanding producers as well as sound and mastering engineers working with digital sources or in the DAW. Whether if USB, AES/EBU or S/PDIF – the integrated DAC with analog SLP120 converts digital PCM audio signals with a resolution of 32 bit and a sampling rate of up to 768 kHz. It converts DSD signals with a resolution of up to DSD256. On the analog side, the Phonitor 3 DAC, based on the SPL 120V technology, offers the same monitoring quality as the big SPL mastering consoles – on loudspeakers and headphones. The analog Phonitor Matrix allows mixing and mastering on headphones in the highest quality – with the same spatial perception of the stereo stage as on loudspeakers.Great sound – for headphonesThe Phonitor 3 DAC offers connection for a standard headphone with a stereo jack plug on the front. Thanks to the enormous output power, all kind of headphones are driven effortlessly. Thus, it plays out the advantages of the SPL 120V technology and rewards the listener with an honest, detailed and at the same time vivid sound experience.Great sound – also for loudspeakersOn the rear of the device, Phonitor 3 DAC offers a stereo output which makes it a high-quality monitoring controller for any monitoring situation. Active speakers with an integrated power amplifier or passive speakers in combination with a power amplifier can be connected at this output.Monitoring at the highest levelPhonitor 3 DAC offers the same key technology – SPL 120V technology – and signal quality as the big SPL DMC and MMC mastering consoles.Headphones or SpeakersThe Output switch – simply switch from headphone to speaker playback. In the center position (Mute), no signal reaches the outputs. The VU meters light up red.Digital & analog stereo inputs – free choiceUp to six stereo sources can be connected to the Phonitor 3 DAC. The source is selected via the Source switch.Analog inputsOn the analog side, two analog stereo inputs are offered, each with two XLR line inputs. Professional analog players with balanced outputs and line level can be connected here.Digital inputsOn the digital side, the Phonitor 3 DAC offers four digital stereo inputs.USBThe USB input (type B) can be used to directly connect the DAW. No driver installation is required for operation with a Mac or an iDevice. Via USB, the Phonitor 3 DAC converts PCM audio signals with a resolution of 32 bits and a sampling rate of up to 768 kHz as well as DSD signals with a resolution of up to DSD256.S/PDIF, coaxialThe Input S/PDIF coaxial can also receive a two-channel signal (PCM audio) with sampling rates up to 192 kHz and a bit rate of 16 bits to 24 bits. Unbalanced, 2-wire 75-ohm coaxial cables with RCA connectors are used for signal transmission.S/PDIF, opticalThe S/PDIF optical input can also receive a two-channel signal (PCM audio) with sampling rates of up to 192 kHz and a bit rate of 16 bit to 24 bit. The input jack is an F05 jack. This interface is better known under the Toshiba brand name TOSLINK.Tip: You should attach importance to the quality of the optical fiber. With inexpensive plastic optical fibers, transmissions with quad sampling rates (176.4kHz/192kHz) may have faults. In this case a glass fiber optic cable should be chosen.AES/EBUThe AES input provides an input jack which corresponds to a standard XLR input (XLR, female). An AES signal can transport two encoded PCM audio channels with a maximum sampling rate of 192 kHz and a bit rate of 16 bits to 24 bits. This standard is defined under IEC 60958 Type I. Balanced, 3-core, 110 Ohm “twisted pair” cables with XLR plugs are used for connection.The DAC – the best is just good enoughThe converter chip in the Phonitor 3 DAC´s digital-to-analog converter is the highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip, which thanks to its architecture reproduces the finest sound details. It converts PCM audio at 32-bit resolution and a sampling rate of up to 768 kHz, which is 16 times the resolution of a CD. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256.SLP120The analog output of any DAC chip must be filtered by a low pass filter when entering the analog world. In contrast to all other DACs in the world, the low pass filters here are built using SPL 120V technology, which provides a plus in dynamics and headroom and sound. The DAC in the Phonitor 3 DAC is equipped with the SLP120 – an analog “single low pass” filter with 120V technology.Milled from solidThe massive 45mm volume control knob milled from aluminum is a haptic highlight. Its mass together with the Alps RK27 “Big Blue” potentiometer enhances the “spoon in the honey” feeling even further and provides perfect control of the monitoring level.Monitoring without any compromisesThe Phonitor 3 DAC is a full-fledged monitor controller:Source selectionPhonitor Matrix with Crossfeed, Speaker Angle and Center Level (the latter can be switched off)Mono/StereoLaterality controlSolo L/RPhase inversion for L and RL/R SwapOutput switchable to headphones or speakersMuteMono or stereo – a matter of settingThe Mono/Stereo switch can be used to select whether the output signal of the Phonitor 3 DAC is a regular stereo signal or whether it is summed to a mono signal.Finding the real centerNaturally, hearing can be directed more to the left or more to the right. This becomes particularly clear when listening on headphones. Therefore, the Phonitor 3 DAC has the uniquely finely resolved laterality control, which rebalances the stereo image on the monitoring side. The Mono/Stereo switch can not only be used to switch between stereo or mono playback. This switch is also used to activate or deactivate the laterality control.Solo L/ROnly the right or left channel of the audio signal should be played back? The Solo L/R function makes it possible. If the triple selection switch is in the “L” position, only the left channel is played back – if it is in the “R” position, only the right channel is played back. In the middle position “Off” the Solo function is switched off. The regular stereo signal consisting of the left and right channel is thus present at the output of the Phonitor 3 DAC.L/R SwapA special feature is the channel swap function: L/R Swap. This function inverts the stereo image. Left becomes right and right becomes left. This is especially important and extremely time-saving, when you are monitoring samples in video dubbing that should match a scene with direction of movement. If the direction is not correct, you usually have to load the sample into the DAW to switch channels. before you can judge whether the sample matches the image. With the L/R Swap function, this is no longer necessary. You can now adjust the direction of movement on the Phonitor 3 DAC while pre-listening the sample library.Phase inversion for L and RWith this switch the phase of the left or right channel of the audio signal can be inverted. If the three-way selection switch is in the “L” position, the left channel is inverted – if it is in the “R” position, the right channel is inverted. In the middle position “Off” this function is switched off. At the output of the Phonitor 3 DAC the regular stereo signal is thus present.M/S – Mid or Side?By using the mono/stereo and L/R phase inversion switch in combination, it is also possible to only monitor the mid or side signal. When the switch is set to “Mono” and phase inversion is active for L (or R), only the side signal is played back. If the phase inversion is switched off, the mono signal corresponding to the “M” signal is played back. Separate monitoring of the M and S signals has become a widespread standard for many mixing and mastering engineers.Everything at a glanceTwo mechanical VU meters visualize the input levels for the left and right audio channels. The “VU Cal” switch can be used to reduce the signal visualized on the VU meters by -6 dB or -12 dB. Thus, the VU meters operate in the ideal display range even at very high input levels.The Revolution: Phonitor MatrixThe Phonitor Matrix is the revolution in the headphone amplifier.One of the unique features of SPL headphone amplifiers is the SPL Phonitor Matrix. It enables mixing and mastering engineers to create perfect mixes on headphones, which will translate perfectly to all types of stereo speaker systems. But the Phonitor Matrix is not only designed for professional use in the studio. It also enables the hifi enthusiast to enjoy music on headphones, like if it was played back on speakers.How is this possible?Music is normally produced and mixed for playback on stereo speakers. Listening on headphones is different from listening on loudspeakers. The biggest difference is the lack of crossing signals of the sound signal from the left speaker to the right ear and from the right speaker to the left ear.These crossing signals are missing in conventional headphone listening, because there are no signals crossing from one side of the headphones to the other. This results in an unnaturally wide stereo stage and sound sources are not played back at their actual position in the stereo spectrum. The SPL Phonitor Matrix can correct this false stereo image with an analog circuitry.Summed up:The SPL Phonitor Matrix corrects the false representation of the stereo sound image, which makes it much easier to find the right decisions for mixing and mastering engineers. The hifi enthusiast can experience the music, like it was originally mixed and recorded. So nothing stands in the way of a successful and long mixing session on headphones.Preamp Out or Direct OutWith a DIP switch on the rear of the device, the volume control for the rear stereo output can be switched out of the signal path. But that’s not all. It is also possible to output the Phonitor Matrix to the stereo output on the rear panel of the device – regardless of whether this is configured as Preamp Out (with volume control) or Direct Out (without volume control).More powerIf headphones have a rather low sensivity – no problem. With DIP switch 1 on the rear of the device, the level at the headphone output can be increased by 12 dB.Sounds goodWith all SPL devices we develop not only according to plan, but also by ear. All important components are installed on the circuit boards using Through-hole technology. This way we can ensure that we can use the best sounding components.The 120V technologyThe 120V technology is our reference technology. The 120V technology is unique in the world. It operates at a DC voltage of 120 volts. This is four times that of IC-based semiconductor op-amps.
DescriptionThe ZEN Air CAN is a powerful, hi-res home analogue amplifier that provides greater headphone enjoyment with any analogue source such as your PC, Mac, smartphone, tablet, streamer or TV.Amp it upThe ZEN Air CAN is an amplifier pure and simple.It simply takes an input signal from a source such as those mentioned above and creates a larger copy of the original signal before it’s sent to your headphones. Think about listening to sound with your hands over your ears and then removing them! Adding the ZEN Air CAN into your system is a little like that – back comes clarity of sound as well as volume.Lots to gain…The ZEN Air CAN comes with three gain settings so that it works well with every pair of headphones or in-ear monitors (also known as IEMs). What is gain? Gain in audio terms refers to an amplifier’s ability to increase the amplitude (size) of the signal from the source (input) to the headphones or speakers (output). More gain equals a stronger signal. You will need to adjust the gain depending on the sensitivity of the headphones or iEMs you are using. For example, highly sensitive headphones need lower gain. Play around with the settings. Trust your ears.eSpecially for youThe ZEN Air CAN has two different headphone sockets – 6.3mm single-ended and 4.4mm S-Balanced. There are basically two types of headphone – single-ended and balanced. In a nutshell, single-ended is the most common but the balanced option is often considered the better as it offers more power and control of the headphones. At iFi, we know not everyone has balanced headphones, so we’ve created our S-Balanced technology. This gives you all the benefits of a balanced connection – lower noise, less crosstalk – but without the need for balanced headphones.Sonic tailoringThe ZEN Air CAN boasts a couple of sonic tweaks, unique to iFi. XBass is analogue bass boost. In other words, it extends the bass response to suit different headphones. XSpace is an analogue headphone spatialiser. This opens up your music to give you the spaciousness of a live-concert atmosphere.TDK C0G (Class 1 ceramic) capacitors offer high stability and low losses for resonant circuit applications.Getting ever closer to the theoretical ideal of pure, frequency-constant capacitance, these capacitors reduce capacitor-induced distortion to vanishingly low levels.They are pricey but are a perfect addition to our products.Texas Instruments low-noise ICs offer great unity-gain bandwidth, very low noise and distortion, high output drive capability, Common-mode and Power Supply Rejection Ratios of over 100 dB, wide maximum-output-swing bandwidths and high slew rates.
The ZEN CAN Signature 6XX analogue headphone amplifier takes sonic tailoring to the next level with ActivEQ. ActivEQ This new feature, called ActivEQ, combines active and passive components to create a specific EQ curve to suit a particular pair of headphones, performed in the analogue domain without a hint of additional noise or distortion. The ZEN CAN Signature 6XX, features ActivEQ for the ‘MassDrop x Sennheiser HD 6XX’ – a popular pair of high-quality headphones with more than 120,000 sold to date, based on the Sennheiser HD 650 and created exclusively for Drop.com. These headphones are renowned for the quality of their midrange performance but exhibit some quirks in the bass and treble regions, which can be seen in frequency response measurements. EQ. Activated. When the ‘HD 6XX’ button is pressed, the ZEN CAN Signature 6XX calibrates its signal to complement the headphone’s response characteristics right across the frequency range, thus tailoring its performance to precisely fit the HD 6XX like a made-to-measure suit. In particular, the 7kHz treble and bass below 500Hz is gently elevated. What’s more, the benefits of this ActivEQ curve are equally applicable to the Sennheiser HD 650, which shares the same characteristics. It also has an effect on other Sennheiser models – take a look here. This feature can be switched on or off. Without ActivEQ engaged, the ZEN CAN Signature 6XX’s performance is adroitly balanced to make the most of all manner of headphones and in-ear monitors. No pain, just gain. The ZEN CAN Signature 6XX features four gain settings in six dB steps – 0dB, 6dB, 12dB and 18db. This enables the amp to precisely suit the connected headphones. Unity gain (0dB) is useful to ensure low noise with sensitive in-ear monitors, while the higher gain settings make the most of tougher headphone loads, delivering excellent dynamic headroom. XSpace This analogue processing mode compensates for the ‘in-head localisation’ effect that can occur when using headphones to listen to music that was mixed using a pair of speakers. It widens the headphone soundstage to deliver a more spacious and speaker-like experience. Balance of power The ZEN CAN Signature 6XX’s circuitry is a balanced, symmetrical dual-mono design – a topology usually reserved for high-end headphone amps – with a number of key elements trickled down from the discrete Class A circuitry developed for iFi’s flagship headphone amplifier, the Pro iCAN. Key components have been upgraded to enhance performance in line with the improvements made to the ZEN CAN Signature 6XX, including the use of Panasonic OS-CON and Elna Silmic II capacitors. Driving force The amp offers prodigious drive capability, delivering 1600mW (7.2V) into 32 ohms from the single-ended output, with 15V+ available to loads of 300 ohms or more through the balanced output, ensuring it takes even current-hungry planar headphones in its stride. Delivering ultra-low distortion, rich sonic detail, engaging dynamics and the ability to drive all manner of headphones with ease, the ZEN CAN Signature 6XX is a truly a driving force to be reckoned with. Stay connected The ZEN CAN Signature 6XX offers stereo RCA and 3.5mm single-ended inputs, plus a 4.4mm Balanced input. A 4.4mm balanced output is also provided, to connect to power amps equipped with a balanced input. It provides a pair of headphone outputs – a 6.3mm output for headphones that have a standard single-ended connector (compatible with all headphones) and a 4.4mm Balanced output for headphones offering balanced connection. An increasing number of high-quality headphones and in-ear monitors either come so equipped or give the option of detaching the cable and upgrading to a 4.4mm Balanced connector, and this output makes the most of them (it is particularly recommended for high-impedance headphones). Dynamic Duo The ZEN CAN Signature 6XX works well with the ZEN DAC Signature V2. Products can be bought separately but a ‘ZEN Signature Set’ is now available. This comprises both ZEN Signature units plus a high-performance 4.4mm Balanced cable (worth £69 when purchased separately) to connect them together. When used in tandem, the two ZEN Signatures make a fantastic, desktop-sized headphone system for both digital and analogue sources, further extending the reputation of iFi’s ZEN Series for delivering exceptional performance and versatility at remarkable prices.
Fantastic Beasts. Here’s where you find them. Portable DAC/amps tend to be compromised because they focus on a great digital OR a great analogue section. But not both. The xDSD Gryphon is different. Just like its mythical namesake, it is two beasts in one. From the Ultra-Res digital stage using the Burr-Brown MultiBit at the core to the PureWave analogue power section pumping out 1,000mW and other things in-between, it takes serious headphones to tame the Gryphon. Well-connected Separate Bluetooth + DAC + amp stages: each optimised for maximum performance Digital sources via USB, S/PDIF or Bluetooth Analogue sources via 4.4mm or 3.5mm inputs Brilliant Bluetooth. Hi-Res Wireless. Using the latest QCC 5100 series Bluetooth v5.1 as the starting point, for wireless connectivity, the xDSD Gryphon is at the bleeding-edge when it comes to the latest formats: aptX Adaptive and aptX HD LDAC and HWA/LHDC regular aptX and aptX Low Latency AAC SBC (plain vanilla Bluetooth) Not only this but the above is on the iFi digital platform where each section is distinct. So QC5100 for reception > Global Master Clock for jitter > Burr-Brown for DAC conversion. More effort but that’s why our wireless gives wired a run for its money. USB & S/PDIF. Wired to the nines. In terms of wired connectivity, the xDSD Gryphon handles all the formats using a hybrid Burr-Brown DAC chipset which is the same as used in our £3,000 flagship, the Pro iDSD Signature. Rest assured that all the following latest formats are catered for but most importantly, are pushed to their zenith. On USB: PCM (768/705.6/384/352.8/192/176.4/96/88.2/48/44.1 kHz) DSD (512/256/128/64) DXD (768/705.6/384/352.8kHz) MQA (Decoder) On S/PDIF PCM (192/176.4/96/88.2/48/44.1 kHz) DoP Balance of Power The xDSD Gryphon uses our PureWave amplification circuitry. It has 1,000mW at 32 Ohms. With a whopping max 6.7v output, bring on the high impedance headphones because the Gryphon will not break a sweat driving them. This is plenty to drive all manner of headphones. The 4.4mm Balanced is the best for balanced playback. The 3.5mm S-Balanced will max SE headphones. And your premium high-sensitivity IEMs have not been forgotten either – iEMatch will cut out the hiss. Tailored to your ears XSpace adds back the cavernous sound stage of recordings. XBass II reinstates the missing bass from open-backed headphones or for recordings that you hanker for bass slam. Under XBass II you can select ‘Bass’ and/or ‘Presence’ so that the upper midrange frequencies are correctly added back into your favourite recording. iEMatch – is our proprietary tech which reduces the annoying hiss from high-sensitivity headphones without losing any dynamic range. With digital sources, users can choose between three bespoke digital filters via the on-screen menu: Bit-Perfect, Standard and GTO (Gibbs Transient Optimised), each having a fine-tuning effect on sound. OLED. Seen but not heard. The OLED display and iFi’s CyberSync operating system combined, usher in a whole new world of user enjoyment – all information from format to battery life is there. Just as importantly, SilentLine technology means the display does not add noise into the system. It can even be set to off if preferred.
Liberty DAC is the Mytek most affordable, yet exceptional, PCM/MQA/DSD USB2 DAC designed for high quality music playback and monitoring of all digital audio formats including all high resolution formats. The DAC features several digital inputs, digital volume control and unbalanced as well as balanced audio outputs and a high performance headphone amplifier. Designed as a little brother of Brooklyn DAC, Liberty DAC provides robust performance in small portable 1/3 rack package.
52x more power. Pump up the volume. Laptops and smartphones have a really low power output of
The Uniti Atom Headphone Edition can transform any space into your own audio cocoon. Where typical headphone amplifiers demand tethering to a computer the Uniti Atom Headphone Edition has all the brains – and Naim’s exclusive streaming platform.
The Uniti Atom Headphone Edition can transform any space into your own audio cocoon. Where typical headphone amplifiers demand tethering to a computer the Uniti Atom Headphone Edition has all the brains – and Naim’s exclusive streaming platform.
Our entry model into the world of VOLTAiR headphone amplifiers. The Phonitor se has the same audio signal amplification as its bigger brothers Phonitor x and Phonitor xe and therefore offers the same sound experience. The DAC768xs is optionally available. Volume & Source Selection The volume is adjusted with a milled all-aluminium rotary knob. The Alps RK27 “Big Blue” potentiometer provides a pleasant “spoon in honey” turning feeling. In addition to an analog source, three other digital sources can be connected to the Phonitor se with the optional DAC. Headphone Output with Power The Phonitor se offers a 6.35 mm jack for connecting headphones with jack plug. Up to 2 x 5 watts of output power is available at this socket. This allows even very power-hungry headphones such as magnetostats or electrostats to be driven effortlessly. The Revolution in the headphone amplifier is the Phonitor Matrix, with switchable crossfeed, that allows you to listen to music through headphones with the sound experience of listening through speakers. The tiring super stereo effect and the exaggerated reproduction of reverberation and effects are a thing of the past. Enjoy your music without fatigue and exactly as it should be heard. The Phonitor Matrix in its largest expansion stage has three setting parameters: Crossfeed, Speaker Angle and Center Level.In Phonitor se the Center Level is preset to -1 dB and the speaker placement Angle to 30°. These are the most common values. The Crossfeed function determines the crosstalk of the channels, the so-called interaural level difference. There are two switch positions C1 and C2 for the intensity of the Crossfeed. Connections The Phonitor se is equipped with gold-plated RCA sockets for the analog input. The optional DAC768xs adds three more digital sources: USB Coax and Optical. The Optional DAC768xs The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the optional digital-to-analogue converter, which thanks to its new architecture reproduces the finest sound details. It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768kHz, which corresponds to 16 times the CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. Specifications: Analog input: RCA Maximum input gain: 32.5 dBu Input impedance: 20 kΩ Digital Inputs: DAC768xs (optional) Coaxial SPDIF (RCA), PCM sample rates: 44.1/48/88.2/96/176.4/192 kHz Optical SPDIF (Toslink F06), PCM sample rates: 44.1/48/88.2/96/with Glass fibre
Our entry model into the world of VOLTAiR headphone amplifiers. The Phonitor se has the same audio signal amplification as its bigger brothers Phonitor x and Phonitor xe and therefore offers the same sound experience. The DAC768xs is optionally available. Volume & Source Selection The volume is adjusted with a milled all-aluminium rotary knob. The Alps RK27 “Big Blue” potentiometer provides a pleasant “spoon in honey” turning feeling. In addition to an analog source, three other digital sources can be connected to the Phonitor se with the optional DAC. Headphone Output with Power The Phonitor se offers a 6.35 mm jack for connecting headphones with jack plug. Up to 2 x 5 watts of output power is available at this socket. This allows even very power-hungry headphones such as magnetostats or electrostats to be driven effortlessly. The Revolution in the headphone amplifier is the Phonitor Matrix, with switchable crossfeed, that allows you to listen to music through headphones with the sound experience of listening through speakers. The tiring super stereo effect and the exaggerated reproduction of reverberation and effects are a thing of the past. Enjoy your music without fatigue and exactly as it should be heard. The Phonitor Matrix in its largest expansion stage has three setting parameters: Crossfeed, Speaker Angle and Center Level.In Phonitor se the Center Level is preset to -1 dB and the speaker placement Angle to 30°. These are the most common values. The Crossfeed function determines the crosstalk of the channels, the so-called interaural level difference. There are two switch positions C1 and C2 for the intensity of the Crossfeed. Connections The Phonitor se is equipped with gold-plated RCA sockets for the analog input. The optional DAC768xs adds three more digital sources: USB Coax and Optical. The Optional DAC768xs The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the optional digital-to-analogue converter, which thanks to its new architecture reproduces the finest sound details. It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768kHz, which corresponds to 16 times the CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. Specifications: Analog input: RCA Maximum input gain: 32.5 dBu Input impedance: 20 kΩ Digital Inputs: DAC768xs (optional) Coaxial SPDIF (RCA), PCM sample rates: 44.1/48/88.2/96/176.4/192 kHz Optical SPDIF (Toslink F06), PCM sample rates: 44.1/48/88.2/96/with Glass fibre
Our entry model into the world of VOLTAiR headphone amplifiers. The Phonitor se has the same audio signal amplification as its bigger brothers Phonitor x and Phonitor xe and therefore offers the same sound experience. The DAC768xs is optionally available. Volume & Source Selection The volume is adjusted with a milled all-aluminium rotary knob. The Alps RK27 “Big Blue” potentiometer provides a pleasant “spoon in honey” turning feeling. In addition to an analog source, three other digital sources can be connected to the Phonitor se with the optional DAC. Headphone Output with Power The Phonitor se offers a 6.35 mm jack for connecting headphones with jack plug. Up to 2 x 5 watts of output power is available at this socket. This allows even very power-hungry headphones such as magnetostats or electrostats to be driven effortlessly. The Revolution in the headphone amplifier is the Phonitor Matrix, with switchable crossfeed, that allows you to listen to music through headphones with the sound experience of listening through speakers. The tiring super stereo effect and the exaggerated reproduction of reverberation and effects are a thing of the past. Enjoy your music without fatigue and exactly as it should be heard. The Phonitor Matrix in its largest expansion stage has three setting parameters: Crossfeed, Speaker Angle and Center Level.In Phonitor se the Center Level is preset to -1 dB and the speaker placement Angle to 30°. These are the most common values. The Crossfeed function determines the crosstalk of the channels, the so-called interaural level difference. There are two switch positions C1 and C2 for the intensity of the Crossfeed. Connections The Phonitor se is equipped with gold-plated RCA sockets for the analog input. The optional DAC768xs adds three more digital sources: USB Coax and Optical. The Optional DAC768xs The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the optional digital-to-analogue converter, which thanks to its new architecture reproduces the finest sound details. It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768kHz, which corresponds to 16 times the CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. Specifications: Analog input: RCA Maximum input gain: 32.5 dBu Input impedance: 20 kΩ Digital Inputs: DAC768xs (optional) Coaxial SPDIF (RCA), PCM sample rates: 44.1/48/88.2/96/176.4/192 kHz Optical SPDIF (Toslink F06), PCM sample rates: 44.1/48/88.2/96/with Glass fibre
With the new DAC768xs module, the Phonitor x really shows its phenomenal qualities as a headphone amplifier and preamp, even with digital sources connected.” The headphone amplifier with preamplifier Enjoy music over headphones and over speakers equally excellently with the superior VOLTAiR technology – that’s why we developed Phonitor x. For all headphones The Phonitor x offers connections for standard headphones with jack plug and for balanced headphones a 4-pin XLR connector. Thanks to the enormous output power of 18 watts, all headphones are driven effortlessly. To the power amplifiers or to the active loudspeakers you can use the balanced XLR- for long, and the RCA sockets for short cable runs. Practical are the AMP CTL sockets to which power amplifiers with 12V trigger inputs can be connected to switch them on and off together with Phonitor x. Milled from solid is the big 45mm Volume control. Its mass together with the motorized Alps RK27 “Big Blue” potentiometer enhances the “spoon in the honey” feeling even further. The red marker LED makes the setting visible even in darkened environments. Volume RC The volume can be remote controlled with any infrared remote control, that the Phonitor x simply learns. To do this, press the IR programming button and then the buttons for louder and quieter. Source of joy Up to six (6 !) stereo sources can be connected to Phonitor x: XLR, RCA, USB, Coax, Optical and AES/EBU Phonitor x accepts a large variety of audio connections. Balanced via XLR or unbalanced via RCA connectors. With the optional DAC768xs, three additional digital sources can be added. The DAC768xs The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the optional digital-to-analogue converter, which thanks to its new architecture reproduces the finest sound details. It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768kHz, which is equivalent to 16 times CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. Good ol' times Two mechanical VU meters visualize the input levels for the left and right audio channel. Finding the middle is not always easy. By our very nature, hearing can be leaning more to the left or more to the right. This is especially obvious when listening with headphones. That’s why Phonitor x has the uniquely finely resolved laterality control. With it, the center can be found perfectly. With the mode switch you can choose between stereo or mono playback. To the right, the laterality control is switched on. The Revolution in the headphone amplifier is the Phonitor Matrix, thanks to which you can listen to music through headphones as if you were listening through speakers. The tiring super stereo effect is a thing of the past. Enjoy your music exactly the way it should be heard. Specifications: Analog inputs & outputs: XLR (balanced) and RCA Maximum input & output gain: 32.5 dBu Input impedance (RCA): 20 kΩ Input impedance (XLR): 20 kΩ Output impedance: 75 kΩ Common mode rejection (XLR): 82 dB Frequency range (-3dB): 4 Hz – 300 kHz THD + N (10 Hz – 22 kHz, 0 dBu): 0.00085 % Noise (A-weighted): -103.8 dBu Crosstalk (1 kHz): -106 dB Dynamic range: 136.3 dB Digital Inputs: DAC768xs (optional) Coaxial SPDIF (RCA), PCM sample rates: 44.1/48/88.2/96/176.4/192 kHz Optical SPDIF (Toslink F06), PCM sample rates: 44.1/48/88.2/96/with Glass fibre
With innovative Phonitor Matrix, 32-bit DA-converter and outstanding sound quality. For us the sound is always in the foreground. When it sounds good, we like to listen. To get such a sound, you need experience and technical finesse. We have incorporated both into the Series One. The Preamplifier Stage Two Burr-Brown OPA 2134 SoundPlus™ operational amplifiers provide the pre-amplification. These are specially designed for audiophile circuits and are characterized by extremely low noise and minimal distortion of only 0.00008%.Thanks to a true FET stage, the OPA 2134 achieves a slew rate of 20V/µs, making it a high-speed operational amplifier. This has an immediate positive effect on the liveliness of the playback. In addition, low capacitance film capacitors are installed in the signal path as bypass capacitors of the coupling capacitors, which ensures a more precise transmission of the high-frequency signal components.The excellent Panasonic ‘Electric Double Layer’ gold electrolytic capacitors are used as coupling capacitors. They offer the highest storage capacity of all capacitor technologies.
For us the sound is always in the foreground. When it sounds good, we like to listen. To get such a sound, you need experience and technical finesse. We have incorporated both into the Series One. The Design Of The Amplification Stages Two Burr-Brown OPA 2134 SoundPlus™ operational amplifiers provide the pre-amplification. These are specially designed for audiophile circuits and are characterized by extremely low noise and minimal distortion of only 0.00008%. Thanks to a true FET stage, the OPA 2134 achieves a slew rate of 20V/µs, making it a high-speed operational amplifier. This has an immediate positive effect on the liveliness of the playback. In addition, low capacitance film capacitors are installed in the signal path as bypass capacitors of the coupling capacitors, which ensures a more precise transmission of the high-frequency signal components. The excellent Panasonic ‘Electric Double Layer’ gold electrolytic capacitors are used as coupling capacitors. They offer the highest storage capacity of all capacitor technologies.
Our nonplusultra headphone amplifier.The Phonitor xe is the nonplusultra standalone headphone amplifier without any compromises. Phonitor Matrix, remote volume control, retro-look VU meter, the optional premium DA converter and the all-superior VOLTAiR technology make the Phonitor xe one of the best headphone amplifiers of our time.Great Sound – for all headphonesThe Phonitor xe offers connections for a standard headphone with a stereo jack plug and for balanced-driven headphones using a 4 pin XLR plug.Thanks to the enormous output power, all headphones are driven effortlessly.Thus, it plays out the advantages of the SPL VOLTAiR technology and rewards the listener with an honest, detailed and at the same time vivid sound experience.Twice as niceThe Phonitor xe provides headphone outputs on the front and on the rear. On the front, you switch between F (front) and R (rear). This way, your favorite headphones remain firmly connected on the rear – without visible cabling on the front.Milled from solidThe massive 45mm volume control knob milled from aluminum is a haptic highlight. Its mass together with the motorized Alps RK27 “Big Blue” potentiometer enhances the “spoon in the honey” feeling even further.The red marker LED ensures good visibility of the volume parameter even in darkened environments.Remote controlThe volume control can be remotely controlled with any infrared remote control.The Phonitor xe learns to communicate with it with the simple push of a button.Learning made easyUsing Phonitor x as an example, this video explains how you can use any infrared remote control to remotely control the volume.Source of joyUp to six (6 !) stereo sources can be connected to the Phonitor xe:XLR, RCA and via the optional DAC768 also USB, COAX, OPTICAL and AES.Phonitor xe accepts almost all audio connections. Balanced via XLR or unbalanced via RCA connectors.With the optional DAC768, four additional digital sources are added. From USB to professional AES format, no wishes remain unfulfilled.The DAC automatically picks up the sampling rate and resolution of the digital playback source. No matter if a streamer, computer or CD player is connected. No further settings on the Phonitor xe are necessary.The DAC768The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the optional digital-to-analogue converter, which thanks to its architecture reproduces the finest sound details.It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768 kHz, which is equivalent to 16 times CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. In contrast to the DAC 768xs, the DAC768 not only offers an AES/EBU digital input, but also the SPL DLP120 with VOLTAiR technology.The DLP120 (Dual Low-Pass)The analog output of the DAC chip must be filtered by a low pass filter. Phonitor xe has two of them: One for PCM audio and one for DSD audio, since different roll-off frequencies are required.In contrast to all other DACs in the world, the low pass filters here are built using VOLTAiR technology, which provides a plus in dynamics and headroom and sound.Good ol' timesTwo mechanical VU meters visualize the input levels for the left and right audio channel.With the VU switch you can optimize the display for different signal levels.Finding the middleis not always easy. By our very nature, hearing can be leaning more to the left or more to the right. This is especially obvious when listening with headphones.That’s why Phonitor xe has the uniquely finely resolved laterality control. With it, the center can be found perfectly.With the MODE switch you can choose between stereo or mono playback. This switch also activates the laterality control.The Revolution: Phonitor MatrixThe Phonitor Matrix is the revolution in the headphone amplifier.Thanks to the Phonitor Matrix, music can be experienced on headphones as if it was played on speakers. The tiring super stereo effect is a thing of the past.Enjoy your music without listening fatigue and exactly the way it should be heard.Music is normally produced and mixed for playback on stereo speakers.Listening on headphones is different from listening on loudspeakers. The biggest difference is the lack of crossing signals of the sound signal from the left speaker to the right ear and from the right speaker to the left ear. These crossing signals are missing in conventional headphone listening, because there are no signals crossing from one side of the headphones to the other. This results in an unnaturally wide stereo image and the various sound sources of the audio signal are not localized as the sound engineer intended them to. This effect is often referred to as “super stereo effect”. During conventional listening on headphones, our brain can balance the false representation of the playback to a certain extent – but this is very exhausting.The SPL Phonitor Matrix can correct this false stereo image with an analog circuitry. The Phonitor Matrix therefore not only ensures a correct representation of the stereo image, but also a relaxed listening experience.The two main parameters of the Phonitor Matrix are Crossfeed and Angle:Crossfeed determines the crossing signals of the channels, the so-called interaural level difference.Angle determines the opening angle of the stereo image, the so-called interaural time difference.Center of AttentionTo make the listening experience even more perfect, the level of the center of the stereo image needs to be attenuated when the Phonitor Matrix is active. This ensures that not only the position of all sound sources is correct but also their volume.In the Professional Fidelity Phonitor devices this value is set to a fixed attenuation of -1 dB, which is the best choice for getting an authentic representation of the sound stage.Sounds good!With all devices of the Professional Fidelity series we develop not only according to plan, but also by ear. All important components are installed on the circuit boards using Through-hole technology. This way we can ensure that we can use the best sounding components.The VOLTAiR TechnologyThe 120V technology is our reference technology. The 120V technology is unique in the world. It operates at a DC voltage of 120 volts. This is four times that of IC-based semiconductor op-amps. In our Professional Fidelity series, we refer to this unsurpassed technology as VOLTAiR technology.The highest possible audio quality requires the highest possible audio operating voltage.The 120V technology works with +/-60 V. To be able to handle such a high voltage, we have developed special proprietary operational amplifiers that can operate with a DC voltage of +/-60 V: the SPL 120V SUPRA operational amplifiers. This high voltage would destroy conventional components and operational amplifiers.By the way, the “120V” in the name of the technology has nothing to do with the local mains voltage from the mains power socket. This is about the operating voltage inside the device with which the audio signals are processed.The mains voltage from the mains power socket is transformed to the required secondary voltage in the device’s internal linear power supply with toroidal transformer. Rectifiers convert this AC voltage into DC voltage required in the audio device.
Our nonplusultra headphone amplifier.The Phonitor xe is the nonplusultra standalone headphone amplifier without any compromises. Phonitor Matrix, remote volume control, retro-look VU meter, the optional premium DA converter and the all-superior VOLTAiR technology make the Phonitor xe one of the best headphone amplifiers of our time.Great Sound – for all headphonesThe Phonitor xe offers connections for a standard headphone with a stereo jack plug and for balanced-driven headphones using a 4 pin XLR plug.Thanks to the enormous output power, all headphones are driven effortlessly.Thus, it plays out the advantages of the SPL VOLTAiR technology and rewards the listener with an honest, detailed and at the same time vivid sound experience.Twice as niceThe Phonitor xe provides headphone outputs on the front and on the rear. On the front, you switch between F (front) and R (rear). This way, your favorite headphones remain firmly connected on the rear – without visible cabling on the front.Milled from solidThe massive 45mm volume control knob milled from aluminum is a haptic highlight. Its mass together with the motorized Alps RK27 “Big Blue” potentiometer enhances the “spoon in the honey” feeling even further.The red marker LED ensures good visibility of the volume parameter even in darkened environments.Remote controlThe volume control can be remotely controlled with any infrared remote control.The Phonitor xe learns to communicate with it with the simple push of a button.Learning made easyUsing Phonitor x as an example, this video explains how you can use any infrared remote control to remotely control the volume.Source of joyUp to six (6 !) stereo sources can be connected to the Phonitor xe:XLR, RCA and via the optional DAC768 also USB, COAX, OPTICAL and AES.Phonitor xe accepts almost all audio connections. Balanced via XLR or unbalanced via RCA connectors.With the optional DAC768, four additional digital sources are added. From USB to professional AES format, no wishes remain unfulfilled.The DAC automatically picks up the sampling rate and resolution of the digital playback source. No matter if a streamer, computer or CD player is connected. No further settings on the Phonitor xe are necessary.The DAC768The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the optional digital-to-analogue converter, which thanks to its architecture reproduces the finest sound details.It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768 kHz, which is equivalent to 16 times CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. In contrast to the DAC 768xs, the DAC768 not only offers an AES/EBU digital input, but also the SPL DLP120 with VOLTAiR technology.The DLP120 (Dual Low-Pass)The analog output of the DAC chip must be filtered by a low pass filter. Phonitor xe has two of them: One for PCM audio and one for DSD audio, since different roll-off frequencies are required.In contrast to all other DACs in the world, the low pass filters here are built using VOLTAiR technology, which provides a plus in dynamics and headroom and sound.Good ol' timesTwo mechanical VU meters visualize the input levels for the left and right audio channel.With the VU switch you can optimize the display for different signal levels.Finding the middleis not always easy. By our very nature, hearing can be leaning more to the left or more to the right. This is especially obvious when listening with headphones.That’s why Phonitor xe has the uniquely finely resolved laterality control. With it, the center can be found perfectly.With the MODE switch you can choose between stereo or mono playback. This switch also activates the laterality control.The Revolution: Phonitor MatrixThe Phonitor Matrix is the revolution in the headphone amplifier.Thanks to the Phonitor Matrix, music can be experienced on headphones as if it was played on speakers. The tiring super stereo effect is a thing of the past.Enjoy your music without listening fatigue and exactly the way it should be heard.Music is normally produced and mixed for playback on stereo speakers.Listening on headphones is different from listening on loudspeakers. The biggest difference is the lack of crossing signals of the sound signal from the left speaker to the right ear and from the right speaker to the left ear. These crossing signals are missing in conventional headphone listening, because there are no signals crossing from one side of the headphones to the other. This results in an unnaturally wide stereo image and the various sound sources of the audio signal are not localized as the sound engineer intended them to. This effect is often referred to as “super stereo effect”. During conventional listening on headphones, our brain can balance the false representation of the playback to a certain extent – but this is very exhausting.The SPL Phonitor Matrix can correct this false stereo image with an analog circuitry. The Phonitor Matrix therefore not only ensures a correct representation of the stereo image, but also a relaxed listening experience.The two main parameters of the Phonitor Matrix are Crossfeed and Angle:Crossfeed determines the crossing signals of the channels, the so-called interaural level difference.Angle determines the opening angle of the stereo image, the so-called interaural time difference.Center of AttentionTo make the listening experience even more perfect, the level of the center of the stereo image needs to be attenuated when the Phonitor Matrix is active. This ensures that not only the position of all sound sources is correct but also their volume.In the Professional Fidelity Phonitor devices this value is set to a fixed attenuation of -1 dB, which is the best choice for getting an authentic representation of the sound stage.Sounds good!With all devices of the Professional Fidelity series we develop not only according to plan, but also by ear. All important components are installed on the circuit boards using Through-hole technology. This way we can ensure that we can use the best sounding components.The VOLTAiR TechnologyThe 120V technology is our reference technology. The 120V technology is unique in the world. It operates at a DC voltage of 120 volts. This is four times that of IC-based semiconductor op-amps. In our Professional Fidelity series, we refer to this unsurpassed technology as VOLTAiR technology.The highest possible audio quality requires the highest possible audio operating voltage.The 120V technology works with +/-60 V. To be able to handle such a high voltage, we have developed special proprietary operational amplifiers that can operate with a DC voltage of +/-60 V: the SPL 120V SUPRA operational amplifiers. This high voltage would destroy conventional components and operational amplifiers.By the way, the “120V” in the name of the technology has nothing to do with the local mains voltage from the mains power socket. This is about the operating voltage inside the device with which the audio signals are processed.The mains voltage from the mains power socket is transformed to the required secondary voltage in the device’s internal linear power supply with toroidal transformer. Rectifiers convert this AC voltage into DC voltage required in the audio device.
The headphone amplifier with preamplifier Enjoy music over headphones and over speakers equally excellently with the superior VOLTAiR technology – that’s why we developed Phonitor x. For all headphones The Phonitor x offers connections for standard headphones with jack plug and for balanced headphones a 4-pin XLR connector. Thanks to the enormous output power of 18 watts, all headphones are driven effortlessly. To the power amplifiers or to the active loudspeakers you can use the balanced XLR- for long, and the RCA sockets for short cable runs. Practical are the AMP CTL sockets to which power amplifiers with 12V trigger inputs can be connected to switch them on and off together with Phonitor x. Milled from solid is the big 45mm Volume control. Its mass together with the motorized Alps RK27 “Big Blue” potentiometer enhances the “spoon in the honey” feeling even further. The red marker LED makes the setting visible even in darkened environments. Volume RC The volume can be remote controlled with any infrared remote control, that the Phonitor x simply learns. To do this, press the IR programming button and then the buttons for louder and quieter. Source of joy Up to six (6 !) stereo sources can be connected to Phonitor x: XLR, RCA, USB, Coax, Optical and AES/EBU Phonitor x accepts a large variety of audio connections. Balanced via XLR or unbalanced via RCA connectors. With the optional DAC768xs, three additional digital sources can be added. The DAC768xs The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the optional digital-to-analogue converter, which thanks to its new architecture reproduces the finest sound details. It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768kHz, which is equivalent to 16 times CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. Good ol' times Two mechanical VU meters visualize the input levels for the left and right audio channel. Finding the middle is not always easy. By our very nature, hearing can be leaning more to the left or more to the right. This is especially obvious when listening with headphones. That’s why Phonitor x has the uniquely finely resolved laterality control. With it, the center can be found perfectly. With the mode switch you can choose between stereo or mono playback. To the right, the laterality control is switched on. The Revolution in the headphone amplifier is the Phonitor Matrix, thanks to which you can listen to music through headphones as if you were listening through speakers. The tiring super stereo effect is a thing of the past. Enjoy your music exactly the way it should be heard. Specifications: Analog inputs & outputs: XLR (balanced) and RCA Maximum input & output gain: 32.5 dBu Input impedance (RCA): 20 kΩ Input impedance (XLR): 20 kΩ Output impedance: 75 kΩ Common mode rejection (XLR): 82 dB Frequency range (-3dB): 4 Hz – 300 kHz THD + N (10 Hz – 22 kHz, 0 dBu): 0.00085 % Noise (A-weighted): -103.8 dBu Crosstalk (1 kHz): -106 dB Dynamic range: 136.3 dB Digital Inputs: DAC768xs (optional) Coaxial SPDIF (RCA), PCM sample rates: 44.1/48/88.2/96/176.4/192 kHz Optical SPDIF (Toslink F06), PCM sample rates: 44.1/48/88.2/96/with Glass fibre
The headphone amplifier with preamplifier Enjoy music over headphones and over speakers equally excellently with the superior VOLTAiR technology – that’s why we developed Phonitor x. For all headphones The Phonitor x offers connections for standard headphones with jack plug and for balanced headphones a 4-pin XLR connector. Thanks to the enormous output power of 18 watts, all headphones are driven effortlessly. To the power amplifiers or to the active loudspeakers you can use the balanced XLR- for long, and the RCA sockets for short cable runs. Practical are the AMP CTL sockets to which power amplifiers with 12V trigger inputs can be connected to switch them on and off together with Phonitor x. Milled from solid is the big 45mm Volume control. Its mass together with the motorized Alps RK27 “Big Blue” potentiometer enhances the “spoon in the honey” feeling even further. The red marker LED makes the setting visible even in darkened environments. Volume RC The volume can be remote controlled with any infrared remote control, that the Phonitor x simply learns. To do this, press the IR programming button and then the buttons for louder and quieter. Source of joy Up to six (6 !) stereo sources can be connected to Phonitor x: XLR, RCA, USB, Coax, Optical and AES/EBU Phonitor x accepts a large variety of audio connections. Balanced via XLR or unbalanced via RCA connectors. With the optional DAC768xs, three additional digital sources can be added. The DAC768xs The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the optional digital-to-analogue converter, which thanks to its new architecture reproduces the finest sound details. It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768kHz, which is equivalent to 16 times CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. Good ol' times Two mechanical VU meters visualize the input levels for the left and right audio channel. Finding the middle is not always easy. By our very nature, hearing can be leaning more to the left or more to the right. This is especially obvious when listening with headphones. That’s why Phonitor x has the uniquely finely resolved laterality control. With it, the center can be found perfectly. With the mode switch you can choose between stereo or mono playback. To the right, the laterality control is switched on. The Revolution in the headphone amplifier is the Phonitor Matrix, thanks to which you can listen to music through headphones as if you were listening through speakers. The tiring super stereo effect is a thing of the past. Enjoy your music exactly the way it should be heard. Specifications: Analog inputs & outputs: XLR (balanced) and RCA Maximum input & output gain: 32.5 dBu Input impedance (RCA): 20 kΩ Input impedance (XLR): 20 kΩ Output impedance: 75 kΩ Common mode rejection (XLR): 82 dB Frequency range (-3dB): 4 Hz – 300 kHz THD + N (10 Hz – 22 kHz, 0 dBu): 0.00085 % Noise (A-weighted): -103.8 dBu Crosstalk (1 kHz): -106 dB Dynamic range: 136.3 dB Digital Inputs: DAC768xs (optional) Coaxial SPDIF (RCA), PCM sample rates: 44.1/48/88.2/96/176.4/192 kHz Optical SPDIF (Toslink F06), PCM sample rates: 44.1/48/88.2/96/with Glass fibre
Our nonplusultra headphone amplifier.The Phonitor xe is the nonplusultra standalone headphone amplifier without any compromises. Phonitor Matrix, remote volume control, retro-look VU meter, the optional premium DA converter and the all-superior VOLTAiR technology make the Phonitor xe one of the best headphone amplifiers of our time.Great Sound – for all headphonesThe Phonitor xe offers connections for a standard headphone with a stereo jack plug and for balanced-driven headphones using a 4 pin XLR plug.Thanks to the enormous output power, all headphones are driven effortlessly.Thus, it plays out the advantages of the SPL VOLTAiR technology and rewards the listener with an honest, detailed and at the same time vivid sound experience.Twice as niceThe Phonitor xe provides headphone outputs on the front and on the rear. On the front, you switch between F (front) and R (rear). This way, your favorite headphones remain firmly connected on the rear – without visible cabling on the front.Milled from solidThe massive 45mm volume control knob milled from aluminum is a haptic highlight. Its mass together with the motorized Alps RK27 “Big Blue” potentiometer enhances the “spoon in the honey” feeling even further.The red marker LED ensures good visibility of the volume parameter even in darkened environments.Remote controlThe volume control can be remotely controlled with any infrared remote control.The Phonitor xe learns to communicate with it with the simple push of a button.Learning made easyUsing Phonitor x as an example, this video explains how you can use any infrared remote control to remotely control the volume.Source of joyUp to six (6 !) stereo sources can be connected to the Phonitor xe:XLR, RCA and via the optional DAC768 also USB, COAX, OPTICAL and AES.Phonitor xe accepts almost all audio connections. Balanced via XLR or unbalanced via RCA connectors.With the optional DAC768, four additional digital sources are added. From USB to professional AES format, no wishes remain unfulfilled.The DAC automatically picks up the sampling rate and resolution of the digital playback source. No matter if a streamer, computer or CD player is connected. No further settings on the Phonitor xe are necessary.The DAC768The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the optional digital-to-analogue converter, which thanks to its architecture reproduces the finest sound details.It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768 kHz, which is equivalent to 16 times CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. In contrast to the DAC 768xs, the DAC768 not only offers an AES/EBU digital input, but also the SPL DLP120 with VOLTAiR technology.The DLP120 (Dual Low-Pass)The analog output of the DAC chip must be filtered by a low pass filter. Phonitor xe has two of them: One for PCM audio and one for DSD audio, since different roll-off frequencies are required.In contrast to all other DACs in the world, the low pass filters here are built using VOLTAiR technology, which provides a plus in dynamics and headroom and sound.Good ol' timesTwo mechanical VU meters visualize the input levels for the left and right audio channel.With the VU switch you can optimize the display for different signal levels.Finding the middleis not always easy. By our very nature, hearing can be leaning more to the left or more to the right. This is especially obvious when listening with headphones.That’s why Phonitor xe has the uniquely finely resolved laterality control. With it, the center can be found perfectly.With the MODE switch you can choose between stereo or mono playback. This switch also activates the laterality control.The Revolution: Phonitor MatrixThe Phonitor Matrix is the revolution in the headphone amplifier.Thanks to the Phonitor Matrix, music can be experienced on headphones as if it was played on speakers. The tiring super stereo effect is a thing of the past.Enjoy your music without listening fatigue and exactly the way it should be heard.Music is normally produced and mixed for playback on stereo speakers.Listening on headphones is different from listening on loudspeakers. The biggest difference is the lack of crossing signals of the sound signal from the left speaker to the right ear and from the right speaker to the left ear. These crossing signals are missing in conventional headphone listening, because there are no signals crossing from one side of the headphones to the other. This results in an unnaturally wide stereo image and the various sound sources of the audio signal are not localized as the sound engineer intended them to. This effect is often referred to as “super stereo effect”. During conventional listening on headphones, our brain can balance the false representation of the playback to a certain extent – but this is very exhausting.The SPL Phonitor Matrix can correct this false stereo image with an analog circuitry. The Phonitor Matrix therefore not only ensures a correct representation of the stereo image, but also a relaxed listening experience.The two main parameters of the Phonitor Matrix are Crossfeed and Angle:Crossfeed determines the crossing signals of the channels, the so-called interaural level difference.Angle determines the opening angle of the stereo image, the so-called interaural time difference.Center of AttentionTo make the listening experience even more perfect, the level of the center of the stereo image needs to be attenuated when the Phonitor Matrix is active. This ensures that not only the position of all sound sources is correct but also their volume.In the Professional Fidelity Phonitor devices this value is set to a fixed attenuation of -1 dB, which is the best choice for getting an authentic representation of the sound stage.Sounds good!With all devices of the Professional Fidelity series we develop not only according to plan, but also by ear. All important components are installed on the circuit boards using Through-hole technology. This way we can ensure that we can use the best sounding components.The VOLTAiR TechnologyThe 120V technology is our reference technology. The 120V technology is unique in the world. It operates at a DC voltage of 120 volts. This is four times that of IC-based semiconductor op-amps. In our Professional Fidelity series, we refer to this unsurpassed technology as VOLTAiR technology.The highest possible audio quality requires the highest possible audio operating voltage.The 120V technology works with +/-60 V. To be able to handle such a high voltage, we have developed special proprietary operational amplifiers that can operate with a DC voltage of +/-60 V: the SPL 120V SUPRA operational amplifiers. This high voltage would destroy conventional components and operational amplifiers.By the way, the “120V” in the name of the technology has nothing to do with the local mains voltage from the mains power socket. This is about the operating voltage inside the device with which the audio signals are processed.The mains voltage from the mains power socket is transformed to the required secondary voltage in the device’s internal linear power supply with toroidal transformer. Rectifiers convert this AC voltage into DC voltage required in the audio device.
Our entry model into the world of VOLTAiR headphone amplifiers. The Phonitor se has the same audio signal amplification as its bigger brothers Phonitor x and Phonitor xe and therefore offers the same sound experience. The DAC768xs is optionally available. Volume & Source Selection The volume is adjusted with a milled all-aluminium rotary knob. The Alps RK27 “Big Blue” potentiometer provides a pleasant “spoon in honey” turning feeling. In addition to an analog source, three other digital sources can be connected to the Phonitor se with the optional DAC. Headphone Output with Power The Phonitor se offers a 6.35 mm jack for connecting headphones with jack plug. Up to 2 x 5 watts of output power is available at this socket. This allows even very power-hungry headphones such as magnetostats or electrostats to be driven effortlessly. The Revolution in the headphone amplifier is the Phonitor Matrix, with switchable crossfeed, that allows you to listen to music through headphones with the sound experience of listening through speakers. The tiring super stereo effect and the exaggerated reproduction of reverberation and effects are a thing of the past. Enjoy your music without fatigue and exactly as it should be heard. The Phonitor Matrix in its largest expansion stage has three setting parameters: Crossfeed, Speaker Angle and Center Level.In Phonitor se the Center Level is preset to -1 dB and the speaker placement Angle to 30°. These are the most common values. The Crossfeed function determines the crosstalk of the channels, the so-called interaural level difference. There are two switch positions C1 and C2 for the intensity of the Crossfeed. Connections The Phonitor se is equipped with gold-plated RCA sockets for the analog input. The optional DAC768xs adds three more digital sources: USB Coax and Optical. The Optional DAC768xs The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the optional digital-to-analogue converter, which thanks to its new architecture reproduces the finest sound details. It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768kHz, which corresponds to 16 times the CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. Specifications: Analog input: RCA Maximum input gain: 32.5 dBu Input impedance: 20 kΩ Digital Inputs: DAC768xs (optional) Coaxial SPDIF (RCA), PCM sample rates: 44.1/48/88.2/96/176.4/192 kHz Optical SPDIF (Toslink F06), PCM sample rates: 44.1/48/88.2/96/with Glass fibre
All essential functions in a stylish, slim housing. The Phonitor e offers Phonitor Matrix, volume remote control, connection also for balanced headphones, DA converter option and the all superior VOLTAiR technology. For all headphones The Phonitor e offers connections for standard headphones with jack plug and for balanced headphones a 4-pin XLR connector. Thanks to the high output power, all headphones are driven effortlessly. Volume with remote control The volume is adjusted with a milled all-aluminium rotary knob. The Alps RK27 “Big Blue” potentiometer provides a pleasant “spoon in honey” turning feeling. The volume can be adjusted with any infrared remote control. The Phonitor e learns their commands. To do this, press the IR programming button on the back and then the buttons for louder and softer. Source selection A total of five sources can be connected to Phonitor e: XLR, Cinch, USB, Coax, and Optical Phonitor e is equipped with RCA connectors and balanced XLR connectors for the analog inputs. The optional DAC768xs adds three more digital sources: USB, Coax and Optical. The optional DAC768xs The converter chip used in the optional digital-to-analog converter is the highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip, which thanks to its new architecture reproduces the finest sound details. It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768kHz, which corresponds to 16 times the CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. The Revolution in the headphone amplifier is the Phonitor Matrix, with switchable crossfeed, thanks to which you can listen to music with headphones as if you are listening to speakers. The tiring super stereo effect and the exaggerated reproduction of reverberation rooms and effects are a thing of the past. Enjoy your music without tiring and exactly as it should be heard. The Phonitor Matrix, in its largest expansion stage, has three adjustment parameters: Crossfeed, Speaker Angle and Center Level. In Phonitor e the center level is preset to -1 dB and the speaker angle to 30°. These are the most common values. The crossfeed function determines the crosstalk of the channels, the so-called interaural level difference. There are two switch positions C1 and C2 for the intensity of the crossfeed. Specifications: Analog Inputs: XLR (balanced), RCA Maximum input gain: 32.5 dBu Input impedance: 20 kΩ Digital Inputs: DAC768xs (optional) Coaxial SPDIF (RCA), PCM sample rates: 44.1/48/88.2/96/176.4/192 kHz Optical SPDIF (Toslink F06), PCM sample rates: 44.1/48/88.2/96/with Glass fibre
All essential functions in a stylish, slim housing. The Phonitor e offers Phonitor Matrix, volume remote control, connection also for balanced headphones, DA converter option and the all superior VOLTAiR technology. For all headphones The Phonitor e offers connections for standard headphones with jack plug and for balanced headphones a 4-pin XLR connector. Thanks to the high output power, all headphones are driven effortlessly. Volume with remote control The volume is adjusted with a milled all-aluminium rotary knob. The Alps RK27 “Big Blue” potentiometer provides a pleasant “spoon in honey” turning feeling. The volume can be adjusted with any infrared remote control. The Phonitor e learns their commands. To do this, press the IR programming button on the back and then the buttons for louder and softer. Source selection A total of five sources can be connected to Phonitor e: XLR, Cinch, USB, Coax, and Optical Phonitor e is equipped with RCA connectors and balanced XLR connectors for the analog inputs. The optional DAC768xs adds three more digital sources: USB, Coax and Optical. The optional DAC768xs The converter chip used in the optional digital-to-analog converter is the highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip, which thanks to its new architecture reproduces the finest sound details. It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768kHz, which corresponds to 16 times the CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. The Revolution in the headphone amplifier is the Phonitor Matrix, with switchable crossfeed, thanks to which you can listen to music with headphones as if you are listening to speakers. The tiring super stereo effect and the exaggerated reproduction of reverberation rooms and effects are a thing of the past. Enjoy your music without tiring and exactly as it should be heard. The Phonitor Matrix, in its largest expansion stage, has three adjustment parameters: Crossfeed, Speaker Angle and Center Level. In Phonitor e the center level is preset to -1 dB and the speaker angle to 30°. These are the most common values. The crossfeed function determines the crosstalk of the channels, the so-called interaural level difference. There are two switch positions C1 and C2 for the intensity of the crossfeed. Specifications: Analog Inputs: XLR (balanced), RCA Maximum input gain: 32.5 dBu Input impedance: 20 kΩ Digital Inputs: DAC768xs (optional) Coaxial SPDIF (RCA), PCM sample rates: 44.1/48/88.2/96/176.4/192 kHz Optical SPDIF (Toslink F06), PCM sample rates: 44.1/48/88.2/96/with Glass fibre
Our entry model into the world of VOLTAiR headphone amplifiers. The Phonitor se has the same audio signal amplification as its bigger brothers Phonitor x and Phonitor xe and therefore offers the same sound experience. The DAC768xs is optionally available. Volume & Source Selection The volume is adjusted with a milled all-aluminium rotary knob. The Alps RK27 “Big Blue” potentiometer provides a pleasant “spoon in honey” turning feeling. In addition to an analog source, three other digital sources can be connected to the Phonitor se with the optional DAC. Headphone Output with Power The Phonitor se offers a 6.35 mm jack for connecting headphones with jack plug. Up to 2 x 5 watts of output power is available at this socket. This allows even very power-hungry headphones such as magnetostats or electrostats to be driven effortlessly. The Revolution in the headphone amplifier is the Phonitor Matrix, with switchable crossfeed, that allows you to listen to music through headphones with the sound experience of listening through speakers. The tiring super stereo effect and the exaggerated reproduction of reverberation and effects are a thing of the past. Enjoy your music without fatigue and exactly as it should be heard. The Phonitor Matrix in its largest expansion stage has three setting parameters: Crossfeed, Speaker Angle and Center Level.In Phonitor se the Center Level is preset to -1 dB and the speaker placement Angle to 30°. These are the most common values. The Crossfeed function determines the crosstalk of the channels, the so-called interaural level difference. There are two switch positions C1 and C2 for the intensity of the Crossfeed. Connections The Phonitor se is equipped with gold-plated RCA sockets for the analog input. The optional DAC768xs adds three more digital sources: USB Coax and Optical. The Optional DAC768xs The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the optional digital-to-analogue converter, which thanks to its new architecture reproduces the finest sound details. It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768kHz, which corresponds to 16 times the CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. Specifications: Analog input: RCA Maximum input gain: 32.5 dBu Input impedance: 20 kΩ Digital Inputs: DAC768xs (optional) Coaxial SPDIF (RCA), PCM sample rates: 44.1/48/88.2/96/176.4/192 kHz Optical SPDIF (Toslink F06), PCM sample rates: 44.1/48/88.2/96/with Glass fibre
The headphone monitoring amp and preamplifier with Phonitor Matrix. Phonitor 2 is the ultimate headphone amplifier for sound and mastering engineers who also mix and master on headphones. Speakers can also be connected, making Phonitor 2 a full-fledged monitor controller. Milled from the solid aluminum is the 45mm large volume knob. Its mass in combination with the motorized Alps RK27 “Big Blue” potentiometer further enhances the “spoon in honey” turning feeling. Remote control The volume can be adjusted with any infrared remote control, which Phonitor 2 simply learns. Just press the IR programming button on the back and then the buttons for louder and softer. Learning made easy This video explains how you can use any infrared remote control to remotely control the volume. Monitor Controller Features Sources: 2x XLR, 1x RCA Solo L/R Phase reversal for L and R Output switchable to headphones or speakers Mute Phonitor Matrix with crossfeed, speaker angle and center level (the latter can be switched off) To The Power Amp or to the active loudspeakers it goes symmetrically via XLR sockets. Slave Thru The volume control can be switched off by means of a dip-switch on the bottom of the unit. The Sources Two balanced and one unbalanced stereo sources can be connected to Phonitor 2. If a CD player or other HiFi equipment is connected to the RCA jacks, the consumer level can be raised from -10 dBV to 0 dBu using a dip switch on the bottom of the unit. In this way the sources are comparable in level. Mechanical VU Meter visualize the input levels, which can be switched in sensitivity with the VU Cal switch. Laterality By its very nature, hearing can be directed more to the left or more to the right. This is particularly evident when listening with headphones. That’s why Phonitor 2 has the finely resolved Laterality control. With it the center can be set perfectly. The Revolution in the headphone amplifier is the Phonitor Matrix, thanks to which you can create and evaluate your production through headphones in the same way as through speakers. To achieve this, the super stereo effect must be corrected. It makes the placement of voices and instruments in the stereo image appear to be more widely distributed and effects like reverb and delays are overdone.
Designed and manufactured in the United Kingdom, CALLIA embodies the Prism Sound uncompromising approach to audio resulting in the most accurate and detailed DAC available. Callia reveals the most minute nuance of any performance and is flexible in the face of a variety of genres. Hear your music the way it was intended. PRISTINE SOUND QUALITY Callia makes no compromises on audio quality, ensuring you’ll experience music at home exactly as it was experienced by those who created it in the studio. Our heritage and unrivaled experience has allowed for the creation of a DAC of unparalleled sonic clarity. HEADPHONE OUTPUT CALLIA’s headphone output boasts a high-current, low impedance design optimized for the best possible performance. Able to power a wide range of high end headphones, CALLIA will adjust and match the impedance of your headphones for an unbeatable listening experience. SIMPLIFIED CONNECTIVITY Callia is compatible with the widest range of computer hardware using a USB2 interface supporting UAC2 audio. Auto input detection and output protection allows for the hot plugging of cables without fear of damaging your speakers. UNSURPASSED CLOCKING AND JITTER REJECTION Prism Sounds long history in developing test and measurement equipment for the audio industry has provided Callia with the pinnacle of ultra-stable clocks, ensuring the most accurate and detailed conversion available. AUDIO FORMATS CALLIA supports linear PCM in 2’s complement binary coding and, using the “DSD over PCM” (DOP) protocol, DSD at the original bit-rate (DSD64) and also at 2 x the original rate (DSD128). DSD Files encoded as “DOP” may be played with both ASIO and WDM drivers. Your computer, tablet or transport will commonly decode formats such as mp3 to PCM prior to transmission to the sound card, so these formats will typically be supported on your device in the same manner as they would be with another sound card. On the S/P-DIF inputs, DOP can also be used, but only at the original DSD bit rate (DSD64) as these connections do not have enough bandwidth for DSD128. The ASIO native DSD format is not currently supported. Specifications: Dimensions: Table-top (including feet): 285 x 242 x 50mm Power: 90VAC – 250VAC, 50 – 60Hz 15W consumption 0.5A(T), 20mm, glass Inputs: 1 x USB Audio Device Class 2.0 1 x TOSLINK for S/PDIF 1 x RCA for AES3-ID Outputs: 2 x XLR (balanced) 2 x RCA (pseudo-balanced)
Brooklyn is a reference USB2 DAC, line and phono analog preamplifier and a reference headphone amplifier.It integrates digital and vinyl hi-res playback for reference listening on headphones and speakers.SPECIFICATIONS :CONVERSION: up to 384k, 32bit PCM, native DSDup to DSD256,DXD, 130dB Dynamic RangeMQA HI-RES DECODER: built in certified hardwareMQA™ decoder DIGITAL INPUTS: USB2 Class2 (OSX, Linux driverless,all formats), AES/EBU (PCM up to 192k, up to DSD64 DOP), 2x S/PDIF (PCM up to 192k, up to DSD64 DOP), Toslink/ADAT 2x S/PDIF (PCM up to 192k, up to DSD64 DOP), SDIF3 DSD up to DSD256CLOCK: “Mytek Femtoclock Generator™” 0.82ps internal jitter, Wordclock Input and Output (allows stacking multiple units for multichannel operation,includesmch DSD)ANALOG OUTPUTS: RCA, balanced XLR, simultaneous,50 Ohm impedanceHEADPHONE OUTPUTS: Reference High Current,High transient Headphone Amp, 500mA, 6 Watts,dual headphone jacks, designed to drive hard todrive headphones. BUILT-IN ATTENUATOR: Choice of 1dB step analog attenuator, separate for main out and head- phones,1dB step digital32 bit attenuator and purist relay bypass.BUILT-IN ANALOG PREAMP: Line level input orPhono M/M, M/C input, relay controlled. AUDIO INTERFACE FUNCTION: All digital inputs canberoutedinto computer via USB2. Allows connectionof external digital sources such as CD Players anddigitizing ADCs.REMOTE: Included, universal remote capableFIRMWARE: Upgradable via USB Control panelWORLDWIDE POWER SUPPLYOPTIONAL DC/BATTERY POWER INPUT: 12VDCDIMENSIONS: WxDxH=8.5x8.5x1.74”=216x216x44mmWEIGHT: 4lbs, 2kgWARRANTY: 2 years
Musical Fidelity has extensive experience making super headphone amps, the LX2-HPA builds on our decades of experience to deliver a great performer with beautiful, restrained and tasteful aesthetics. Technical PerformanceA headphone amplifier is like a small power amp, relative to the load (the headphones) the technical requirements are similar: Excellent load tolerance, high stability margins, low distortion, wide bandwidth, low noise, excellent channel separation.The LX2-HPA will easily drive any commercially produced headphone. It's high current delivery and excellent stability margins result in completely uncoloured neutral performance.Distortion at less than 0.0035%, wide band is vanishingly low and certainly inaudible.Bandwidth extends to about 80kHz and even at 40kHz the distortion remains well below 0.05%. A remarkable achievement.The outstanding noise ratio of better than 112dB means that the music comes from a true 'black velvet' background field.Stereo separation is excellent and assures a rock solid imaging experience. Talk about 'adventures in inner space! OverallThe LX2-HPA gives a sensual monitor level listening experience. Completely uncoloured sound delivered with virtually limitless dynamic range from a black velvet background, and perfectly placed spatial imagery. Technical Specifications:SpecificationsInput Impedance: 47KΩInput Sensitivity: 3.0mVTotal Harmonic Distortion: 0.01%Signal / Noise Ratio: >80dBGeneralPower Requirement: 12 - 24V 100mA RegulatedConnectionsRCA Input: 1pr RCA socketsRCA Output: 1pr RCA socketsHeadphone Output (6.3mm): 1 stereo jack socket (6.3mm)Headphone Output (3.5mm): 1 stereo jack socket (3.5mm)Power Input: DC Jack (1.3mm inner pin, outer diam. 3.5mmDimensionsLength (including terminals) 197mmWidth 172mmHeight (including feet) 46.5 mmWeightUnit alone: 1.05KgUnit with packing: 1.50KgIncluded accessoriesPower Supply: 12V 500mA
Musical Fidelity has extensive experience making super headphone amps, the LX2-HPA builds on our decades of experience to deliver a great performer with beautiful, restrained and tasteful aesthetics. Technical PerformanceA headphone amplifier is like a small power amp, relative to the load (the headphones) the technical requirements are similar: Excellent load tolerance, high stability margins, low distortion, wide bandwidth, low noise, excellent channel separation.The LX2-HPA will easily drive any commercially produced headphone. It's high current delivery and excellent stability margins result in completely uncoloured neutral performance.Distortion at less than 0.0035%, wide band is vanishingly low and certainly inaudible.Bandwidth extends to about 80kHz and even at 40kHz the distortion remains well below 0.05%. A remarkable achievement.The outstanding noise ratio of better than 112dB means that the music comes from a true 'black velvet' background field.Stereo separation is excellent and assures a rock solid imaging experience. Talk about 'adventures in inner space! OverallThe LX2-HPA gives a sensual monitor level listening experience. Completely uncoloured sound delivered with virtually limitless dynamic range from a black velvet background, and perfectly placed spatial imagery. Technical Specifications:SpecificationsInput Impedance: 47KΩInput Sensitivity: 3.0mVTotal Harmonic Distortion: 0.01%Signal / Noise Ratio: >80dBGeneralPower Requirement: 12 - 24V 100mA RegulatedConnectionsRCA Input: 1pr RCA socketsRCA Output: 1pr RCA socketsHeadphone Output (6.3mm): 1 stereo jack socket (6.3mm)Headphone Output (3.5mm): 1 stereo jack socket (3.5mm)Power Input: DC Jack (1.3mm inner pin, outer diam. 3.5mmDimensionsLength (including terminals) 197mmWidth 172mmHeight (including feet) 46.5 mmWeightUnit alone: 1.05KgUnit with packing: 1.50KgIncluded accessoriesPower Supply: 12V 500mA
Problem: A performer needs to hear him/herself through headphones exclusively or mixed with the output of a mixer, CD player, tape deck, or other stereo line level source. Only the mic signal, however, should be going to the main mixer.Solution: Connect MyMONITOR between the mic and line source, and the mixer. The Mic and line Monitor levels can then be adjusted for mix and volume through the headphones. Only the mic signal will go to the board. And since MyMONITOR can be AC or battery powered, the unit can be used on a large stage or wherever there is no AC outlet nearby. Dynamic or condenser mics can be used since phantom power would come through the Mic Thru jack from the mixer or other source.Specifications:Maximum Input Level: -20dB mic, 40dB MonitorOutput Impedance: 10 ΩSignal To Noise Ratio: 90dBGain: 15dB (1/4 in), 50dB (XLR)Power: LED indicatorDimensions: 4.5x2.75x1.5 inches (112mm x 72mm x 40mm)Weight: 1.3lb (590g)Power Requirements: 12V DC (Adapter included) or one 9V battery
The HeadAmp4 offers 1/8th-inch as well as 1/4-inch inputs and outputs as well as lower noise, lower distortion and more output in a new custom extruded stackable metal case.Ideal for virtually any home or project studio, the ARTcessories HeadAmp4 easily adds additional headphone outputs to any mixer, computer audio interface, workstation, iPod, media player or laptop without creating any additional load on the existing headphone source.Individual level controls for the four headphone outs, 1/4-inch and now 1/8th-inch connections allow the HeadAmp4 to connect to virtually any source, and drive any headphone configuration including studio phones, in-ear monitors or custom ear pieces or any combination of the above.Features:4 Output Channels Each with Individual Volume ControlStereo ¼-inch & 1/8-inch Inputs (Wired Parallel)Can be Connected to Any Line-Level Source or Headphone OutputFour Stereo ¼-inch & Four 1/8-inch Headphone OutputsPower "On" LEDSpecifications:Maximum Input Level: +14dBVInput Impedance: 90.9k ΩMaximum Output Level: +14dBuMaximum Gain: 20dBOutput Impedance: 47 Ω (each output)Frequency Response: 20 - 20 kHzSignal To Noise Ratio: > 90dB (ref 0dBu)Total Harmonic Distortion:
Omnitronic LH-030 4-channel headphone amplifier.Features:Distributes the signal of 1 audio source to 4 sets of headphones4 channels with separate level controls and headphone outputsAll connections via 6.3 mm jacks (1/4")Operation via supplied power unitSpecifications:Power supply: 12 V DC, 150 mAInput impedance: 100 kohms unbal.Max. input level: +14 dBInput impedance: 100 kohmsOutput impedance: 51 ohmsGain: 20 dB/channelT.H.D.: 0.008 %Frequency range: 20-20000 HzS/N ratio: >90 dBDimensions: 113 x 73 x 40 mmWeight: 340 g
Perfect for studios, practice spaces, quiet stages, and more, the HM Series offers everything you need whether it is just splitting a single signal to your band, or more complex headphone distribution. Whether you need to expand your home studio headphone monitoring capability or add robust cue mix distribution, the affordable HM Series offers the sound quality, reliability, and flexibility you need to expand your setup. The two 19" rackmount models, the HM-400 and HM-800, deliver flexible, robust headphone distribution for studios, practice spaces and more.Features:XLR & 1/4" Stereo Inputs and OutputsThree Headphone Outputs per ChannelPer-Channel 1/4" Stereo Aux Input2-Band EQ, Balance, and Output Controls
Perfect for studios, practice spaces, quiet stages, and more, the HM Series offers everything you need whether it is just splitting a single signal to your band, or more complex headphone distribution. Whether you need to expand your home studio headphone monitoring capability or add robust cue mix distribution, the affordable HM Series offers the sound quality, reliability, and flexibility you need to expand your setup. The two 19" rackmount models, the HM-400 and HM-800, deliver flexible, robust headphone distribution for studios, practice spaces and more.Features:Distribute Signal to 16 HeadphonesTwo Stereo Main Inputs via 1/4" JacksTwo Stereo Main Outputs via 1/4" JacksTwo 1/4" Headphone Outputs per Channel
Whether you need to expand your home studio headphone monitoring capability or add robust cue mix distribution, the affordable HM Series offers the sound quality, reliability, and flexibility you need to expand your setup.The ultra-compact HM-4 offers a simple yet effective way to split a single stereo signal out into four pairs of headphones. Perfect for quickly splitting a phones mix in the studio or even crowding around a tablet to watch a movie at home.Features:Distribute a stereo input signal to up to four pairs of headphonesIdeal for musicians in home and studio recording sessionsOne unbalanced 1/4" TRS stereo inputFour unbalanced 1/4" TRS stereo headphone outputsDedicated per-output level control allows each person to set a different listening volumeFront-panel power status indicatorHeavy-gauge steel chassis for long-lasting durability in the studio or on the roadIncludes 12 VDC power supply
The new irDAC-II continues the story adding Bluetooth connectivity, headphone output and DSD128 support. The irDAC-II comes packed with cutting edge technology and features that will benefit the most demanding user. We have gained a lot of knowledge developing class leading DACs. Areas like isolation of the digital and analogue stages, ultralow noise power supplies and a direct coupled signal path make a big difference.Using the outstanding ESS Sabre DAC to obtain performance that we believe will be unmatched in this price category. Jitter reduction is an obsession within our engineering team. They have applied their experience in the irDAC-II to produce a signal that is almost jitter free. The headphone output stage has been taken from the flagship A49 amplifier and is capable of driving the most demanding of headphones. Both fixed and variable line outputs are also available, allowing for ultimate system building flexibility.The irDAC-II is designed to be the heart of a digital system and can be connected to a host of different types of digital sources and connections. This includes asynchronous USB and Bluetooth. All of the inputs can be controlled through an IR remote that will also give you transport control of a PC or Mac USB source via the HID (Human Interface Device) control.Specifications:Input: USB, SPDIF, optical, BluetoothFrequency Response: 20Hz:20kHz, +/:0.1dBTotal Harmonic Distortion + Noise: 0.0007%Signal-to-noise ratio (A:weighted): 117dB (24:bit)Maximum output level: 2.1V RMSUSB: 32kHz, 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz, 384kHzOptical: 44.1kHz, 48kHz, 88.2kHz, 96kHzCoaxial: 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHzBluetooth: SBC, AAC, aptX, aptX:LLBit Depth : 16:bit, 24:bitHeadphone : 30Ω : 600Ω, 3.5mm plugPower requirements: 18W maxDimensions: W194 x H44 x D124mmWeight: 1.1kg
The POWERPLAY P1 Personal In-Ear Monitor (IEM) Amplifier puts control where it’s most useful – right at the artist’s fingertips. Whether on stage or in the studio, the P1 provides performers and recording artists with a dependable and affordable personal monitoring solution.Features:In-ear monitor amplifier for personal monitor applicationsHigh power and "drummer proof" headphones outputDual XLR inputs allow for 2-channel mono or stereo operationSwitchable stereo/mono operation with mix functionLevel and Balance/Mix controlsRuns up to 12 hours on a 9 V battery (not included)Battery control with dual LED indicatorsOperates on BEHRINGER PSU-SB DC power supply (not included)Integrated current limit protects your ears and headphoneConvenient belt-pack clip includedMounts easily on a standard mic stand with 5/8” and 3/8” thread"Built-like-a-tank", impact-resistant metal chassisDesigned and engineered in Germany
Whether you’re a keyboardist, drummer, or any other musician whose performance keeps them anchored in one spot, the PM1 was designed specifically for you. A convenient hardwired personal in-ear control center, the PM1’s belt pack puts monitor control right at your fingertips, plus it’s lightweight, ultra-easy to use – and it doesn’t require a power source!Features:In-ear monitor belt-pack for personal monitor applicationsHigh quality volume controlXLR input with locking mechanism3.5 mm mini jack headphones connectorConvenient belt-pack clip included"Built-like-a-tank", impact-resistant metal chassiDesigned and engineered in Germany
All essential functions in a stylish, slim housing. The Phonitor e offers Phonitor Matrix, volume remote control, connection also for balanced headphones, DA converter option and the all superior VOLTAiR technology. For all headphones The Phonitor e offers connections for standard headphones with jack plug and for balanced headphones a 4-pin XLR connector. Thanks to the high output power, all headphones are driven effortlessly. Volume with remote control The volume is adjusted with a milled all-aluminium rotary knob. The Alps RK27 “Big Blue” potentiometer provides a pleasant “spoon in honey” turning feeling. The volume can be adjusted with any infrared remote control. The Phonitor e learns their commands. To do this, press the IR programming button on the back and then the buttons for louder and softer. Source selection A total of five sources can be connected to Phonitor e: XLR, Cinch, USB, Coax, and Optical Phonitor e is equipped with RCA connectors and balanced XLR connectors for the analog inputs. The optional DAC768xs adds three more digital sources: USB, Coax and Optical. The optional DAC768xs The converter chip used in the optional digital-to-analog converter is the highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip, which thanks to its new architecture reproduces the finest sound details. It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768kHz, which corresponds to 16 times the CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. The Revolution in the headphone amplifier is the Phonitor Matrix, with switchable crossfeed, thanks to which you can listen to music with headphones as if you are listening to speakers. The tiring super stereo effect and the exaggerated reproduction of reverberation rooms and effects are a thing of the past. Enjoy your music without tiring and exactly as it should be heard. The Phonitor Matrix, in its largest expansion stage, has three adjustment parameters: Crossfeed, Speaker Angle and Center Level. In Phonitor e the center level is preset to -1 dB and the speaker angle to 30°. These are the most common values. The crossfeed function determines the crosstalk of the channels, the so-called interaural level difference. There are two switch positions C1 and C2 for the intensity of the crossfeed. Specifications: Analog Inputs: XLR (balanced), RCA Maximum input gain: 32.5 dBu Input impedance: 20 kΩ Digital Inputs: DAC768xs (optional) Coaxial SPDIF (RCA), PCM sample rates: 44.1/48/88.2/96/176.4/192 kHz Optical SPDIF (Toslink F06), PCM sample rates: 44.1/48/88.2/96/with Glass fibre
The headphone amplifier with preamplifier Enjoy music over headphones and over speakers equally excellently with the superior VOLTAiR technology – that’s why we developed Phonitor x. For all headphones The Phonitor x offers connections for standard headphones with jack plug and for balanced headphones a 4-pin XLR connector. Thanks to the enormous output power of 18 watts, all headphones are driven effortlessly. To the power amplifiers or to the active loudspeakers you can use the balanced XLR- for long, and the RCA sockets for short cable runs. Practical are the AMP CTL sockets to which power amplifiers with 12V trigger inputs can be connected to switch them on and off together with Phonitor x. Milled from solid is the big 45mm Volume control. Its mass together with the motorized Alps RK27 “Big Blue” potentiometer enhances the “spoon in the honey” feeling even further. The red marker LED makes the setting visible even in darkened environments. Volume RC The volume can be remote controlled with any infrared remote control, that the Phonitor x simply learns. To do this, press the IR programming button and then the buttons for louder and quieter. Source of joy Up to six (6 !) stereo sources can be connected to Phonitor x: XLR, RCA, USB, Coax, Optical and AES/EBU Phonitor x accepts a large variety of audio connections. Balanced via XLR or unbalanced via RCA connectors. With the optional DAC768xs, three additional digital sources can be added. The DAC768xs The highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip is used as the converter chip in the optional digital-to-analogue converter, which thanks to its new architecture reproduces the finest sound details. It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768kHz, which is equivalent to 16 times CD resolution. Direct Stream Digital is also supported up to a resolution of DSD4 or DSD256. Good ol' times Two mechanical VU meters visualize the input levels for the left and right audio channel. Finding the middle is not always easy. By our very nature, hearing can be leaning more to the left or more to the right. This is especially obvious when listening with headphones. That’s why Phonitor x has the uniquely finely resolved laterality control. With it, the center can be found perfectly. With the mode switch you can choose between stereo or mono playback. To the right, the laterality control is switched on. The Revolution in the headphone amplifier is the Phonitor Matrix, thanks to which you can listen to music through headphones as if you were listening through speakers. The tiring super stereo effect is a thing of the past. Enjoy your music exactly the way it should be heard. Specifications: Analog inputs & outputs: XLR (balanced) and RCA Maximum input & output gain: 32.5 dBu Input impedance (RCA): 20 kΩ Input impedance (XLR): 20 kΩ Output impedance: 75 kΩ Common mode rejection (XLR): 82 dB Frequency range (-3dB): 4 Hz – 300 kHz THD + N (10 Hz – 22 kHz, 0 dBu): 0.00085 % Noise (A-weighted): -103.8 dBu Crosstalk (1 kHz): -106 dB Dynamic range: 136.3 dB Digital Inputs: DAC768xs (optional) Coaxial SPDIF (RCA), PCM sample rates: 44.1/48/88.2/96/176.4/192 kHz Optical SPDIF (Toslink F06), PCM sample rates: 44.1/48/88.2/96/with Glass fibre
Years of experience in making high quality headphone amps have been distilled into the design of the MX-HPA. As a result, this fully-balanced headphone amp offers an awe-inspiring listening experience.The MX-HPA’s technical performance is stunning. Typically, distortion from 20 Hz to 40 kHz is less than 0.005%. Signal-to-noise ratio is better than 120dB (‘A’ weighted). Frequency response is ruler flat from 10 Hz to 20 kHz (-0.1dB).The MX-HPA is capable of a short-term peak of 10 watts (for one cycle) and has two gain positions: 18dB (8X) and 24dB (15X). Inputs are either balanced or single-ended. The MX-HPA will automatically convert single-ended inputs to balanced. The MX-HPA is genuinely fully balanced from beginning to end.Specifications:OutputPower 1.8 Watts per channel into 8 Ohms (27dBW)Maximum output voltage 19 Volts RMS, 20Hz to 20 kHzOnset of clipping (54 Volts peak-to-peak) balancedLine inputTHD+N >0.005% typical, 20Hz to 20 kHzSignal / noise ratio >120dB ‘A’-weightedInput impedance 50k OhmsFrequency response +0, –0.1dB, 10Hz to 20 kHzGain, LO position (volume max) 18db (8x)Gain, HI position (volume max) 24dB (15x)ConnectionsLine level inputs1 pair line level XLR (balanced) connectors1 pairs line level RCA connectorsHeadphone outputs1 pair 3-pin XLR/¼” stereo Jack combined socketsPower requirementMains voltages 90-250VAC 50-60Hz universal worldwide supplyConsumption >0.25 Watts standby (Orange LED lit)15 Watts maximum (Blue LED lit, full power output)GeneralDimensions - WxHxD (mm): 220 (82/3”) x 53 (2”) x 240 mm (9½”)Weight (unpacked / packed): 2.2 kg (5 lbs) / 3.7 kg (8¼ lbs)