Radial

The Radial Trim-Two is a passive direct box, designed for use with laptop computers and other consumer devices where the user has a requirement for a 'ready access' volume control for quick adjustments on stage.The design begins with a choice of inputs including dual ?" jacks, left and right RCAs and a stereo 3.5mm input. These are wired in parallel to allow the signal to be split off to feed an alternate signal path such as monitors. Inside, two great sounding Eclipse transformers do the work of isolating and balancing the signal. These 'passive engines' deliver a linear frequency response from 20Hz to 18kHz and are capable of handling up to +15dB signal levels thus providing typical -10dB consumer-level devices with plenty of headroom. An easy access front panel stereo level control makes adjusting the volume a snap. A handy stereo-to-mono switch makes it easy to reduce the output channel count or send the same balanced signal to two destinations at once. Transformers provide galvanic isolation between the source and the destination and are extremely effective at eliminating hum and buzz caused by ground loops. This is augmented with a ground lift switch at the XLR outputs. One merely connects the source to the Trim-Two and then the male XLR outputs to the PA system. As the Trim-Two is completely passive, no power is required.Made in Canada from heavy duty 14 gauge steel, the Trim-Two features Radial's unique book-end design that creates protective zones around the connectors and controls. Inside, the unique I-beam frame protects the sensitive inner workings from potential damage that could torque the PC board and cause solder pointes to prematurely go cold. The steel casing also provides shielding against external magnetic fields.These features make the Trim-Two a great choice for keyboard players, DJs, audio-visual presenters and others that employ a laptop or tablet with a handy volume contro

The Radial Phazer™ is an analogue phase alignment tool that lets you bring two sound sources together so that the fundamentals play in sync. Once in phase, the results are impressive: On electric guitar; you can combine the direct feed of an amp with a room mic to create fat rich tones. On a kick drum, combine the 'attack' sound from a batter head mic with the 'boom' captured by the outer shell mic. On a snare drum, combine the top and bottom mics and on acoustic instruments, combine a close 'spot' mic with a room mic to capture textures like never before.The Phazer is designed from the ground up for optimum sound quality. It employs full-size 100% discreet class-A electronics to deliver the warmth and thickness that is simply not possible with chip based devices. This results in smooth, natural sounding phase curves which are particularly noticeable in the lower frequency spectrum. 0º to 180º phase adjustment is performed with a single knob making it easy to zone-in on the sweet spot. For the more adventurous, a 180° polarity reverse switch accesses the 181° to 360° range and lets you create weird to absurd 'Phazed' tonal textures. This is augmented with a variable low-pass filter that lets you focus the effect in the lower frequency spectrum - where phasing is most audible.Built Radial tough for the road, the Phazer is equipped with an innovative book-end design that creates a protective zone around the knobs and switches. Construction is 14-gauge steel with an internal I-beam frame that protects the sensitive electronics in even the harshest touring environments. A full bottom no-slip pad provides electrical insulation to eliminate electrical bonding and mechanical isolation to reduce mishap.The Radial Phazer is a creative tool for the studio designed to expand your tonal palette. Live, it delivers great sound fast. Once you try one, you will never mix without!Features:Time align two signals for exceptional clarity100% analogue, does not 'step' like digital delayLow-pass filter lets you focus the effectOnce you try it, you will never mix without

The Radial Tonebone Mix-Blender™ is a multi-function pedal that lets you mix two instruments or effects together and then send the combined signal through a mixer-style effects loop for processing. Designed to work with guitar, bass and keyboards, the Mix-Blender begins with two high-performance Class-A buffers for maximum fidelity.  These lower the impedance to drive the signal further without noise. Individual volume controls on each channel let you mix the two inputs to suit and can be used to blend two pickups on an acoustic guitar, combine two pedals in parallel such as a chorus and a distortion, or to have two different instruments 'live' on stage – each set with the same output for quick changeovers. The signal can then be routed to a true 'mixer-style' effects loop and activated using the on-board footswitch. This features a wet-dry blend control that lets you mix-in effects pedals with precise control to add slight enhancements or extreme coloration to the signal chain. In other words, the Mix-Blender lets you retain the original sound of the instrument and add in as much of the effect as you like.  Think of adding a touch of overdrive to a bass guitar without losing the bottom end. How about mixing in some distortion to your acoustic guitar to give it more shimmer? How about adding a chorus or phase shifter to your Hammond synth patch? The Mix-Blender is a unique tool that is designed to bring new tonal textures to your world and enhance your creative inner spark. Features:Mix two instruments or effects together at same timeBlend in effects while retaining the tone of your instrumentClass-A buffered inputs with individual level controlsOpens door to creating subtle or unique effects 

The Radial Bassbone is a power-packed bass preamp that combines on-stage efficiency, amazing tonal control and superb audio performance making it the ideal front end for both live and studio recording.Designed as a bass command center, the Bassbone lets you connect two basses and seamlessly toggle between them using a footswitch. Each channel is equipped with a separate level control to balance the two instruments. This is augmented with a unique EQ that enables you to adjust the tone for each instrument to match with your bass amp. In fact, the EQ is so powerful that you can toggle between channels to emulate switching from a P-Bass to a Rickey using the same bass! For added stage control, a second footswitch engages a power booster for soloing. This works double duty to turn on an effects loop.The Bassbone's highly acclaimed audio circuit features full sized discrete electronics for optimal signal flow to deliver the sound of your bass to your amp with minimal distortion or artefact. Outputs include a ¼" instrument output for the stage amp, separate always-on tuner out, and a built-in Radial direct box to feed the PA or recording system. The Bassbone ... finally a pedal that gives you control and great tone in one.Features:Two-channel bass preamp for 1 or 2 bassesBuilt-in Radial direct box with low-Z balanced outCombination power boost and effects loopPowerful EQ and contour control for each bass

The Plexitube™ is a two channel tube distortion that combines the natural warmth and harmonic generation of a 12AX7 tube with the control and saturation of our unique multi-stage solid-state drive circuit. Combine this amazing front-end with our unique passive-interactive tone controls and the Plexitube is able to deliver four generations of over-the-top Marshall tones from a single pedal.Designed to enhance on-stage functionality, the Plexitube features two distinct distortion channels for on-the-fly transitioning between rhythm and lead settings. Channel-1 has been optimized for rhythm with huge chunky rhythm tones and scooped out mids for a thunderous wall-of-sound and complete world domination. Channel-2 is optimized to produce razor-sharp cut for solos and sustaining mids that are so smooth, they can make a grown man cry. This is augmented with individual voicing and contour controls for each channel that let you dial in the optimal tone to suit your guitar and playing style.When the Plexitube is switched off, true-bypass connectivity ensures the natural tone of your guitar goes directly to your amp without obstruction or a tone robbing load. And when activated, photocell switching assures smooth pop-free actuation even when used with high gain amps. There's even an effects loop that can automatically turn your delay on when you switch channels for leads. No tap dancing required! The Radial Tonebone Plexitube takes metal guitar one step beyond anything you have experienced so far. God Save the Queen!Features:The best 'Marshall in a pedal' of all time!Delivers clean, rhythm and lead in one pedalTrue bypass clean for natural toneInsert loop on lead channel for effects

The Radial J33 is a combination phono preamplifier and purpose built stereo direct box made to handle the rigors of the professional recording studio and the abusive environment of live touring. But don't let the tough exterior fool you… the J33's sonic performance will easily surpass many audiophile preamps costing much more. The Radial J33, a high performance turntable preamp that is ideally suited for music playback, archiving, DJing and sampling.Designed specifically for dynamic cartridges, the J33 begins with a low noise front end. Inputs are standard RCA with the required turntable ground lug. A precise RIAA low pass filter is tailored to produce a smooth, warm response. The signal is then buffered to provide the audio system with a standard -10dB signal with choice of RCA connectors for compatibility with home HiFi entertainment systems, 3.5mm (1/8") output to feed a laptop or iPod, or a stereo TRS ¼" jack for an audio recorder. A second set of direct box XLR outputs deliver a mic level signal to feed a concert snake, mic splitter and mixing desk preamp inputs. A rumble filter is also available for high sound pressure environments to reduce bothersome resonant feedback.As with all Radial DIs, the J33 features a 14 gauge steel enclosure with a unique book-end design that creates a protective zone around the switches and connectors. The internal I-Beam construction ensures maximum rigidity while ensuring minimal stress on the sensitive solder joints. These combine to provide exceptional shielding against noise while ensuring greater dependability in the most demanding environments.Features:Combination RIAA Phono preamp and DI boxStereo RCA, ¼" TRS, 3.5mm and XLR outputsBuilt -in low frequency rumble filterChoice of 48V phantom or DC supply

The Radial USB-Pro is a high-resolution stereo direct box designed to convert sound files from a laptop computer and seamlessly transfer them to a pair of balanced audio outputs to feed a PA, recording or broadcast mixing console.Made to be plug & play easy to use, the USB-Pro automatically configures itself for use with all popular operating systems including Mac OSX, Windows XP, Vista and Windows 7, thus eliminating the need to load special drivers. Unlike devices that are limited with 16 bit, 44.1kHz conversion rates, the USB-Pro elevates the performance with true 24 bit, 96kHz stereo converters to deliver more headroom and greater detail. This eliminates the need for additional sound cards or separate converters when transferring files, further streamlining production in busy work environments.Connection from the laptop is done via the 'pro-audio standard ' USB type-B port. Digital-to-analog conversion is monitored with the built-in headphone amplifier to ensure the signal is being properly downloaded and converted. A mono-sum switch may be engaged to check for phasing or facilitate signal distribution to two outputs should this be preferred. One simply sets the output volume control to suit. Should hum or buzz caused by ground loops be encountered, two 'set & forget' side-access switches let you insert isolation transformers into the signal path to block stray DC voltage offsets. To further reduce susceptibility to noise, this is augmented with a ground lift switch that lifts pin-1 on the two XLRs.As with all Radial products, the USB-Pro is designed to handle the rigors of professional touring. Our unique book-end design creates protective zones around the switches, connectors and controls to keep them out of harm's way. Inside, our time-tested I-beam construction assures the sensitive internal PC board will not torque which could otherwise cause premature part failure. Finally, a full bottom no-slip pad provides mechanical isolation and electrical insulation, further advantaging the user.Features:High performance 24bit/96k stereo direct boxAutomatically installs without the need of a driverBuilt-in headphone amplifier for monitoringBalanced Lo-Z outputs with switchable isolation

The Radial PZ-DI is a unique direct box that is specifically designed for acoustic and orchestral instruments. Unlike most direct boxes that are limited to a 'one size fits all' design, the PZ-DI lets you properly match the input impedance to the source to optimize the frequency response, dynamics and feel so that no matter what type of pickup you employ, you will enjoy smoother, more musically pleasing results.The design begins with a 3-position load adjustment switch: The 1 meg-ohm position delivers the classic impedance found on most active DI boxes. The 220k-ohm setting warms up the tone of a magnetic pickup to give you the feel and tone as if connected to a tube amplifier. The ultra-high 10 meg-ohm impedance is used to compensate for the harsh, squawky tone that usually plagues piezo-equipped instruments. This is followed by a fully variable high-pass filter that lets you 'size the instrument' by gently rolling off bass frequencies to eliminate unwanted resonance. You could for instance, retain the low frequencies on a cello or increase the cut-off point to better suit a violin. For active instruments such as acoustic guitars that incorporate a battery powered preamp, you can engage a low-pass filter to gently soften the hard edge for a smoother more natural tone.To maximize signal handling and reduce distortion, the PZ-DI incorporates an innovative DC to DC switching supply that converts the phantom power to deliver extra headroom. This provides ample dynamic range for acoustic instruments. Should an extra loud source such as an active bass or digital keyboard be encountered, simply activate the -15dB pad to satisfy the situation. Other problem solvers include a 180° polarity reverse switch to tame hot spots on stage that can cause feedback and a ground lift switch to help eliminate hum and buzz caused by ground loops.The Radial PZ-DI is a ground breaking direct box that can instantly adapt to all types of pickups so that you can enjoy the full frequency response and dynamics of an orchestral string instrument, smooth-out the peaks of bluegrass fiddle, banjo or mandolin, split off a bass guitar without excessive loading, or naturally amplify an acoustic guitar without the usual tone-altering effects.Features:Optimized for orchestral instruments on a live stageAdjustable load for piezo and magnetic pickupsVariable low-cut filter to control bass resonance48V phantom powered, does not require batteries

The Radial Pro48's innovative digital switching power supply significantly increases headroom and allows for less distortion while yielding a smooth, linear response extending from 20Hz to well above 100kHz resulting in natural, uncolored signal transfer. This superior performance makes the Pro48 an ideal candidate for use with today's battery-powered active basses and acoustic guitars that tend to overload other direct boxes.Jack in/thruXLR out- 15 dB padGround/lift48V phantom powerThe compact Pro48 is built road-ready with 14-gauge steel in a unique bookend design that provides protective zones around the switches and connectors. The internal welded I-beam construction assures outside stress will not torque the PC board thus assuring longer product life. The Pro48 is designed for high-use applications wherever an active direct box is called for. A 15dB pad switch is provided to tame hot signal and expands the range of instrument preamps and the ground lift switch helps eliminate hum and buzz problems caused by ground loops.Features:High-resolution active direct boxIncreased dynamic range and headroom48V phantom-powered with digital switchingCompact, rugged book-end designIdeal for active guitars and bassesApplications:Active acoustic guitarActive bass guitarActive electric guitar with preampKeyboard / SynthesizerDirect recording

The Radial StageBug SB-2 Passive is a high-performance direct box made for players who are on the move! Made to fit inside of a guitar case, the SB-2 is ultra compact yet is feature-packed to ensure great performance on any stage. These features make the StageBug SB-2 a great choice for electric bass, acoustic guitar and keyboards where small size and big performance matters.The compact design begins with a ¼" input and thru-put to feed the on-stage amp. This connects to the custom made Eclipse ET-DB3 transformer which performs the impedance matching and balances the signal. When using extra high output instruments, a -15dB pad can be inserted into the signal path. This enables the SB-2 to be used with active basses and digital pianos that often tend to overload the input side of the interface. An innovative stereo-to-mono merge function provides a convenient way to connect stereo keyboards and computers without having to reset the source for mono operation, saving time and input channels on the PA. The SB-2 output features an XLR wired to the AES standard with pin-2 hot.Once connected, the SB-2 delivers a smooth warm sound reminiscent of older vintage gear. The Eclipse ET-DB3 transformer is magical in its ability to handle extreme signal levels with a natural compression that is pleasing to the ears. The transformer also helps eliminate hum and buzz caused by ground loops by isolating the input from the output. This is augmented with a ground lift switch that lifts pin-1 on the XLR for quiet, professional results.Features:Passive DI for bass, acoustic and keyboardUltra compact to fit in your guitar casePlug & play easy to use feature setTransformer isolation eliminates noise

To Radial StageBug SB-1 είναι ένα υψηλών επιδόσεων ενεργό D.I. box, φτιαγμένο για τους μουσικούς που είναι συνεχώς σε "κίνηση" ! active DI-Box ειδικά για ακουστικές  κιθάρες48 V Phantom, Jack in - Jack out -XLR outswitchable 15 dB Padswitchable 180° Phase reverseΦτιαγμένο για να χωράει μέσα σε μια θήκη κιθάρας, το SB - 1 είναι εξαιρετικά συμπαγές και ταυτόχρονα εξαιρετικής απόδοσης για κάθε stage. Αυτά τα χαρακτηριστικά καθιστούν το StageBug SB-1 εξαιρετική επιλογή γιαηλεκτρικό μπάσο, ακουστική κιθάρα και πλήκτρα όπου το μικρό μέγεθος και η υψηλή απόδοση μετράνε.Ο συμπαγής σχεδιασμός ξεκινά με μια ¼ " είσοδο και thru-put για να τροφοδοτήσει τον ενισχυτή στη σκηνή . Αυτό συνδέεται με τον custom made Eclipse ET-DΒ3 μετασχηματιστή που εκτελεί τo impedance matching και μετατρέπει το σήμα σε balanced. Όταν χρησιμοποιείτε όργανα με υψηλή εξόδο, το -15dB pad μπορεί να εισαχθεί στη διαδρομή του σήματος. Αυτό καθιστά το SB-1 κατάλληλο για χρήση σε ακουστικές κιθάρες & ηλεκτρικά μπάσα.Ένας καινοτόμος stereo-to-mono συγχωνευτής, προσφέρει ένα βολικό τρόπο για να συνδέσετε στερεοφωνικά πλήκτρα και υπολογιστές, εξοικονομώντας χρόνο και κανάλια στο PA. Η έξοδος του SB-1 διαθέτει ένα XLR καλωδιομένο στα πρότυπα του AES, με το pin-2 hot.Το SB-1 έχει απαλό ζεστό ήχο που θυμίζει παλαιότερες vintage υλοποιήσεις.Ο μετασχηματιστής Eclipse ET-DΒ3 είναι μαγικός στη δυνατότητά του να χειριστεί ακραία επίπεδα σήματος με φυσικό τρόπο συμπίεσης που είναι ευχάριστος στα αυτιά. Ο μετασχηματιστής βοηθά επίσης να εξαλείψει το βουητό και το buzz που προκαλείται από βρόχουςγείωσης απομονώνοντας την είσοδο από την έξοδο .Χαρακτηριστικά:Active direct box for acoustic guitarUltra compact to fit in your guitar casePlug & play easy to use feature set48V phantom powered, no batteries needed!

The Radial StageBug SB-4 is a compact active direct box that has been optimized for use with piezo transducers. This enables violin, dobro, mandolin, cello, upright bass and other instruments that are best amplified using a piezo to be connected without compromising the tone or frequency response.The design begins with a ¼" input for the instrument pickup. Unlike typical direct boxes that have a 1meg-ohm input impedance, the SB-4 features a very high 5meg-ohm impedance that smoothes out troublesome peaks that give piezos a bad name. The higher impedance also broadens the frequency response for a more natural and pleasing sound. The active circuit performs the high-to-low impedance conversion and balances the signal to enable long runs upwards to 100 meters without loss, delivering spectacular linearity and low distortion throughout the audio range.To help eliminate feedback on stage, the SB-4 is equipped with a high-pass filter and 180° polarity reverse switch. The high pass filter eliminates excessive bottom end which in turn reduces resonance that can cause the top of the instrument to vibrate. The 180° polarity reverse helps reduce acoustic hot spots on stage by changing the phase relationship between the PA system and room acoustics which can combine at certain frequencies to create peaks. Reversing the polarity eliminates the acoustic peak without resorting to severe equalization which only serves to compromise the natural tone of the instrument. Connections include an AUX out for a stage amplifier plus a standard XLR output to feed the PA. Power is derived from the console's 48V phantom, thus eliminating the need for batteries or external supply. One simply connects, turns on the phantom power and plays.Features:Active DI optimized for piezo transducersSmoothes out peaks, eliminates squawkHigh pass filter eliminates resonanceUltra compact to fit in your guitar case

The Radial JPC is an analogue stereo interface designed to help solve the buzz and hum problems commonly associated with connecting a computer to an audio system. This is accomplished by combining active buffers and transformer isolation to create an effective 'hybrid' circuit.Intended for professional field use, the JPC comes fully loaded with choice of ¼", RCA and 3.5mm input connectors that make it easy to interface with all types of unbalanced audio sources such as computers, iPods, and CD players. It is equipped with isolation transformers to eliminate hum and buzz caused by ground loops and to further reduce system noise; while AC blocking capacitors in the active circuit prevent pollution from the audio system from bleeding back into the computer. Outputs are XLR balanced mic level for easy interface to snake systems and PAs. Powering the JPC is accomplished via 48V phantom from a mixing console. This enables the JPC to be used in concert environments without requiring an external power supply.The JPC is a great sounding stereo direct box that is plug-and-play easy to use with practically any consumer electronic device. The noise eliminating advantages makes the JPC a must-have problem solver for any technician's audio kit. The Radial JPC... an effective tool designed to make interfacing gear easy.Features:Easy to use stereo interface for laptop computersActive signal path with transformer isolationEliminates hum and buzz common to PCsFull connector options set for easy interface

The Radial J48 has been designed from the ground up to deliver the most natural tone. As a direct box manufacturer, we do not believe it is our task to alter the sound of your prized '1962 Fender Jazz Bass', but retain and transfer the true character of the instrument to the mixing console without adding distortion or introducing artifact. This design philosophy has gained a tremendous following from many of the world's most demanding musicians.Using only 48V phantom power, the Radial J48 is an active direct box that produces an exceptionally linear response that extends from 20Hz up to well above 40kHz. Low distortion of all types is achieved via a unique digital switching power supply that raises the internal operating rail voltage for added headroom and improved signal handling. The results are truly amazing. The J48 delivers an ideal even-order harmonic cascade and a sonic performance that outperforms DIs costing several hundreds more.And like all Radial products, the J48 is both feature-rich for studio and made tough to handle the road. This includes a -15dB input pad to tame extra loud signals, 180º polarity reverse for feedback control on stage and a ground lift to help reduce hum & buzz caused by ground loops. Special features include a merge function that elegantly mixes left-right signals to mono without phase cancellation. To minimize resonant feedback with acoustic instruments, the J48 is also equipped with an 80Hz high-pass filter (low-cut). When engaged, this also increases headroom by eliminating unneeded bass frequencies.Radial's innovative book-end design protects switches and connectors from abuse while the internal I-beam construction eliminates stress on the PC board. This serves to reduce solder joints from going 'cold' and delivers trouble-free performance for years. A full-bottom no-slip pad provides mechanical and electrical isolation while providing plenty of 'stay-put' for rockin' stages!The Radial J48 is used by artists as diverse as acoustic guitarist Tommy Emmanuel; super-star engineer Joe Chiccarelli; and one of the most successful bands of all time Fleetwood Mac. The Radial J48… the world's finest 48V phantom powered active direct box.Features:Ultra low distortion of all typesExceptional headroom & dynamic rangeRetains instrument's natural soundPowered by 48V phantom

The Radial JDI is a passive direct box designed to handle extreme signal levels without distortion of any kind. Unlike an active DI that is limited by the buffering amplifier’s rail voltage, the JDI employs a Jensen audio transformer as the engine. Jensen transformers are legendary in their ability to gracefully handle transients while delivering a smooth, warm sounding Bessel curve, reminiscent of the finest vintage gear. Ruler flat from 10Hz to 40kHz and with virtually zero phase deviation, the JDI delivers the natural, pure sound of the instrument without artifact.The 100% passive circuitry inside the JDI is incredibly efficient. The transformer performs both high-to-low impedance conversion and signal balancing at the same time with minimal loading and does so without any power whatsoever. The transformer also introduces a magnetic bridge that passes signal while rejecting stray DC voltage. This makes the JDI particularly adept at eliminating hum and buzz caused by ground loops.Features include input and throughput ¼” connectors, -15dB input pad, ground lift, and 180º degree polarity reverse to help phase align the instrument with the PA. A secondary circuit is added for direct interfacing with high output devices such as guitar or bass amp loudspeakers plus a unique merge function allows stereo sources such as keyboards to be summed mono, saving valuable input channels.Built tough to handle the abuse of live touring, the JDI features a 14-gauge steel I-beam inner frame and a unique book-end outer shell. The innovative design eliminates stress on the PCB, reducing opportunity for solder joints to go ‘cold’ while the outer shell creates a protective zone around the switches and connectors. The steel casing resists noise-causing electromagnetic pollution and the transformer’s sensitive inner workings are further protected from magnetic fields with a mu-metal can. This ensures the signal transfer is quiet and free from hum.These combined features have made the Radial JDI the most popular passive direct box in professional touring and an excellent choice for instrument interface in the studio! The Radial JDI… the world's finest passive direct box.Features:Jensen Transformer equipped passive DIEliminates hum and buzz from ground loopsVirtually zero phase & harmonic distortionExceptional signal handling and noise rejection

The Radial ProDI is a passive direct box that combines exceptional audio performance with solid dependable construction, making it the ideal general duty direct box for stage and studio. The heart of the ProDI is a custom wound Radial transformer. It features an exceptionally high 140kΩ input impedance to reduce loading while enabling the ProDI to handle extreme signal levels at all frequencies without distortion. This is further improved upon with an internal mu-metal shield to protect against electromagnetic fields that can cause unshielded transformers to distort.This compact direct box begins with 14-gauge steel I-beam skeleton for added rigidity and Radial's unique book-end design that creates a protective zone around switches and connectors. Glass filled nylon connectors and high cycle switches combine with the mil-spec PCB and internal RF filtering to provide durability and noise-free performance. A full bottom no-slip pad provides both mechanical isolation and electrical insulation to further protect against the rigors of professional touring.The ProDI is ideally suited for instruments such as bass guitar, active acoustics, keyboards and just about anything else! When you consider all of the features and the affordable price tag, it is no wonder the Radial ProDI has become one of the most popular direct boxes ever made. The Radial ProDI… Spectacular performance at a price that anyone can afford!Features:Compact passive direct box for stage and studioAble to handle huge transients without distortionTransformer isolation eliminates noisy ground loopsPlug and play easy to use feature set - on stage or in the studio

The Radial ProD2 is a compact stereo direct box developed specifically to address the needs and challenges of interfacing a stereo keyboard to a professional audio system. This passive DI features two independent channels with separate inputs and thru-puts for the artist's stage amp and two fully isolated outputs for the PA system.At the heart of the design are two high performance Eclipse ET-DB2 transformers. These deliver 20Hz to 20kHz performance with less than 1.5dB deviation above 18kHz and are able to withstand tremendous signal levels without distortion. Unlike active circuits that overload when the signal exceeds the rail voltage, transformers saturate. This creates a pleasing effect that naturally rounds out the tone, acting like a subtle limiter which is particularly advantageous when interfacing the ProD2 with digital pianos, samplers and drum machines that can produce excessive dynamics. Transformers are particularly adept at eliminating hum and buzz caused by ground loops.As with all Radial products, the ProD2 is built tough to handle the rigors of professional touring. A 14-gauge steel ultra rigid i-beam skeleton frame eliminates opportunity from outside stress to flex the sensitive PC board and cause premature solder joint failure. The innovative book-end design creates a protective zone around the connectors and switches further increasing lifespan. And a full bottom no-slip pad adds mechanical isolation and electrical insulation to further reduce opportunity for noise. The Radial ProD2's warm sound, legendary build quality and compact design have made it the most popular stereo direct box made today.Features:Stereo direct box designed for keyboardsSmooth, warm sound rounds out digital edgeAble to handle huge transients without chokingMay be rack mounted for touring rigs

The Radial X-Amp is an active Reamper™ that allows the engineer to play a pre-recorded track back through guitar amplifiers and pedals. This opens the door to explore new musical sounds and spur on the creative process so that your recording stands out.Using the X-Amp is easy: start by recording a dry track using a high quality direct box like the Radial J48. Send the new track from your recorder via the X-Amp to your guitar amps, effect pedals or combinations thereof. Once the basic track has been recorded, replacing or adding tracks can be done well after the session player has gone home. This eliminates tiresome repetition and assures a fresh vibrant performance on the final recording. Furthermore, by driving two amps at the same time, new sounds and textures can be created while allowing you to make artistic decisions as the recording progresses.Following the critically acclaimed Radial JD7 Injector, the X-Amp employs a unique class-A circuit design that has been optimized for use with guitars. Features include balanced line level input with LED peak indicator and level control, class-A circuit topology for optimal reach and frequency response, a transformer isolated output to eliminate hum and buzz caused by ground loops, a 180º polarity reverse switch to bring both amps into phase, and a dual ground lift switch for noise-free operation.As with all Radial products, the X-Amp is built like a tank to provide years of trouble-free performance. An internal I-beam skeleton provides maximum protection against external stress which could cause solder points to fail. This is supplemented with an innovative bookend design that creates a protective zone around the switches, potentiometer and connectors. A full bottom no-slip pad performs double duty by keeping the X-Amp from sliding around when placed on a vibrating amplifier while also providing electrical and mechanical isolation. Reamping works equally well on bass, keyboards, drums and voice. Once you start Reamping, you will never record any other way. The Radial X-Amp… the active Reamp® for professional recording engineers.Features:Active Reamp® with two outputs100% discrete class-A signal pathTransformer isolated to eliminate noiseVariable 'set & forget' level control

The Radial ProAV2 is a passive direct box specifically developed with the audio-video integrator in mind. It has full two-channel stereo functionality. To eliminate the need for various adaptor, a "Swiss Army" array of connections are provided, including 1/4" for instruments, RCA and 1/8" connectors for consumer electronics and computers, and a +4dB XLR input for professional systems. Front panel connectors can also be used as thru-puts to allow multiple patch points.Custom wound transformers are employed, which are able to withstand exceptionally hot levels while maintaining linearity from 20Hz to 18.5kHz. The resulting smooth Bessel curve is warm and natural, making the ProAV2 Passive DI box particularly adept at handling digital sources that can sound harsh. Transformer isolation adds the benefit of eliminating ground loops that cause audio hum and buzz and video hum bars or snow.Features:Great-sounding, flexible passive DIHigh performance custom-wound transformerPro "Swiss Army knife" direct box for multi-mediaEasy to use passive ultra-quiet designEliminates ground loops causing hum and buzzHandle huge transients without distortionCompletely passive, no power neededXLR, 1/4", RCA and 3.5mm inputsBuilt-in stereo to mono merge function-15dB PAD for wide range of input levelsConverts hi-Z consumer to low-Z mic-levelConnect a stereo source to a mono channelUnbalanced audio from CDs, laptops, VCRsUltra-tough 14 gauge steel enclosureSpecifications:Frequency response: 20Hz to 20kHz +/- 2.5dBTotal harmonic distortion: 0.01% THD 20Hz to 20kHzInput: Unbal, high-ZOutputs: Balanced 600-ohm, mic-level, pin-2 hotInput pad: -15dBPower requirement: NoneSize: 3.25" x 5" x 1.875"Weight: 1.8 lbs.