Tonar

The magnetic charge, which is generated on the recording- and playback heads during recording and playback is removed by this electronic, demagnetising wand in an electronic manner. Then the sound will be clear. Demagnetising takes only 3 to 5 seconds for each head. As a very strong magnetic field is generated by this accessory, do not use it if you have a pace-maker and do not use in the close vicinity of friends or family with a pace-maker.

The Nostatic Arm is the modern version of the formerly well known “Dust Bug” by Cecil   Watts. The Nostatic arm incorporates a carbon fiber brush that removes the static electricity from the record during playback, and at the same time picks up the loose dust before the stylus reaches that part of the record. The Nostatic arm has an earth wire which is connected to the earth of the record player or the amplifier. The height can be easily adjusted to fit most record players. It also has a sliding weight in order to adjust the “dusting force” of the brush. Finally the base of the brush has sticky tape so if preferred it can be stuck to the surface of the record player for easy use.

A accessory allowing you to achieve a very accurate mount level measurement. The Bubble level is framed in a stable housing with a glass plate with a measurement grid. The Three contact points on the bubble level and the housing size ensure stable positioning and clear indication of any sloping to help get the best sound quality from your turntable.Proper levelling is critical to getting the best sound from your turntable, making this accurate bubble level an essential vinyl accessory.This allows you to make sure your turntable is level. Simply place it on top of the turntable and check in several places, adjusting the turntable legs (if possible) or turntable platform or rack/shelf until your turntable is perfectly level. As proper levelling is critical to getting the best sound from your turntable, this is an essential vinyl accessory. A turntable on a slope is not good, it can effect the performance of your tonearm making it prone to jumping and skipping.This simple but effective level will tell you if your turntables are mounted on a flat surface for optimal.

This state-of-the-art DJ turntable brush combines the properties of the Tonar Classic brush and the Nostatic brush in one! The central part of the brush is made of ultra-fine high-quality velvet. This plush is flanked on both sides by a thick layer of very fine carbon fiber. Carbon fibers remove static from the disc so that dust loosens and can be easily collected by the plush in the middle of the brush even from the deep grooves of the discs.

High quality matte natural cork & rubber turntable to better insulate your vinyl records and minimize vibrations and transfer of static electricity.

In some cases, the original rubber mat on the turntable is very dirty or even chemically decomposed. Tonar now offers a fresh, freshly made rubber turntable mat to replace the old one.

High quality matte black leather turntable to better insulate your vinyl records and minimize vibrations and static electricity transfer.

High quality matte plexiglass turntable to better insulate your vinyl records and minimize vibration and static electricity transfer.

High quality 100% natural cork to better insulate your vinyl records and minimize vibration and static electricity transfer.

Brass Vinyl Record Stabilizer. Felt-coated base to avoid scratching the surface of your discs.

The new Tonar headgear, which has the SME style locking collar (as found on most Tonars). It is made from perforated aluminum which means it is strong and light. It weighs just 6.8 g, including the included cartridge cables and finger lift. It's also a pleasure to use thanks to the large finger lift shape.

The new Tonar headgear, which has the SME style locking collar (as found on most Tonars). It is made from perforated aluminum which means it is strong and light. It weighs just 6.8 g, including the included cartridge cables and finger lift. It's also a pleasure to use thanks to the large finger lift shape.

Replacement headrest (shell). Designed for use with a wide range of high-end and mid-range heads. Azimuth can be adjusted by loosening the screw located on the side of the platform body using a hex key. The housing uses high-quality, color-coded OFC pure copper wires with 24K gold-plated contacts that resist oxidation and provide stable signal transmission with minimal loss.

Replacement headrest (shell). Designed for use with a wide range of high-end and mid-range heads. Azimuth can be adjusted by loosening the screw located on the side of the platform body using a hex key. The housing uses high-quality, color-coded OFC pure copper wires with 24K gold-plated contacts that resist oxidation and provide stable signal transmission with minimal loss.

Brass vinyl record stabilizer.

Tonar Headshell made of cherry wood, which has the SME type locking collar (as found on most tonearms with removable headshells). The connectors are gold plated and the supplied header leads are silver plated.

This brush has high-quality velvet fabric to reach and clean deep into the grooves of the vinyl.

Brush with more than one million carbon fibers.

Equipped with premium quality OFC Copper Litz connection cables. Azimuth is adjusted by loosening the screw on the side of the shell. Comes with a loose lifting arm.

Equipped with premium quality OFC Copper Litz connection cables. Azimuth is adjusted by loosening the screw on the side of the shell. Comes with a loose lifting arm.

This record cleaning fluid intended for use in all types of record cleaning machines currently on the market is only suitable for vinyl records (Important do not use with old 78 RPM shellac records as the fluid may cause irreparable damage).

50 pieces of protective covers for 7" discs.

Covers for LP records, 10 inch, set: 25 pcs.

Covers for 10-inch discs, set: 50 pcs.

Protective anti-static 12" vinyl LP covers (pack of 25) made of anti-static plastic paper reinforcement inside.

Disc brush from Tonar with goat hair.The wet goat brush works best when used with disc cleaner and is a very effective brush for cleaning discs (especially old - worn ones) - after the disc washer.

You can't get away from having a perfectly clean needle all the time, tiny deposits on the playing surface of your vinyl will be dragged and deposited into your head needle, affecting sound reproduction and the life of your head. Simply move the tip of this brush gently under your head from back to front to clean your needle.

Having a sticky silicone surface that deforms when rolled over a disc surface, it can fit into the grooves and the dust and dirt inside will stick to the sticky cleaner. After use, the roller cleaner can be cleaned under a tap with water and a little soap, after drying it will stick like new.

Shell for all head types (except P-Mount). 9 g aluminum with its cables. Along with 2 weights of 2 g and 4 g for you to put on a low weight head so you can "weight" the arm with the head.

Inner sleeves suitable only for single discs (7 inches" - 17.5 cm). 50 pieces per package. antistatic inner sleeves (inner sleeves).

Precision arm-head scale. Complete with calibration weight, battery and case. Measuring range: 0.1 - 5 gr, accuracy: 0.01 gr.

The newly developed TONAR TOP TIP needle cleaning liquid with lubricant additive is very easy and simple to use. It is a powerful cleaning solution that will remove all the dirt your needle collects from the disc during playback and will result in a perfectly cleaned needle surface. The kit contains a bottle of TOP TIP cleaning and lubricating fluid as well as the TONAR Clean Tip carbon fiber needle cleaning brush.

A component that allows you to achieve a very accurate measurement of the support level. The Bubble level is framed in a fixed housing with a glass plate with a measuring grid. The three points of contact at the level of the bubble and the size of the housing ensure a stable position and a clear indication of any tilt to help you get the best sound quality from your turntable.

This head alignment "protractor" allows for the correct adjustment of the head you place on your turntable arm You will now only be able to enjoy the best possible sound from the head when it is properly aligned. Simply place this alignment gauge over the shaft of your turntable, move the head over the grid, and make sure it's properly aligned before tightening it onto your tonearm. It couldn't be simpler. The Tonar Simple Cartridge Protractor is an easy-to-use alignment tool for head adjustment. The Mirror Cartridge Alignment Protractor allows you to see and properly align your head needle for optimal groove tracking and music retrieval. This is one of the most important tools for turntable owners because the head's ability to retrieve music depends on its proper alignment with the record grooves. Maximize your listening pleasure with this simple and easy-to-use turntable head protractor. Finally, there is a mirror to check the azimuth of the head Suitable for all types of arms. Made in hard plastic, about the same thickness as an LP, with full instructions. This is a complete head alignment protractor available today and a must have tool for accurate head alignment.

Tonar Carbon Fiber Needle Cleaner. Dimensions: 9 x 9 x 2 cmWeight: 9.07 gr

This state-of-the-art DJ turntable brush combines the properties of the Tonar Classic brush and the Nostatic brush in one brush! The central part of the brush is made of ultra-fine high-quality velvet. This plush is flanked on both sides by a thick layer of very fine carbon fiber. Carbon fibers remove static from the disc so that dust loosens and can be easily collected by the plush in the middle of the brush even from the deep grooves of the discs.

Tonar plastipap liners (25 pieces) are made of super antistatic plastic paper reinforcement inside the plastic. This combination gives you dust-free anti-static protection for your precious discs, as well as added strength to prevent cases from folding and creasing when you slide the case out or through the disc cover. This model 5311 plastipap is only suitable for LP records (12 inch-30 cm). (Tonar plastipap covers are also available for 45 and 78 RPM records). (Tonar provides record covers for 33, 45 and 78 RPM records as well as outer sheets to protect your precious albums).

Tonar Woodgoat is a high quality goat hair brush for cleaning your records. This brush is made of pure goat hair and is used to clean discs using liquid. The shape of the bristles is such that they are ideal for applying cleaning fluids and getting into the grooves of the disc and cleaning them thoroughly. The wet goat brush works best when wet and is an effective disc cleaning brush.

Tonar plastipap antistatic record inner sleeves (25 pieces) are made of super antistatic plastic paper reinforcement inside the plastic. This combination gives you both a dust free anti-static protection for your valuable records as well as additional strenght to avoid folding and creasing of the sleeves when sliding the sleeve in and out of the record album. This model 5311 plastipap is suitable for LP records only (12 inch-30 cm). Tonar plastipap inner sleeves are also available for 45, and 78 RPM records.