Subwoofer

The launch of the DALI SUB E-9 F marks a new stage of what is possible at this level of subwoofers!The SUB E-9 features a 9” woofer, capable of moving lots of air with power and precision. The cone is made from pure aluminium for maximum stiffness and a becoming exterior. Furthermore, the heavy magnet system wields a massive 4-layer, long-stroke voice coil. All in all, the heavy-duty abilities of this “motor system” ensure that the woofer always follows the signal from the amplifier!The heart of this subwoofer is the 170W RMS Class D amplifier with a highly linear response. Embracing a classic DALI trademark, it simply acts as a total low frequency extension of your AV system.The result is a powerful, wellbalanced bass reproduction and flawless integration with your speakers. In addition, the integrated limiter helps protecting your subwoofer against overloading.The back plate of SUB E-9 F features controls for volume adjustment, phase, and upper cut-off frequency, while the power on/off function works automatically via signal detection. And with the options for LFE or LINE inputs, this subwoofer easily accompanies any AV set up.SUB E-9 F is elevated from the floor by cone shaped rubber feet, while a down-firing bass port allows positioning directly against the wall. The DALI SUB E-9 F is recommended as compliment to the KUBIK FREE as well as the compact models of the ZENSOR and FAZON series. On top of this it is compatible with all DALI loudspeakers as the perfect completion of a DALI stereo or surround set up. HIGH-YIELD AMPLIFIERAll the amplifiers in the DALI subwoofers have the stamina to keep a high-yield performance and the headroom to draw out that little extra when needed.ALUMINIUM BASEGiving the illusion that the subwoofer is floating on air, the elegant aluminium base decouples the subwoofer from the floor and integrate seamlessly to the room.FLEXIBLE CONNECTIVITYAll DALI subwoofers are compatible with almost any amplifier, receiver or processor due to the choice of LFE or LINE inputs.ELEGANT AND SIMPLE DESIGNThe cabinet is designed to fit perfectly to the size of the woofer, but without forgoing the inner volume that is needed to produce a powerful bass performance. Specifications :Frequency Range (+/-3 dB) [Hz]37 - 200Maximum SPL [dB]111Crossover Frequency [Hz]40 - 120Low frequency driver, Quantity1 x 9" long strokeLow frequency driver, Diaphragm typeAluminium Enclosure typeBass Reflex Bass Reflex Tuning Frequency [Hz]39.0Max. Amplifier Power Output [RMS watt]220Continous IEC Power Output [RMS watt]170Input Impedance [ohms]25kConnection InputMono (LFE) RCA Stereo (low-pass filtered) Magnetic ShieldingNoRecommended PlacementFloor Recommended Distance From Wall [cm]    10 - 30FunctionsCrossover Frequency Phase Switch Standby (Auto Power) On/Off Switch Volume (Gain) Max. Power Consumption [W]250Dimensions With Base (HxWxD) [mm]  307 x 288 x 311Weight [kg]11.0Accessories IncludedManual 

The launch of the DALI SUB E-9 F marks a new stage of what is possible at this level of subwoofers!The SUB E-9 features a 9” woofer, capable of moving lots of air with power and precision. The cone is made from pure aluminium for maximum stiffness and a becoming exterior. Furthermore, the heavy magnet system wields a massive 4-layer, long-stroke voice coil. All in all, the heavy-duty abilities of this “motor system” ensure that the woofer always follows the signal from the amplifier!The heart of this subwoofer is the 170W RMS Class D amplifier with a highly linear response. Embracing a classic DALI trademark, it simply acts as a total low frequency extension of your AV system.The result is a powerful, wellbalanced bass reproduction and flawless integration with your speakers. In addition, the integrated limiter helps protecting your subwoofer against overloading.The back plate of SUB E-9 F features controls for volume adjustment, phase, and upper cut-off frequency, while the power on/off function works automatically via signal detection. And with the options for LFE or LINE inputs, this subwoofer easily accompanies any AV set up.SUB E-9 F is elevated from the floor by cone shaped rubber feet, while a down-firing bass port allows positioning directly against the wall. The DALI SUB E-9 F is recommended as compliment to the KUBIK FREE as well as the compact models of the ZENSOR and FAZON series. On top of this it is compatible with all DALI loudspeakers as the perfect completion of a DALI stereo or surround set up. HIGH-YIELD AMPLIFIERAll the amplifiers in the DALI subwoofers have the stamina to keep a high-yield performance and the headroom to draw out that little extra when needed.ALUMINIUM BASEGiving the illusion that the subwoofer is floating on air, the elegant aluminium base decouples the subwoofer from the floor and integrate seamlessly to the room.FLEXIBLE CONNECTIVITYAll DALI subwoofers are compatible with almost any amplifier, receiver or processor due to the choice of LFE or LINE inputs.ELEGANT AND SIMPLE DESIGNThe cabinet is designed to fit perfectly to the size of the woofer, but without forgoing the inner volume that is needed to produce a powerful bass performance. Specifications :Frequency Range (+/-3 dB) [Hz]37 - 200Maximum SPL [dB]111Crossover Frequency [Hz]40 - 120Low frequency driver, Quantity1 x 9" long strokeLow frequency driver, Diaphragm typeAluminium Enclosure typeBass Reflex Bass Reflex Tuning Frequency [Hz]39.0Max. Amplifier Power Output [RMS watt]220Continous IEC Power Output [RMS watt]170Input Impedance [ohms]25kConnection InputMono (LFE) RCA Stereo (low-pass filtered) Magnetic ShieldingNoRecommended PlacementFloor Recommended Distance From Wall [cm]    10 - 30FunctionsCrossover Frequency Phase Switch Standby (Auto Power) On/Off Switch Volume (Gain) Max. Power Consumption [W]250Dimensions With Base (HxWxD) [mm]  307 x 288 x 311Weight [kg]11.0Accessories IncludedManual 

Whether the task is to fill the room with stereo music or to feel the subtle tremor from a movie soundtrack the new DALI SUB K-14 F will deliver!Build around a 14” aluminium long stroke woofer and with a 500 watts class D amplifier the DALI SUB K-14 F has the power and the control for both impressive movie- and delightful music reproduction.Connect the sub to your amplifier through LFE or line-out, and prepare to be pushed down in your seat.Find other DALI Subwoofers or take a look at our loudspeaker series. Features of the SUB K-14 F14” aluminium long stroke woofer500 watts class D amplifierSolid aluminium baseWhite or black cabinetHigh gloss white or black front baffleCombination of use:DALI recommends applying this subwoofer with for example RUBICON, OPTICON and ZENSOR systems. However, customer with speakers from other brands will surely find what they need in this sub. RIGID CONE STRUCTUREThe rigid cone structure based on either aluminium or cone fiber eliminates the need for a dust-cap and helps ensure a piston-like behaviour of the woofer.HIGH-YIELD AMPLIFIERAll the amplifiers in the DALI subwoofers have the stamina to keep a high-yield performance and the headroom to draw out that little extra when needed.FLEXIBLE CONNECTIVITYAll DALI subwoofers are compatible with almost any amplifier, receiver or processor due to the choice of LFE or LINE inputs.ELEGANT AND SIMPLE DESIGNThe cabinet is designed to fit perfectly to the size of the woofer, but without forgoing the inner volume that is needed to produce a powerful bass performance. Specifications :Frequency Range (+/-3 dB) [Hz]29 - 160Maximum SPL [dB]115Crossover Frequency [Hz]40 - 120Low frequency driver, Quantity1 x 14" long strokeLow frequency driver, Diaphragm typeAluminium Enclosure typeBass Reflex Bass Reflex Tuning Frequency [Hz]34Max. Amplifier Power Output [RMS watt]    500Continous IEC Power Output [RMS watt]450Input Impedance [ohms]10kConnection InputMono (LFE) RCA Stereo (low-pass filtered) Magnetic ShieldingNoRecommended PlacementFloor FunctionsCrossover Frequency Phase Switch Standby (Auto Power) On/Off Switch Volume (Gain) Max. Power Consumption [W]650Dimensions With Base (HxWxD) [mm]429 x 396 x 428Weight [kg]26.4Accessories IncludedManual Spikes M8 

The launch of the DALI SUB E-12 F marks a new stage of what is possible at this level of subwoofers.The SUB E-12 features a 12” woofer, capable of moving plenty of air with power and precision. The cone is made from pure aluminium for maximum stiffness and a becoming exterior.Furthermore, the heavy magnet system wields a massive 4-layer, long-stroke voice coil. All in all, the heavy-duty abilities of this “motor system” ensure that the woofer always follows the signal from the amplifier!The heart of this subwoofer is the 170W RMS Class D amplifier with a highly linear response. Embracing a classic DALI trademark, it simply acts as a total low frequency extension of your AV system.The result is a powerful, well-balanced bass reproduction and flawless integration with your speakers. In addition, the integrated limiter helps protecting your subwoofer against overloading.The back plate of SUB E-12 F features controls for volume adjustment, phase, and upper cut-off frequency, while the power on/off function works automatically via signal detection. And with the options for LFE or LINE inputs, this subwoofer easily accompanies any AV set up.The DALI SUB E-12 F is recommended as compliment to the OPTICON, ZENSOR and SPEKTOR series and is compatible with all DALI loudspeakers as the perfect completion of a DALI surround set up. ALUMINIUM BASEGiving the illusion that the subwoofer is floating on air, the elegant aluminium base decouples the subwoofer from the floor and integrate seamlessly to the room.ELEGANT AND SIMPLE DESIGNThe cabinet is designed to fit perfectly to the size of the woofer, but without forgoing the inner volume that is needed to produce a powerful bass performance.HIGH-YIELD AMPLIFIERAll the amplifiers in the DALI subwoofers have the stamina to keep a high-yield performance and the headroom to draw out that little extra when needed.FLEXIBLE CONNECTIVITYAll DALI subwoofers are compatible with almost any amplifier, receiver or processor due to the choice of LFE or LINE inputs. Specifications :Frequency Range (+/-3 dB) [Hz]28 - 190Maximum SPL [dB]112Crossover Frequency [Hz]40 - 120Low frequency driver, Quantity1 x 12" long strokeLow frequency driver, Diaphragm typePolymere Aluminimum Enclosure typeBass Reflex Bass Reflex Tuning Frequency [Hz]36.0Max. Amplifier Power Output [RMS watt]220Continous IEC Power Output [RMS watt]170Input Impedance [ohms]25kConnection InputMono Line Level (LFE) RCA Stereo Line Level (low pass filtered) Magnetic ShieldingNoRecommended PlacementFloor Recommended Distance From Wall [cm]    > 5FunctionsCrossover Frequency Phase Switch Standby (Auto Power) On/Off Switch Volume (Gain) Max. Power Consumption [W]250Dimensions With Base (HxWxD) [mm]370 x 340 x 380Weight [kg]14.7Accessories IncludedManual Rubber Bumpers Spikes M6 

The launch of the DALI SUB E-12 F marks a new stage of what is possible at this level of subwoofers.The SUB E-12 features a 12” woofer, capable of moving plenty of air with power and precision. The cone is made from pure aluminium for maximum stiffness and a becoming exterior.Furthermore, the heavy magnet system wields a massive 4-layer, long-stroke voice coil. All in all, the heavy-duty abilities of this “motor system” ensure that the woofer always follows the signal from the amplifier!The heart of this subwoofer is the 170W RMS Class D amplifier with a highly linear response. Embracing a classic DALI trademark, it simply acts as a total low frequency extension of your AV system.The result is a powerful, well-balanced bass reproduction and flawless integration with your speakers. In addition, the integrated limiter helps protecting your subwoofer against overloading.The back plate of SUB E-12 F features controls for volume adjustment, phase, and upper cut-off frequency, while the power on/off function works automatically via signal detection. And with the options for LFE or LINE inputs, this subwoofer easily accompanies any AV set up.The DALI SUB E-12 F is recommended as compliment to the OPTICON, ZENSOR and SPEKTOR series and is compatible with all DALI loudspeakers as the perfect completion of a DALI surround set up. ALUMINIUM BASEGiving the illusion that the subwoofer is floating on air, the elegant aluminium base decouples the subwoofer from the floor and integrate seamlessly to the room.ELEGANT AND SIMPLE DESIGNThe cabinet is designed to fit perfectly to the size of the woofer, but without forgoing the inner volume that is needed to produce a powerful bass performance.HIGH-YIELD AMPLIFIERAll the amplifiers in the DALI subwoofers have the stamina to keep a high-yield performance and the headroom to draw out that little extra when needed.FLEXIBLE CONNECTIVITYAll DALI subwoofers are compatible with almost any amplifier, receiver or processor due to the choice of LFE or LINE inputs. Specifications :Frequency Range (+/-3 dB) [Hz]28 - 190Maximum SPL [dB]112Crossover Frequency [Hz]40 - 120Low frequency driver, Quantity1 x 12" long strokeLow frequency driver, Diaphragm typePolymere Aluminimum Enclosure typeBass Reflex Bass Reflex Tuning Frequency [Hz]36.0Max. Amplifier Power Output [RMS watt]220Continous IEC Power Output [RMS watt]170Input Impedance [ohms]25kConnection InputMono Line Level (LFE) RCA Stereo Line Level (low pass filtered) Magnetic ShieldingNoRecommended PlacementFloor Recommended Distance From Wall [cm]    > 5FunctionsCrossover Frequency Phase Switch Standby (Auto Power) On/Off Switch Volume (Gain) Max. Power Consumption [W]250Dimensions With Base (HxWxD) [mm]370 x 340 x 380Weight [kg]14.7Accessories IncludedManual Rubber Bumpers Spikes M6 

The DALI SUB P-10 DSS is designed with the goal to set standards for subwooferperformance and experience in your listening room or dedicated home theater. Unlike many subwoofers in the market the DALI SUB P-10 DSS has been engineered to perform equally well with both music and movies. It is important to us that a subwoofer is capable of rendering a performance true to the input signal.Therefore a DALI subwoofer is everything but a ‘boombox’.3 x 10 inch long stroke design woofers featuring rigid carbon fiber cones, dual spider, low loss suspension, and massive magnet system are fitted into an elegantly styled,Compact enclosure and combined with a powerful digital amplifier with a dynamic output of 500W RMS. DALI SUB P-10 DSS features a solid, down-firing woofer, able to move lots of air.The P-10 DSS remote controlled subwoofer, with individual settings and memory for stereo and theater, will be the competent upgrade to high-end stereo and home theater systems.Combination of use DALI recommends applying the subwoofer with e.g. EPICON, RUBICON and FAZON F5systems. APPLICATION But also customers with speakers from other brands will surely find what they need in this subwoofer. The design, technology, and construction of this subwoofer make it a perfect upgrade of any mid to high end loudspeaker system.More details are available in the Whitepaper. ELEGANT AND SIMPLE DESIGNThe cabinet is designed to fit perfectly to the size of the woofer, but without forgoing the inner volume that is needed to produce a powerful bass performance.FLEXIBLE CONNECTIVITYAll DALI subwoofers are compatible with almost any amplifier, receiver or processor due to the choice of LFE or LINE inputs.HIGH-YIELD AMPLIFIERAll the amplifiers in the DALI subwoofers have the stamina to keep a high-yield performance and the headroom to draw out that little extra when needed.RIGID CONE STRUCTUREThe rigid cone structure based on either aluminium or cone fiber eliminates the need for a dust-cap and helps ensure a piston-like behaviour of the woofer. Specifications :Frequency Range (+/-3 dB) [Hz]24 - 250Maximum SPL [dB]112Crossover Frequency [Hz]40 - 120Low frequency driver, Quantity1 x 10" long strokeLow frequency driver, Diaphragm typeCarbon fibre cone Low frequency passive driver, Quantity2 x 10" long strokeLow frequency passive driver, Diaphragm type    Carbon fibre cone Enclosure typeClosed Box With Dual Passive Radiators Max. Amplifier Power Output [RMS watt]500Continous IEC Power Output [RMS watt]300Input Impedance [ohms]26kConnection InputMono (LFE) RCA Stereo (low-pass filtered) Magnetic ShieldingNoRecommended PlacementFloor Recommended Distance From Wall [cm]> 5FunctionsCinema/Hifi Switch Crossover Frequency Standby (Auto Power) On/Off Switch Standby (Auto Power) On/Off Variable Phase Control Volume (Gain) Max. Power Consumption [W]550Dimensions With Base (HxWxD) [mm]370 x 340 x 340Weight [kg]19.5Accessories IncludedManual Remote Control Spikes M10 

The DALI SUB P-10 DSS is designed with the goal to set standards for subwooferperformance and experience in your listening room or dedicated home theater. Unlike many subwoofers in the market the DALI SUB P-10 DSS has been engineered to perform equally well with both music and movies. It is important to us that a subwoofer is capable of rendering a performance true to the input signal.Therefore a DALI subwoofer is everything but a ‘boombox’.3 x 10 inch long stroke design woofers featuring rigid carbon fiber cones, dual spider, low loss suspension, and massive magnet system are fitted into an elegantly styled,Compact enclosure and combined with a powerful digital amplifier with a dynamic output of 500W RMS. DALI SUB P-10 DSS features a solid, down-firing woofer, able to move lots of air.The P-10 DSS remote controlled subwoofer, with individual settings and memory for stereo and theater, will be the competent upgrade to high-end stereo and home theater systems.Combination of use DALI recommends applying the subwoofer with e.g. EPICON, RUBICON and FAZON F5systems. APPLICATION But also customers with speakers from other brands will surely find what they need in this subwoofer. The design, technology, and construction of this subwoofer make it a perfect upgrade of any mid to high end loudspeaker system.More details are available in the Whitepaper. ELEGANT AND SIMPLE DESIGNThe cabinet is designed to fit perfectly to the size of the woofer, but without forgoing the inner volume that is needed to produce a powerful bass performance.FLEXIBLE CONNECTIVITYAll DALI subwoofers are compatible with almost any amplifier, receiver or processor due to the choice of LFE or LINE inputs.HIGH-YIELD AMPLIFIERAll the amplifiers in the DALI subwoofers have the stamina to keep a high-yield performance and the headroom to draw out that little extra when needed.RIGID CONE STRUCTUREThe rigid cone structure based on either aluminium or cone fiber eliminates the need for a dust-cap and helps ensure a piston-like behaviour of the woofer. Specifications :Frequency Range (+/-3 dB) [Hz]24 - 250Maximum SPL [dB]112Crossover Frequency [Hz]40 - 120Low frequency driver, Quantity1 x 10" long strokeLow frequency driver, Diaphragm typeCarbon fibre cone Low frequency passive driver, Quantity2 x 10" long strokeLow frequency passive driver, Diaphragm type    Carbon fibre cone Enclosure typeClosed Box With Dual Passive Radiators Max. Amplifier Power Output [RMS watt]500Continous IEC Power Output [RMS watt]300Input Impedance [ohms]26kConnection InputMono (LFE) RCA Stereo (low-pass filtered) Magnetic ShieldingNoRecommended PlacementFloor Recommended Distance From Wall [cm]> 5FunctionsCinema/Hifi Switch Crossover Frequency Standby (Auto Power) On/Off Switch Standby (Auto Power) On/Off Variable Phase Control Volume (Gain) Max. Power Consumption [W]550Dimensions With Base (HxWxD) [mm]370 x 340 x 340Weight [kg]19.5Accessories IncludedManual Remote Control Spikes M10 

The wireless Wi-Q embodies three decades of leadership in bass technology. No other subwoofer in this price range gives you so much for so little.The Wi-Q is affordable, powerful, feature-rich and can be quickly and easily integrated into any entertainment system without the use of messy cables. A simple push of “EQ” on the remote and the exclusive, built-in processor produces optimal bass in your room from any source.Features:Wireless via Velodyne’s WiConnect System0.5 W Stand-By ComplianceCommon amplifier platformMaximum output and impactSuperior digital performanceExtended excursion driversEfficient green digital amplifiersDigital distortion limiting systemFour one-touch listening presetsOne-touch Auto-EQ room bass correctionInstantaneous front-panel feedbackFront-firing driver with down-firing ported cabinetFlexible low-pass crossoverRemote control Specifications:Amplifier: 450 watts Dynamic/225 watts RMS PowerAuto On/Off :YesCabinet Design: Extended Excursion Down-firing portColor: Black Ash VinylDimensions: (H/W/D) 18.44" x 16.375" x 18" (includes feet and grille) (46.8 x 41.6 x 45. cm)Frequency Response: (+/-3 dB) Overall 14.6 - 240 Hz (+/-3 dB) 25 - 120 HzHiPass Crossover: 80 Hz, 6 dB/octaveLoPass Crossover: 40 - 135 Hz adjustable (12 dB octave, 24 dB ultimate)Phase Control: 0, 90, 180, 270 DegreesRemovable Grille: YesShipping Weight: 47 lb (21.3 kg)Voice Coil: 2" 2-Layer copper​​

The 10 inch Digital Drive Plus subwoofer produces awe-inspiring, hard-hitting bass supported by Velodyne's exclusive patented accelerometer based High Gain Servo System to whittle distortion down to .5%. Its cutting-edge, highly sophisticated, 8-band Auto-EQPLUS technology assures not just low distortion but the most accurate bass available from any subwoofer available in the market today.And if you prefer, you can calibrate the subwoofer’s response with the 8 band parametric equalizer manually with its on-screen graphics, or computer readout using the front mounted USB port.You can even adjust the degree of control by the digital servo. The DD-10+ perfectly meshes audio engineering with the art of design to deliver a frequency response between 18.7 and 120 Hz, with a huge 1250 Watts RMS, 3000 Watts Dynamic, power amplifier, reproducing even the most challenging audio for applications from music to home theater to gaming. The DD-10+ deftly fills medium-sized rooms (2000-3500 cu. ft.) with incredibly accurate bass, perfectly optimized by the 8-band Auto-EQPLUS equalizer feature and remote-controlled presets to ensure you get the most out of your new audio equipment.If you refuse to compromise on performance and want to electrify your audio media in a medium-sized listening space, the DD-10+ is for you. Features:Patented accelerometer based High Gain Servo SystemThe industry's lowest distortion bass—under .5%One-Touch Auto-EQPLUS automates the seamless blend of subwoofer, system and roomUse your PC for manual adjustments and real time feedback of your bass performanceSophisticated cone design for fast, accurate motionSix-layer, custom wound voice coil assures better heat dissipationMassive motor structure for amazing low-frequency energy Specifications:Accessories: Remote Control, Digital Drive Plus Accessory Kit, Video CableAmplifier: 3000 watts Dynamic, 1250 watts RMS PowerAuto On/Off :YesCabinet Design: Sealed servo enclosureDimensions: (H/W/D) 14.2" x 13" x 16.6"Frequency Response: (+/-3 dB) 18.7 - 120 HzHiPass Crossover: 80 or 100 Hz at 6 dB/octaveLoPass Crossover: 40 Hz to 199 Hz (variable in 1 Hz increments) selectable slope Default: 80 Hz @ 24 dB/OctavePhase Control: 0, 180 DegreesRemovable Grille: YesShipping Weight: 77 lbs. (35 kg)Voice Coil: Six-layer, 65mmWarranty: (N. Am.) Two years (electronics & drivers - parts & labor)

The 12 inch Digital Drive Plus subwoofer produces awe-inspiring, hard-hitting bass supported by Velodyne's exclusive patented accelerometer based High Gain Servo System to whittle distortion down to .5%. Its cutting-edge, highly sophisticated, 8-band Auto-EQ+ technology assures not just low distortion but the most accurate bass available from any subwoofer available in the market today.And if you prefer, you can calibrate the subwoofer’s response with the 8 band parametric equalizer manually with its on-screen graphics, or computer readout using the front mounted USB port.You can even adjust the degree of control by the digital servo.The DD-12+ perfectly meshes audio engineering with the art of design to deliver a frequency response between 17 and 120 Hz, with a huge 1250 Watts RMS, 3000 Watts Dynamic, power amplifier, reproducing even the most challenging audio for applications from music to home theater to gaming.The 12 inch Digital Drive Plus fills large listening spaces (>3500 cu. ft.) with room-shaking, hyper-accurate bass., perfectly optimized by the 8-band Auto-EQPLUS equalizer feature and remote-controlled presets to ensure you get the most out of your new audio equipment.If your space is large and your need for power and perfection is great, the DD-12+ has what you’re looking for. Features:Patented accelerometer based High Gain Servo SystemThe industry's lowest distortion bass—under .5%One-Touch Auto-EQPLUS automates the seamless blend of subwoofer, system and roomUse your PC for manual adjustments and real time feedback of your bass performanceSophisticated cone design for fast, accurate motionSix-layer, custom wound voice coil assures better heat dissipationMassive motor structure for amazing low-frequency energy Specifications:Accessories: Remote Control, Digital Drive Plus Accessory Kit, Video CableAmplifier: 3000 watts Dynamic, 1250 watts RMS PowerAuto On/Off :YesCabinet Design: Sealed servo enclosureDimensions: (H/W/D) 15.8" x 14.4" x 18"Frequency Response: (+/-3 dB) 17.0 - 120 HzHiPass Crossover: 80 or 100 Hz at 6 dB/octaveLoPass Crossover: 40 Hz to 199 Hz (variable in 1 Hz increments) selectable slope Default: 80 Hz @ 24 dB/OctavePhase Control: 0, 180 DegreesRemovable Grille: YesShipping Weight: 85 lbs.Voice Coil: Six-layer, 65mmWarranty (N. Am.): Two years (electronics & drivers - parts & labor)

The 15 inch Digital Drive Plus subwoofer produces awe-inspiring, hard-hitting bass supported by Velodyne's exclusive patented accelerometer based High Gain Servo System to whittle distortion down to .5%. Its cutting-edge, highly sophisticated, 8-band Auto-EQ+ technology assures not just low distortion but the most accurate bass available from any subwoofer available in the market today. And if you prefer, you can calibrate the subwoofer’s response with the 8 band parametric equalizer manually with its on-screen graphics, or computer readout using the front mounted USB port. You can even adjust the degree of control by the digital servo. The DD-15+ perfectly meshes audio engineering with the art of design to deliver a frequency response between 14.6 and 120 Hz, with a huge 1250 Watts RMS, 3000 Watts Dynamic, power amplifier, reproducing even the most challenging audio for applications from music to home theater to gaming. The 15 inch Digital Drive Plus fills very large listening spaces (>5000 cu. ft.) with room-shaking, hyper-accurate bass., perfectly optimized by the 8-band Auto-EQ+ equalizer feature and remote-controlled presets to ensure you get the most out of your new audio equipment.If you want to fill a large listening space and demand the very best performance for a wide range of applications, the DD-15+ is ideal for your needs. Features:Patented accelerometer based High Gain Servo SystemThe industry's lowest distortion bass—under .5%One-Touch Auto-EQ+ automates the seamless blend of subwoofer, system and roomUse your PC for manual adjustments and real time feedback of your bass performanceSophisticated cone design for fast, accurate motionSix-layer, custom wound voice coil assures better heat dissipationMassive motor structure for amazing low-frequency energy Specifications:Accessories: Remote Control, Digital Drive Plus Accessory Kit, Video CableAmplifier: 3000 watts Dynamic, 1250 watts RMS PowerAuto On/Off :YesCabinet Design: Sealed servo enclosureDimensions: (H/W/D) 20" x 18.1" x 22.5"Frequency Response: (+/-3 dB) 14.6 - 120 HzHiPass Crossover: 80 or 100 Hz at 6 dB/octaveLoPass Crossover: 40 Hz to 199 Hz (variable in 1 Hz increments) selectable slope Default: 80 Hz @ 24 dB/OctavePhase Control: 0, 180 DegreesRemovable Grille: YesShipping Weight: 120 lbs. (55 kg)Voice Coil: Six-layer, 75mmWarranty (N. Am.): Two years (electronics & drivers - parts & labor)

The 18 inch Digital Drive Plus is the pinnacle of almost three decades of Velodyne subwoofer engineering expertise. Velodyne's exclusive patented accelerometer based High Gain Servo System whittles its distortion down to .5%. Its cutting-edge, highly sophisticated, 8-band Auto-EQ+ technology assures not just low distortion but the most accurate bass available from any subwoofer available in the market today. Quite simply, the DD-18+ is the biggest, baddest, cleanest, hardest-hitting sub in the world today. It is capable of a staggering amount of output; at 115 dB maximum, it’s 5 dB louder than a sonic boom. Needless to say, it also gets low—way, way low, with a frequency response between 14.4 and 120 Hz at 3dB down. You can calibrate the subwoofer’s response automatically or manually with the 8 band parametric equalizer with on-screen graphics, or computer readout using the front mounted USB port. You can even adjust the degree of control by the digital servo. The DD-18+ perfectly meshes audio engineering with the art of design to deliver a frequency response between 14.6 and 120 Hz, with a huge 1250 Watts RMS, 3000 Watts Dynamic, power amplifier, reproducing even the most challenging audio for applications from music to home theater to gaming.Unleash the authoritative power of the 18 inch Digital Drive Plus on your largest listening spaces and sink into the aural experience of over 99.5% accurate bass reproduction with unbelievable muscle, perfectly optimized by the 8-band Auto-EQ+ equalizer feature and remote-controlled presets to ensure you get the most out of your new audio equipment.If you want to fill a large listening space and demand the very best performance for a wide range of applications, the DD-18+ is ideal for your needs. Features:Patented accelerometer based High Gain Servo SystemThe industry's lowest distortion bass—under .5%One-Touch Auto-EQ+ automates the seamless blend of subwoofer, system and roomUse your PC for manual adjustments and real time feedback of your bass performanceSophisticated cone design for fast, accurate motionSix-layer, custom wound voice coil assures better heat dissipationMassive motor structure for amazing low-frequency energy Specifications:Accessories: Remote Control, Digital Drive Plus Accessory Kit, Video CableAmplifier: 3000 watts Dynamic, 1250 watts RMS PowerAuto On/Off: YesCabinet Design: Sealed servo enclosureDimensions: (H/W/D) 22.7" x20.7" 25.6" (58cm x 53cm x 65cm)Frequency Response: (+/-3 dB) 14.4 - 120 HzHiPass Crossover: 80 or 100 Hz at 6 dB/octaveLoPass Crossover: 40 Hz to 199 Hz (variable in 1 Hz increments) selectable slope Default: 80 Hz @ 24 dB/OctavePhase Control: 0, 180 DegreesRemovable Grille: YesShipping Weight: 140 lbs. (64 kg)Voice Coil: Six-layer, 75mmWarranty (N. Am.): Two years (electronics & drivers - parts & labor)

The SC-600 IW delivers budget-friendly, deep bass with low distortion in the 37 Hz to 120 Hz range at 3dB down from two 6.5" active drivers and two 12.5" x 3" passive drivers. It installs neatly behind a flush grille into both new construction and retrofits within a standard 2x4 framed wall. The SC-600 IW comes in a sealed cabinet, so you don't need to use any other boxes in the install. The SC-600 IW with its unique design vibrates walls 50% less than conventional in-wall designs.If you are buying an SC-600 IW subwoofer, you must power it with either an SC-600D or SC-602 amplifier to reap the benefits of the model-specific EQ settings; no other amplifier includes these. Features:Easy install in retro fit or new construction, with integrated cabinet; just cut, plug and playAmazing deep, powerful, low distortion bass performanceMinimum wall vibration via the unique triple vector designLow-profile design virtually disappears, fitting flush in a standard 2x4 wallVery reliable, with a strong 2-year parts and labor speaker warranty Specifications:Auto On/Off: NoCabinet Design: Active/PassiveColor: White VinylDimensions: (H/W/D) 18.6" x 16.5" x 4.3" 47.2 x 42 x 11 cmFrequency Response: (+/-3 dB) 23.25-250 Hz, 34.25-180 HzPhase Control: NoRemovable Grille: YesShipping Weight: 22 lbs. (9 kg)Voice Coil: 4-layer copperWarranty (N. Am.): Two years (drivers - parts & labor)

The Magneplanar Bass Panel (DWM) is a dipole, thin-film, planar/magnetic bass panel. It is two bass drivers in one panel. Two "voice coil" grids drive one bass diaphragm. The Bass Panel is essentially a small section out of the 20.1 and 20.7 bass drivers. But, please don't call it a "subwoofer". Subwoofers are a separate category from woofers.Subwoofers are intended for below 40 Hz and are known as "slow" and "muddy" when used above 40 Hz. Subwoofers can be adjusted higher than 40 Hz, but you will achieve better sound by using the Bass Panel to optimize the bass of your Maggies. The DWM Bass Panel has no problem integrating with a full-range Maggie because it is "all Maggie".But, the Maggie Bass Panel affords far more than increasing bass/midbass output. It is common knowledge that multiple subwoofers can be used to fine-tune and smooth the bass. What is not common knowledge is this technique can be used up to approximately 200 Hz. Through trial-and-error, the position of mobile bass panels can smooth both phase and amplitude response for the preferred listening position. Often the ideal listening position for imaging is not the optimum position for the smoothest bass/midbass.Standing waves can be trouble-some, creating peaks and dips in the bass response. The Maggie Bass Panel can help fine-tune any of our models, even our flagship 20.7s. Specifications:Planar-magnetic dipole bass panelFrequency Response: 40-200 Hz*Sensitivity: 86 dB @2.83V/1 Meter/50 HzImpedance: 4 OhmDimensions: 19.25Hx22.5Wx1.25D (inches)

The down-firing port on the Impact-12 gives more bass output with less distortion than similarly priced subwoofer from other companies. With its 275 watts of amplifier focused on the 29 Hz to 140 Hz frequencies, you get a ton of bass for you dollar.You can blend the Impact-12 with your satellite speakers using the adjustable low pass crossover frequency feature. All this great sound is wrapped up in an attractive black ash wood grain colored cabinet with black gloss trim. Features:Compact, stylish cabinet; high-value subwooferHigh quality, long throw drivers12" forward firing coated fiber wooferDown-firing port minimizes distortion2" copper-wound voice coils for exceptional reliability“Green” MDP amp rated at 275 watts Dynamic power Specifications:Amplifier: 165 watts RMS, 275 watts Dynamic PowerAuto On/Off: YesDimensions: (H/W/D) 15.1" x 14.2" x 18.9" (38.4 x 36 x 48 cm)Frequency Response: (+/-3 dB) 29-140 HzHiPass Crossover: Full RangeLoPass Crossover: 50 Hz-200 HzPhase Control: 0,180 DegreesRemovable Grille: YesShipping Weight: 33 lbs. (15 kg)Size: LargeVoice Coil: 2" dual layer copper-wound

Thunderous bass. Wireless connectivity.Love your new SoundTouch soundbar but want to kick the performance up a notch? Add the Acoustimass 300 wireless bass module—it's the difference between hearing bass and feeling thunder. Designed exclusively for the SoundTouch 300 soundbar, it's the best Acoustimass module we've ever designed for any of our home cinema systems. In fact, it's the best performance you can get for a subwoofer this size. It connects wirelessly to the soundbar and provides a more immersive experience for everything you listen to or watch.     A statement in sound and styleWith its premium glass-top finish, the Acoustimass 300 wireless module offers a sophisticated look you won't find in typical subwoofers or home cinema equipment. Of course, this isn't typical equipment. This newly designed subwoofer delivers a dynamic range of bass from a powerful driver and generously sized port with QuietPort technology that virtually eliminates distortion.  

All the audiophile-like transparency of New Bronze’s low-distortion design regimen concentrated in the bass domain. This is New Bronze bass, deeply provisioned, authentically proportioned and dynamically fleet of foot, re-tooled from the ground up to punctuate the sound of every New Bronze system with stunningly natural bass transients, timed to perfection.The sophisticated W10 subwoofer is a New Bronze original, featuring an exclusive trinity of uprated amplifier topology, powerful DSP processing and new long-throw driver design. Advanced switch-mode power conversion techniques, custom DSP tuning and a massive power reservoir combine to generate enormous dynamic headroom from the Class D power-pack, allowing the driver to drop low and punch hard without distortion for a truly sensational deep bass experience.A down-firing 10” ABR (Auxiliary Bass Radiator) ensures that with the same compact footprint as its predecessor, the W10 delivers an incredible 6dB greater SPL at 40Hz. Choose how you enjoy the W10’s prodigious bass energy with pre-set EQ settings for music, movie or impact.Specifications:Low Frequency Limit: 30HzUpper Frequency Limit: 40-120Hz (Variable Low Pass filter)Low Pass Filter Alignment: 12dB/ Octave variable + 12dB/ Octave Fixed @ 150HzAmplifier Output220W R.M.S Amplifier ClassificationClass D with Switch mode PSUDrive Unit Complement1 x 10″ C-CAM® Long throw subwoofer driver + 1 x 10” flat panel ABRExternal Dimensions: (H x W x D)320 x 320 x 330 mm12 5/8 x 12 5/8 x 13 inches(364 x 320 x 364 mm14 5/16 x 12 5/8 x 14 5/16 inches inc grille amp & feet)Input Impedance: 20kΩStandby power consumption: 0.5W (ErP approved)Mains Input Voltage110-120Vac – 50-60Hz220-240Vac – 50-60HzElectronic auto-selectWeight: 12.9kg (28lb 6oz)COLORS: White ash, black oak, walnut, rosemah, natural oak

The X301 subwoofer is packed with significant technological advances. A forward firing driver for amazing punch and attack, combined with a state-of-the-art Auxiliary Bass Radiator (ABR) to deliver thunderous levels despite their compact and discrete design.The X301 is an extremely efficient and very powerful subwoofer housed in tiny cabinets, their slender size deceives the eye.Still at only 28cm (11”) square this 300W powerhouse is smaller than most typical subwoofers. But with an 8” active woofer matched to an auxiliary bass radiator it will erupt your music and movies to life with immersive punch and power.The Minx subwoofers offer complete rear panel control of ‘gain’, ‘phase’ and ‘crossover frequency’, unlike many other style subwoofers which give little or no adjustment in these areas. With these true hi-fi capabilities, regardless of your room’s shape and size Minx’s simple set-up adjustments ensure your system is perfectly customised for placement almost anywhere.Features:Powerful DSP design delivering awesome performance from the smallest footprint possiblePowerful 300W digital amplifiersOne piece aerospace grade aluminium cones move air with incredible efficiency.DSP design allows far smaller cabinet construction than comparative subwoofers.Supplied with removable grillesFull rear panel control of gain, phase and crossover frequency allowing optimum integration and roompositioningDriver plus ABR (Auxillary Bass Radiator)configuration. ABRs replace bass ports to eliminateair noise at high levelsScratch resistant high gloss lacquer available in black or white finishes.​​Specifications:Power Output: 300WFrequency Response: 31Hz (-6dB) – 200HzCrossover Active: – variable 50Hz-200HzDrivers: 1 x 8" subwoofer1 x 8" passive radiatorDimensions: 311 x 266 x 278mmWeight: 7.5Kg (16.5lbs)Finishes: High gloss white  

The X301 subwoofer is packed with significant technological advances. A forward firing driver for amazing punch and attack, combined with a state-of-the-art Auxiliary Bass Radiator (ABR) to deliver thunderous levels despite their compact and discrete design.The X301 is an extremely efficient and very powerful subwoofer housed in tiny cabinets, their slender size deceives the eye.Still at only 28cm (11”) square this 300W powerhouse is smaller than most typical subwoofers. But with an 8” active woofer matched to an auxiliary bass radiator it will erupt your music and movies to life with immersive punch and power.The Minx subwoofers offer complete rear panel control of ‘gain’, ‘phase’ and ‘crossover frequency’, unlike many other style subwoofers which give little or no adjustment in these areas. With these true hi-fi capabilities, regardless of your room’s shape and size Minx’s simple set-up adjustments ensure your system is perfectly customised for placement almost anywhere.Features:Powerful DSP design delivering awesome performance from the smallest footprint possiblePowerful 300W digital amplifiersOne piece aerospace grade aluminium cones move air with incredible efficiency.DSP design allows far smaller cabinet construction than comparative subwoofers.Supplied with removable grillesFull rear panel control of gain, phase and crossover frequency allowing optimum integration and roompositioningDriver plus ABR (Auxillary Bass Radiator)configuration. ABRs replace bass ports to eliminateair noise at high levelsScratch resistant high gloss lacquer available in black or white finishes.​​Specifications:Power Output: 300WFrequency Response: 31Hz (-6dB) – 200HzCrossover Active: – variable 50Hz-200HzDrivers: 1 x 8" subwoofer1 x 8" passive radiatorDimensions: 311 x 266 x 278mmWeight: 7.5Kg (16.5lbs)Finishes: High gloss black  

The X201 subwoofer is packed with significant technological advances. A forward firing driver for amazing punch and attack, combined with a state-of-the-art Auxiliary Bass Radiator (ABR) to deliver thunderous levels despite their compact and discrete design.The X201 is an extremely efficient and very powerful subwoofer housed in tiny cabinets, their slender size deceives the eye.At just 20cm (9") square, X201 is one of the world’s smallest subwoofers and is incredibly easy to accommodate. And like all Minx subwoofers, it features a range of simple controls to allow placement almost anywhere...Specifications:Power Output: 200W rmsFrequency Response: 39Hz (-6dB) – 200HzCrossover: Active – variable 50Hz-200HzDrive units: 1 x 6.5″ subwoofer, 2 x 6.5″ passive radiatorsDimensions (H x W x D): 219 x 210 x 222mm (8.6 x 8.3 x 8.7″)Weight: 5.0Kg (11.0lbs) 

The X201 subwoofer is packed with significant technological advances. A forward firing driver for amazing punch and attack, combined with a state-of-the-art Auxiliary Bass Radiator (ABR) to deliver thunderous levels despite their compact and discrete design.The X201 is an extremely efficient and very powerful subwoofer housed in tiny cabinets, their slender size deceives the eye.At just 20cm (9") square, X201 is one of the world’s smallest subwoofers and is incredibly easy to accommodate. And like all Minx subwoofers, it features a range of simple controls to allow placement almost anywhere...Specifications:Power Output: 200W rmsFrequency Response: 39Hz (-6dB) – 200HzCrossover: Active – variable 50Hz-200HzDrive units: 1 x 6.5″ subwoofer, 2 x 6.5″ passive radiatorsDimensions (H x W x D): 219 x 210 x 222mm (8.6 x 8.3 x 8.7″)Weight: 5.0Kg (11.0lbs) 

Promising the astonishing low frequency resolution of the 380 with the added depth, impact and control of a larger bass engine, the Radius 390 demolishes assumptions of size versus performance. With every earth-shaking transient, you’ll be more convinced that the compact 390 is truly ‘ground-breaking’ in form and function. A system of twin colour-coded 10” C-CAM active/ABR drivers is powered by a 220W Class D amplifier to expand levels of output and extension, releasing a rich layer of penetrating bass, mesmerising in its consistency and scale. You’ll get agility as well, for rhythmic depth with music, and dynamic reinforcement in home theatre systems - all this from a beautiful little cube that liberates living space. In tune with Radius philosophy the 390 is perfect for lifestyle but sonically it’s in a class of its own. Enjoy rapid EQ optimisation from Impact, Music and Movie settings, and system automation via the 12V trigger.Features:  18mm MDF cabinet construction with internal bracing  Cool-running 220W Class D amplifier with switch mode power supply (SMPSU)  Twin side-firing 10” C-CAM drivers - one active and one passive ABR    Low pass filter switch – for LFE or Stereo input selection  Power switch with ON – Auto- Off/ trigger settings  Stereo/ LFE RCA inputs  3 x Pre-set EQ settings – Music/Movie/ImpactSpecifications:System Format: Active sub-woofer system – Auxiliary (ABR) loading. 18mm MDF cabinet Low Frequency Limit: 30Hz (- 6dB) Upper Frequency Limit: Variable 40 – 120 Hz @ 24dB/Octave Amplifier Power Output: 220 Watts @ 1% THD+N Amplifier Classification: Class D amplifier with Switch mode power supply (SMPSU) Bass EQ Switch: Music/ Movie/ Impact Phase Control: 0 & 180 degrees Auto Sensing: Line Level >3.5mV Input Level Requirements: Standby after approximately 15 minutes if no signal sensed Driver Compliment: 1 x 10” (250mm) C-CAM long throw driver,1 x 10” (250mm) Auxiliary bass radiator Input Impedance: > 20K Ohms Mains Input Voltage: AC 110 - 120 V ~ 50/60Hz;  AC 220 - 240 V ~ 50/60Hz  (Factory Region Preset) Dimensions including amp & feet (H x W x D): 348 x 330 x 345mm, (1311/16 x 13 x 129/16 Inches) Connections: Stereo RCA in, LFE in, 12v Trigger in  (3.5mm mono mini-jack) 12v Trigger Input: 5 - 12v via 3.5mm mono mini-jack socket Power Consumption: 220 Watts / 0.5 Watts in Standby (ErP approved) Weight (Unpacked):  13.76Kg (30lb 4oz)

Since the last Radius series we’ve applied our research and development to the challenge of subwoofer design. It’s relatively easy to produce large bass in a large box, but finding the optimum mix of parameters required to generate genuinely deep dynamic bass from a space efficient Radius cabinet requires a vastly more innovative approach. We’re confident that the ultra-compact Radius 380 will elevate your expectations of what’s possible in a small enclosure: the Radius 380 and its companion 390 rewrite the rules.Within the 380’s diminutive cube, twin side-firing 8” C-CAM drivers - one active and one passive ABR - work in tandem with a powerful 200W cool-running Class D amplifier (double the power of its predecessor) to deliver a seismic bass foundation for films and music, distinguished by an intoxicating blend of depth and speed. Tuned for an utterly dynamic result with Radius satellites in film and music systems, the 380 also offers Impact, Movie and Music pre-sets for easy EQ operation. The drivers have no grilles but are colour-coded to coordinate with cabinet finish. A 12V trigger syncs the 380 with other AV components when the system is activated. Features:  18mm MDF cabinet construction with internal bracing  Cool-running 200W Class D amplifier with switch mode power supply (SMPSU)  Twin side-firing 8” C-CAM drivers - one active and one passive ABR  Low pass filter switch – for LFE or Stereo input selection  Power switch with ON – Auto- Off/ trigger settings  Stereo/ LFE RCA inputs  3 x Pre-set EQ settings – Music/Movie/ImpactSpecifications:System Format: Active sub-woofer system – Auxiliary (ABR) loading. 18mm MDF cabinetLow Frequency Limit: 30Hz (- 6dB)Upper Frequency Limit: Variable 40 – 120 Hz  24dB/OctaveAmplifier Power Output: 200 Watts  1% THD+NAmplifier Classification: Class D amplifier with Switch mode power supply (SMPSU)Bass EQ Switch: Music/ Movie/ Impact Phase Control 0 & 180 degrees Auto Sensing Line Level >3.5mVInput Level Requirements: Standby after approximately 15 minutes if no signal sensedDriver Compliment: 1 x 8” (200mm) C-CAM long throw driver 1 x 8” (200mm) Auxiliary bass radiatorInput Impedance: > 20K OhmsMains Input Voltage: AC 110 - 120 V ~ 50/60Hz;  AC 220 - 240 V ~ 50/60Hz  (Factory Region Preset)Dimensions including amp & feet (H x W x D): 308 x 290 x 305mm (121/8 x 117/16 x 12 Inches)Connections: Stereo RCA in, LFE in, 12v Trigger in  (3.5mm mono mini-jack)12v Trigger Input: 5 - 12v via 3.5mm mono mini-jack socketPower Consumption: 200 Watts / 0.5 Watts in Standby  (ErP approved)Weight (Unpacked): 10.16Kg (22lb 6oz)

The Completion…A pair of LS1s stereo subwoofers integrate seamlessly with the LS1. Its phase corrected crossover at 70 Hz is already built in the LS1, so just adding the subs turns the system into a unique phase coherent three-way system. Although the LS1 on its own can play down to 40 Hz with quite impressive power, the bottom octave down to 20 Hz is hard to produce with a two-way loudspeaker system. Especially classical music does benefit from a balanced reproduction of these ultra low frequencies. Also, both professionals who need to check their mix at raised SPL and regular Hi-Fi enthusiasts who enjoy their music at realistic levels, will value the lower LS1 system distortion offered by the LS1s option.“Adding the LS1s subs turns the LS1 system into a unique phase coherent three-way system.”At low frequencies, wavelengths are so large that the speaker's orientation does not matter. This fact offered us the opportunity to elegantly fit the LS1s between the legs of an LS1, facing upwards. To match the immaculate quality of the LS1, we selected a top notch Peerless woofer and a 400W class D amplifier of Hypex fame.More info can be found at the LS1 page.Features:Linear response down to 20 HzTurns the LS1 into a powerful 3-way systemDSP controlled frequency curvePhase corrected crossover at 70 HzPeerless woofer and 400W class D amplifierMains outlet for LS1 minimizes cable clutter

Active subwoofer 50 watt. TECHNICAL SPECIFICATIONS: Frequency Response: 35 - 150 HzCrossover frequency: 50 - 150 Hz.Speaker Diameter: 165mmInputs: Line in and high passDimensions: 80 x 250 x 280 mm,Weight: 5.3 kg. 

The ideal complement to the ESPRIT range for forming an audio-video system, this subwoofer was designed to favor speed and dynamics. Its cube shape enables it to fit perfectly into any living space. METEOR 0.1 Tc includes a remote control for adjusting both frequency and level.TECHNICAL SPECIFICATIONS: TypeActive subwooferNumber of drivers                        1Diameter8" / 21 cmFrequency range35 Hz – 160 KHz (+/- 3 dB)Amplifier power100 W RmsRemote controlyesDimensions370 x 320 x 320 mmweight14,5 kg 

This subwoofer’s wireless connection system makes it unique and its 11” driver will give you all the bass power you need. The loudspeaker comes with a remote control allowing you to easily adjust settings at any moment.TECHNICAL SPECIFICATIONS: Loudspeaker typeLoudspeaker typeNumber of drivers1Diameter11" / 28 cmFrequency range                              28 Hz – 160 KHz (+/- 3 dB)Amplifier power300 WRemote controlyesCabinet dimensions430 x 380 x 423 mmweight46,2 lbs / 21 kg 

Adam Sub 7 was expressly designed to pair with A5 monitors. It boasts both XLR and RCA inputs as well as a modest footprint (like the A5s), making it a perfect addition to any monitoring environment - especially where space is at a premium.  You'll enjoy frequency reproduction all the way down the 30Hz, and even a wireless remote control so you can adjust the volume and the crossover frequency comfortably from your main listening position. Available in three colors: Matte Black, Piano Black, and Piano White - you'll give your mixes the low-end attention and definition they need with the ADAM Sub7.

Adam Sub 8 - 8" sub woofer with coated paper membrane, frequency response: 28Hz-150Hz (±3dB), adjustable crossover frequency (50-150Hz), variable input gain (-40 to +12dB), balanced XLR inputs.  Dimensions: 410 x 260 x 380mm (HxWxD). Weight: 12kg.

A top quality subwoofer  equipped with a 15-inch double voice coil chassis which is built into a sealed housing with a double wall design.Specifications:  One 15" dual coil driver in sealed, dual wall enclosure.Frequency response: Room dependant. Typically flat to 23 Hz.SPL: 90 dB 1W/1mImpedance: 4/8/16 OhmsDimensions: 18" H x 18"W x 19.4" D (45,6cm x 45,6cm x 49,3cm)Weight: 64.4 lbs (29 kg)

The SW 1000 Be subwoofer is the redesigned version of the Electra Be subwoofer to ensure compatibility with the other loudspeakers in the Sopra line.It is equipped with a 13" (33cm) "W" cone speaker driver (high rigidity for no distortion, even at high volumes), a high-power 600 W RMS BASH® amplifier and a front laminar port (no dynamic bass compression).The 24-bit digital processor (DSP) offers a large control panel with settings for adapting the sub to various listening rooms. The SW 1000 Be offers very high performance with a bass cut-off frequency of 18 Hz and an SPL of 118 dB.Several SW 1000 Be subwoofers can be linked up. ΤECHNICAL SPECIFICATIONS: TypeActive bass-reflex subwoofer. Standard finishesBasalt - Champagne - Slate Grey On demand finishesOther finishes subject to estimate Drivers33cm woofer Frequency response (+or-3dB)20Hz - 150Hz Low frequency point18Hz Recommended amplifier power600W (750W max.) BASH® amplifier. Subwoofer featuresAdjustable LPF: 50Hz to 150Hz (24dB/oct.), 48dB/oct. adjustable subsonic filter, adjustable phase, Boost mode, Night mode, 3 user memories, LFe/Stereo/Digital enter. Dimensions (HxWxD)21-1/16x19-11/16x17" Net weight92.4Ibs (42kg) 

DescriptionStylish Danish Hi-FiTangent’s Spectrum range of affordable hi-fi and home theatre loudspeakers offer typically Danish contemporary, stylish designs fused with high-end audio quality from compact enclosures … to create the very best in two and multi-channel applications.Latest Technology The range benefits from latest-technology drive units carefully selected by Tangent’s acoustic engineers, including a wide dispersion 25mm soft fabric dome tweeter, together with a 110mm or 130mm long throw paper coned bass driver … or an 200mm bass driver featured in the front firing subwoofer.Danish Speaker DesignThe compact, stylish enclosures boast a solid, inert construction to reduce cabinet colouration and resonance. Available in attractive midnight black or polar white highly durable matt satin finishes, all drive units are protective with colour-matched, integrated mesh grilles. Contrasting walnut base plinths complete the unique aesthetic appeal across the range.Spectrum XSW-8The XSW-8 subwoofer is a compact front firing bass module designed to enhance bass performance and perfectly completes the Spectrum’s 5.1 packaged system. Also using a sealed enclosure for ultimate low-end power, the XSW-8 uses a 200 mm bass only driver and a 90 watt integral amplifier to produce low-end frequencies down to 31Hz. The impressive features list also includes volume level, phase switching and variable crossover.Make it a SystemComplete your system with the new Spectrum XC Centre speaker and Spectrum X4, X5 or X6 for a full surround setup. 

The Cub Evo is an iconic subwoofer, designed to provide high-quality 5.1 sound. The Cub3 is a compact product that incorporates only those functions strictly necessary for the purpose. This makes it extremely simple to install and use, and there is no need to compromise on acoustic performance. For optimal output, the Cub3 has a 21cm bassreflex woofer and modern 150 watt BASH amplification, allowing it to reproduce every nuance of the bass register. SPECS Exceptional performances in ultra compact size 8" high power High efficiency, high power, 150 W BASH amplifier Aerodynamic port for optimal performance

The Planet Sub has the same DNA as Elipson’s Planet line: its exceptional design and uncompromising sound fidelity bear witness to its prestigious lineage. Integrating a 20 cm speaker alive with 200 watt amplification, this bass unit offers musical excellence and a sense of versatility so it’s at home as part of your stereo setup and it’s just as comfortable anchoring your home-cinema configuration. Uniting elegance and performance, Planet Sub guarantees to fit in harmoniously with your Elipson spheres.Specifications:With grill and terminal (W x H x D): 316 x 393 x 316 mm System: 1 wayFrequency range: 30 - 240 HzMax music power: 200 WattsVoltage: 110-220V / 220-240VAC - 200W WattsAmplifier type: DIntegrated Amplifier power: 200Terminal type: Single wiringTerminal finish: Silver platedInput: LineEnclosure: Bass ReflexPhase: 0/180

The Planet Sub has the same DNA as Elipson’s Planet line: its exceptional design and uncompromising sound fidelity bear witness to its prestigious lineage. Integrating a 20 cm speaker alive with 200 watt amplification, this bass unit offers musical excellence and a sense of versatility so it’s at home as part of your stereo setup and it’s just as comfortable anchoring your home-cinema configuration. Uniting elegance and performance, Planet Sub guarantees to fit in harmoniously with your Elipson spheres.Specifications:With grill and terminal (W x H x D): 316 x 393 x 316 mm System: 1 wayFrequency range: 30 - 240 HzMax music power: 200 WattsVoltage: 110-220V / 220-240VAC - 200W WattsAmplifier type: DIntegrated Amplifier power: 200Terminal type: Single wiringTerminal finish: Silver platedInput: LineEnclosure: Bass ReflexPhase: 0/180

The Sub 1000 F subwoofer has been designed for Home Cinema use in the purest Focal tradition.A technological masterpiece, it has a 30 cm diameter Flax membrane bass speaker cone. The stiffness and lightness of this environmentally-friendly textile mean it produces an extremely well defined, distortion-free sound. The "Dual Magnet" dual driver provides phenomenal power while ensuring excellent linearity. The Sub 1000 F has an integrated 1000 watt BASH® super-powerful amplifier to let the 30 cm woofer unleash its full potential. Finally, its sealed construction offers an extended bass response, a very compact size and an absence of interference, all leading to a pure, harmonious sound.This loudspeaker is perfect for faithfully reproducing your film soundtracks with ease, making it the proud complement to your Aria 900 speakers.COMPLETE YOUR HOME CINEMA SYSTEM WITH POWERFUL, CONTROLLED BASS The subwoofer is vital in home cinema systems, for truly realistic multichannel reproduction. The sound effects of soundtracks cannot be rendered by central and surround speakers alone. The bass is a separate channel and not merely an add-on. It contains its own effects data based on energy and dynamics. This data cannot be properly reproduced by conventional speakers, no matter what their size or capacity to reproduce the bass. The Sub 1000 F subwoofer is the perfect unit to reproduce these sounds thanks to its over-specified 1000 watt amplification power.What is more, recent blockbusters feature soundtracks that are increasingly rich in the bass and even sub-bass, with signals going lower and lower in the sound spectrum. For this reason, this register becomes more and more challenging to reproduce perfectly with bass reflex subwoofers. That is why the Sub 1000 F has a sealed enclosure to meet these new demands.ULTRA-POWERFUL AMPLIFIER Its powerful 1000 watt BASH® amplifier ensures the Sub 1000 F speaker can express its full potential.Besides its power, the amplifier has a range of functionalities and settings to help you adjust the bass to suit your room or home cinema space: Sound volume adjustment, active variable low-pass filter for adjustment of high cut-off frequency from 40 to 160 Hz, phase inverter for phase adjustment, and automatic stand-by mode.In terms of connectivity, the Sub 1000 F has an LFE input for multi-channel audio/video amplifiers and a "low level" stereo RCA input for 2 channel amplifiers.FLAX MEMBRANE FOR REMARKABLE DEFINITION OF BASS FREQUENCIESThe speaker cone in this subwoofer uses Flax Technology. Flax is an environmentally-friendly textile with astonishing structural properties that make it particularly suitable for sound production: It is light, stiff and well damped. In general terms, flax membranes provide greater neutrality of timbre and better sound definition.Evolved from the Flax cones developed for the Aria 900 speaker range, the cone membrane in the Sub 1000 F features a new, even more rigid construction. Two sheets of 160 g/m2 fibre glass and a 250 g/m2 flax core. It is able to withstand the high demands associated with subwoofers.A SPEAKER THAT IS OPTIMISED FOR DYNAMIC, CONTROLLED BASSThe Sub 1000 F subwoofer also features a coil/driver unit that is optimised to keep the coil temperature as low as possible. This means the speaker gives well articulated bass, better dynamics and considerable SPL power (103.5 dB / 1 m @ 40Hz).Focal's Research & Development team developed a custom spider/suspension for the Sub 1000 F. Its dynamic behaviour is perfectly controlled, meaning that the bass is always controlled too, even with very long travel (up to 43 mm). 

The intense and deep sound of the Sub Air complements all Focal 5.1 systems. The wireless technology makes integration into interiors easy, removing all constraints due to cable length. The flat and compact design allows you to fit it into all kinds of spaces.Easy to use and install, the Sub Air turns on at your command and turns itself off when no more sound is being produced.Its Wi-Fi radio connectivity puts a permanent end to the eternal question of where to put the cables. A discreet emitter is connected to the rear of the amplifier and makes cabling entirely unnecessary.Its highly innovative design makes the Sub Air a quality, practical and elegant response to your listening requirements. Do not be deceived by its anti-conformist appearance, as this beautiful object is a genuine high-performance subwoofer, fitted with a 21cm bass-reflex boombox for increased effect and modern 150 watt BASH amplification. Its shape was designed so make it an object of desire that people would no longer seek to hide, despite its compact nature. Its luxurious, authentic lacquer finish further reinforces its appeal. Above all, however, its shape allows it to be harmoniously integrated with your interior, whether on the floor or fitted to the wall using the supplied mounting kit. Features:Focal design and soundIdeal for Home Theater systemsFlexibility of installation / wireless connectionHigh-gloss finishCan be wall-mounted, takes up little floor spaceFocal’s flattest subwooferEasy and quick to install: synchronization button, phase and volume adjustmentWireless Transmitter included : LFE and Left/Right Input

The intense and deep sound of the Sub Air complements all Focal 5.1 systems. The wireless technology makes integration into interiors easy, removing all constraints due to cable length. The flat and compact design allows you to fit it into all kinds of spaces.Easy to use and install, the Sub Air turns on at your command and turns itself off when no more sound is being produced.Its Wi-Fi radio connectivity puts a permanent end to the eternal question of where to put the cables. A discreet emitter is connected to the rear of the amplifier and makes cabling entirely unnecessary.Its highly innovative design makes the Sub Air a quality, practical and elegant response to your listening requirements. Do not be deceived by its anti-conformist appearance, as this beautiful object is a genuine high-performance subwoofer, fitted with a 21cm bass-reflex boombox for increased effect and modern 150 watt BASH amplification. Its shape was designed so make it an object of desire that people would no longer seek to hide, despite its compact nature. Its luxurious, authentic lacquer finish further reinforces its appeal. Above all, however, its shape allows it to be harmoniously integrated with your interior, whether on the floor or fitted to the wall using the supplied mounting kit. Features:Focal design and soundIdeal for Home Theater systemsFlexibility of installation / wireless connectionHigh-gloss finishCan be wall-mounted, takes up little floor spaceFocal’s flattest subwooferEasy and quick to install: synchronization button, phase and volume adjustmentWireless Transmitter included : LFE and Left/Right Input