Turntables

This turntable makes use of traditional frame design which was established by the famous turntable manufacturers of the 50's and 60's. It uses a compact simple and elegant form factor. The Classic incorporates a combination of approved belt drive design using a low noise AC motor with an ultra-precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability. Advanced technology is used for decoupling and the completely new designed tone-arm Specifications:Belt drive with manual speed control 33/45 rpmHeight adjustable decoupling feetPrecision balanced TPE*-damped aluminium-platter / felt matMetal/MDF sandwich chassis floating on TPE* suspension9” carbon/aluminium tonearm with MM & MC capabilityJapanese ball bearing (base of tonearm)Integrated central vertical cable outlet for unhindered arm movementUltra low friction Zircon pin-point cardan bearings (top & side)Azimuth and VTA fully adjustableTPE damped counterweightAvailable with 2M Silver phono cartridgeClassic woodn chassis in 3 matt finishes (walnut, rose nut, eucalyptus)Dustcover included

This turntable makes use of traditional frame design which was established by the famous turntable manufacturers of the 50's and 60's. It uses a compact simple and elegant form factor. The Classic incorporates a combination of approved belt drive design using a low noise AC motor with an ultra-precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability. Advanced technology is used for decoupling and the completely new designed tone-arm Specifications:Belt drive with manual speed control 33/45 rpmHeight adjustable decoupling feetPrecision balanced TPE*-damped aluminium-platter / felt matMetal/MDF sandwich chassis floating on TPE* suspension9” carbon/aluminium tonearm with MM & MC capabilityJapanese ball bearing (base of tonearm)Integrated central vertical cable outlet for unhindered arm movementUltra low friction Zircon pin-point cardan bearings (top & side)Azimuth and VTA fully adjustableTPE damped counterweightAvailable with 2M Silver phono cartridgeClassic woodn chassis in 3 matt finishes (walnut, rose nut, eucalyptus)Dustcover included

This turntable makes use of traditional frame design which was established by the famous turntable manufacturers of the 50's and 60's. It uses a compact simple and elegant form factor. The Classic incorporates a combination of approved belt drive design using a low noise AC motor with an ultra-precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability. Advanced technology is used for decoupling and the completely new designed tone-arm Specifications:Belt drive with manual speed control 33/45 rpmHeight adjustable decoupling feetPrecision balanced TPE*-damped aluminium-platter / felt matMetal/MDF sandwich chassis floating on TPE* suspension9” carbon/aluminium tonearm with MM & MC capabilityJapanese ball bearing (base of tonearm)Integrated central vertical cable outlet for unhindered arm movementUltra low friction Zircon pin-point cardan bearings (top & side)Azimuth and VTA fully adjustableTPE damped counterweightAvailable with 2M Silver phono cartridgeClassic woodn chassis in 3 matt finishes (walnut, rose nut, eucalyptus)Dustcover included

This special collaboration between Pro-Ject Audio Systems and the Universal Music Group features one of the most influencing artists of modern history, former Beatles member George Harrison! The turntable used is Essential III, the evolution of a milestone. It features high quality and audiophile components, such as an Ortofon OM10 cartridge, a precision diamond cut aluminum pulley, top notch MDF chassis, an acrylic platter or a completely redesigned motor control. Its sound is both lively and relaxing, musical and detailed just like the music from George Harrison, therefore they are perfect partners in crime.  The artwork on the turntable was created by Studio Number One. The original design was created by Shepard Fairey, one of the most respected street artists around, for the Harrison family. It features a distinctive portrait of George Harrison and forms together with the Indian patterns and the analog mixing console (below the acrylic platter) with a unique look.  This one of a kind masterpiece is limited to 2500 pieces worldwide.  Features:Special edition of Essential III  Limited to 2500 pieces worldwide!  Acrylic platter  Artwork by respected street artist Shepard Fairey!  Belt drive with synchronous motor and silicone belt  Diamond cut aluminum drive pulley  Chassis made of resonance in-sensitive MDF  Integrated DC-powered motor control minimizes motor vibration and guarantees speed stability  Low tolerance platter bearing with stainless steel spindle  8,6” aluminum tonearm with sapphire bearings  Ortofon OM10 cartridge pre-mounted  High-quality semi-balanced Connect it E phono interconnect With gold-plated RCA connectors included  Special decoupling feet  Dust cover included   Specifications:Speed: 33, 45 (manual speed change)Principle: belt driveSpeed variance: 33: 0,70% 45: 0,60%Wow & flutter: 33: 0,21% 45: 0,19%Platter: 300mm acrylic with felt mat (0,8kg)Main bearing: stainless steelEffective arm length: 218,5 mmOverhang: 22,0mmEffective tonearm mass: 8,0grCounterweight for mass: 3 - 5,5g (included)Tracking force range: 0 - 25mn (OM5 18mn recommended)Included accessory: power supply, dust coverPower consumption: 4,5 watts maxDimensions: 420 x 112 x 330mm (WxHxD)Weight: 5,0 kg net 

Essential III offers a variety of enhancements compared to its successful predecessors, such as a diamond-cut aluminum drive pulley, a resonance-optimized MDF main platter, and MDF chassis. The refined, high-precision platter bearing has significantly lower tolerances than Essential II. Essential III is the audiophile entry turntable! The setup is very simple, the included Phono RCA cable, Connect it E, sounds far above its price range. Equipped with the high-quality pickup OM10 by the phonographic cartridge pioneer Ortofon, Essential III delivers lively, balanced and highly involving sound that will delight every vinyl lover.   Essential III comes in the aesthetic high gloss colors black, red and white.   Specifications:Belt drive with synchronous motor and silicone belt  Diamond cut aluminium drive pulley  Chassis & platter made of resonance in-sensitive MDF  Integrated DC-powered motor control minimizes motor vibration and guarantees speed stability  Low tolerance platter bearing with strainless steel spindle  8,6” aluminum with sapphire bearings  Ortofon OM10 cartridge pre-mounted  High-quality semi-balanced Connect it E phono interconnect with gold-plated RCA connectors included  Special decoupling feet  Dust cover included  High-gloss colour options: black, red, white  Counterweight for mass : 3 - 5,5g (included)Tracking force range: 0 - 25mn (OM5 18mn recommended)Included accessory: power supply, dust coverPower consumption: 4,5 watts maxDimensions: 420 x 112 x 330mm (WxHxD)Weight: 5,0 kg net

Essential III offers a variety of enhancements compared to its successful predecessors, such as a diamond-cut aluminum drive pulley, a resonance-optimized MDF main platter, and MDF chassis. The refined, high-precision platter bearing has significantly lower tolerances than Essential II. Essential III is the audiophile entry turntable! The setup is very simple, the included Phono RCA cable, Connect it E, sounds far above its price range. Equipped with the high-quality pickup OM10 by the phonographic cartridge pioneer Ortofon, Essential III delivers lively, balanced and highly involving sound that will delight every vinyl lover.   Essential III comes in the aesthetic high gloss colors black, red and white.   Specifications:Phono and Ortofon OM10eBelt drive with synchronous motor and silicone belt  Diamond cut aluminum drive pulley  Chassis & platter made of resonance in-sensitive MDF  Integrated DC-powered motor control minimizes motor vibration and guarantees speed stability  Low tolerance platter bearing with stainless steel spindle  8,6” aluminum with sapphire bearings  Ortofon OM10 cartridge pre-mounted  High-quality semi-balanced Connect it E phono interconnect with gold-plated RCA connectors included  Special decoupling feet  Dust cover included  High-gloss colour options: black, red, white  Counterweight for mass : 3 - 5,5g (included)Tracking force range: 0 - 25mn (OM5 18mn recommended)Included accessory: power supply, dust coverPower consumption: 4,5 watts maxDimensions: 420 x 112 x 330mm (WxHxD)Weight: 5,0 kg net

The transparent acrylic plinth stands on three individually height-adjustable TPE-damped aluminium cones and carries the motor and the sub-chassis. The sub-chassis, made of Corian, rests on three magnetic fields. A magnetic subchassis suspension system avoids parasitic noise normally caused by con-ventional spring mechanism.A supplied spirit level allows easy adjustment of the sub-chassis. A quiet running AC motor unit drives the platter's outside edge via a belt. It does incorporate an advanced DC-driven motor control, that ensures perfect speed stability and electronic speed change.  The resonance-optimised platter is a sandwich construction utilising a fine-balanced medium density fibre platter and a 4mm thick flat-ground layer of vinyl and a screw-down metal record clamp. It runs on an inverted bearing with stainless-steel axle carrying a ceramic ball/plate bearing. The headshell and armtube of high-end tonearm 9cc Evolution are fashioned from a single piece of carbon-fibre. A conical armtube avoids standing wave reflections.Features:Acrylic Plinth  Sub-chassis made from Corian with magnetic suspension  Acoustically inert sandwich construction of platter with combination of MDF and vinyl layer as mat  Inverted main bearing with ceramic ball/plate  Belt drive with AC motor with DC driven AC generator  Electronic speed control with 33/45 rpm switching  Pre-mounted 9" tonearm 9 cc Evolution  Tonearm bearings with ABEC 7 ballraces  5P Connect it Phono CC cable with RCA plugs  

This turntable makes use of traditional frame design which was established by the famous turntable manufacturers of the 50's and 60's. It uses a compact simple and elegant form factor. The Classic incorporates a combination of approved belt drive design using a low noise AC motor with an ultra-precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability. Advanced technology is used for decoupling and the completely new designed tone-arm Specifications:Belt drive with manual speed control 33/45 rpmHeight adjustable decoupling feetPrecision balanced TPE*-damped aluminium-platter / felt matMetal/MDF sandwich chassis floating on TPE* suspension9” carbon/aluminium tonearm with MM & MC capabilityJapanese ball bearing (base of tonearm)Integrated central vertical cable outlet for unhindered arm movementUltra low friction Zircon pin-point cardan bearings (top & side)Azimuth and VTA fully adjustableTPE damped counterweightOptionally available with 2M Silver phono cartridgeClassic wooden chassis in 3 matt finishes (walnut, rose nut, eucalyptus)Dustcover included

It’s a new era for DJs! With the PT01 Scratch portable turntable, you can scratch and cut—anywhere. Built with Numark’s exclusive Adjustable Scratch Switch™, PT01 Scratch enables you to grab your favorite scratch record (not included) and perform any turntablist scratch routine, whether you have access to AC wall power or you’re outdoors with your friends. While keeping FRESH with a dope paint job, PT01 Scratch is designed for any DJ that is passionate for the art of turntablism and enjoy digging for vinyl records. Yes! There’s an Adjustable Scratch Switch™ that gives you the perfect way to scratch, plus it’s adjustable for either right-handed or left-handed scratching styles. You can simply unscrew the scratch switch and adjust it to your style. Our scratch and slide switch performs longer than ordinary sliders, plus, unlike others, it’s user-replaceable, so the action never stops! PT01 Scratch comes equipped with a red slip-mat to perform light to heavy-handed scratches with your scratch records. Connect your phone or any audio source to play a background beat through the 1/8” stereo input and scratch along to the beat. Increase the volume with the gain control and play it loud and strong on the built-in speaker. You can also connect PT01 Scratch to other equipment via the RCA stereo outputs or use the headphone output for private listening. In addition to scratching and having fun, you also have the capability to record your vinyl digitally via USB to your laptop (with free downloadable software). PT01 Scratch plugs into a wall outlet (AC wall adapter included) and it also runs on batteries. It’s enclosed in a hard case for protection and has a sleek red handle to carry it anywhere. Features:Built-in adjustable Scratch Slide SwitchUser-replaceable scratch slide-switch keeps the action goingProtective dust cover and integrated carrying handleWall-powered with included AC adapter or six batteries(not included)Built-in speakerCartridge includedRemovable slip-matClass-compliant USB connection for PC recording33 1/3, 45 and 78 RPM settingsRCA line and headphone outputs1/8" Aux input with adjustable volume

A turntable set-up does not need to be complicated like rocket-science, our VTE turntable proves that. This good sounding belt-driven deck offers 2 versions for left– and right-handed users.The VTE turntable can be positioned on a table or mounted on a wall. The fastest installation process is made possible, because it comes pre-adjusted out of the box. No further set-up is needed. Tracking force and anti-skating are carefully set.Features:Vertical standing or wall mount option included  Choose “R” (right-handed) or “L” (left-handed) version  Instant playback with super-easy setup  Record clamp for secure record fixing  Belt drive with silicone belt  Low vibration synchronous motor & DC power supply  8,6” aluminium tonearm  Ortofon OM5e cartridge, pre-mounted  Pre-adjusted tracking force & anti-skating force  Special mechanism for perfect tracking in vertical position  Pre-mounted gold-plated RCA interconnect cable  Specifications:Speed: 33, 45 (manual speed change)Principle: belt driveSpeed variance: 33: 0,8% 45: 0,7%Wow & flutter: 33: 0,29% 45: 0,27%Signal to noise: - 65dBPlatter: 300mm MDF with felt mat (0,8kg)Main bearing: stainless steelEffective arm length: 218,5 mmOverhang: 22,0mmEffective tonearm mass: 8,0grCounterweight for mass: 3 - 5,5g (included)Tracking force range: 0 - 25mN (OM5 18mN pre-adjusted)Included accessory: power supply, record clampPower consumption: 4,5 wattsDimensions (standing on table): 430 x 345 x 245mm (WxHxD)Dimensions (mounted on wall): 430 x 310 x 130mm (WxHxD)Weight: 2,8 kg net 

A turntable set-up does not need to be complicated like rocket-science, our VTE turntable proves that. This good sounding belt-driven deck offers 2 versions for left– and right-handed users.The VTE turntable can be positioned on a table or mounted on a wall. The fastest installation process is made possible, because it comes pre-adjusted out of the box. No further set-up is needed. Tracking force and anti-skating are carefully set.Features:Vertical standing or wall mount option included  Choose “R” (right-handed) or “L” (left-handed) version  Instant playback with super-easy setup  Record clamp for secure record fixing  Belt drive with silicone belt  Low vibration synchronous motor & DC power supply  8,6” aluminium tonearm  Ortofon OM5e cartridge, pre-mounted  Pre-adjusted tracking force & anti-skating force  Special mechanism for perfect tracking in vertical position  Pre-mounted gold-plated RCA interconnect cable  Specifications:Speed: 33, 45 (manual speed change)Principle: belt driveSpeed variance: 33: 0,8% 45: 0,7%Wow & flutter: 33: 0,29% 45: 0,27%Signal to noise: - 65dBPlatter: 300mm MDF with felt mat (0,8kg)Main bearing: stainless steelEffective arm length: 218,5 mmOverhang: 22,0mmEffective tonearm mass: 8,0grCounterweight for mass: 3 - 5,5g (included)Tracking force range: 0 - 25mN (OM5 18mN pre-adjusted)Included accessory: power supply, record clampPower consumption: 4,5 wattsDimensions (standing on table): 430 x 345 x 245mm (WxHxD)Dimensions (mounted on wall): 430 x 310 x 130mm (WxHxD)Weight: 2,8 kg net 

A turntable set-up does not need to be complicated like rocket-science, our VTE turntable proves that. This good sounding belt-driven deck offers 2 versions for left– and right-handed users.The VTE turntable can be positioned on a table or mounted on a wall. The fastest installation process is made possible, because it comes pre-adjusted out of the box. No further set-up is needed. Tracking force and anti-skating are carefully set.Features:Vertical standing or wall mount option included  Choose “R” (right-handed) or “L” (left-handed) version  Instant playback with super-easy setup  Record clamp for secure record fixing  Belt drive with silicone belt  Low vibration synchronous motor & DC power supply  8,6” aluminium tonearm  Ortofon OM5e cartridge, pre-mounted  Pre-adjusted tracking force & anti-skating force  Special mechanism for perfect tracking in vertical position  Pre-mounted gold-plated RCA interconnect cable  Specifications:Speed: 33, 45 (manual speed change)Principle: belt driveSpeed variance: 33: 0,8% 45: 0,7%Wow & flutter: 33: 0,29% 45: 0,27%Signal to noise: - 65dBPlatter: 300mm MDF with felt mat (0,8kg)Main bearing: stainless steelEffective arm length: 218,5 mmOverhang: 22,0mmEffective tonearm mass: 8,0grCounterweight for mass: 3 - 5,5g (included)Tracking force range: 0 - 25mN (OM5 18mN pre-adjusted)Included accessory: power supply, record clampPower consumption: 4,5 wattsDimensions (standing on table): 430 x 345 x 245mm (WxHxD)Dimensions (mounted on wall): 430 x 310 x 130mm (WxHxD)Weight: 2,8 kg net 

A quiet-running synchronous motor with silicone belt is driving a low-resonance platter made from laminated particle board. A new motor control with DC power supply minimzes unwanted vibration effectively. The main platter bearing consists of stainless steelspindle and bronze bushing with Teflon bottom to seccure low friction. The main chassis is made from lightweight, but very stiff particle board.  Essential II Phono USB utilises a straight 8,6“ aluminium tonearm design made from a single piece of aluminium with sapphire bearings, which offers a far better „plug & play“ solution, than it‘s predecessor. Special feet effectively decouples the turntable from the surface.  Because Essential II Phono USB comes with pre-mounted cartridge and built-in phono preamplifier with USB output, connection to both line-level input of your hifi system and PC/Mac easily can be used simultaneously! Open-Source recording software Audacity® is not based on a specific platform, is available for free and the perfect solution for recording and processing of your audio data.  Χαρακτηριστικά:Belt drive with silicone belt  Low vibration synchronous motor  Integrated motor control with DC power supply secures silent running  Main platter bearing made from stainless steel runs in bronze bushing with Teflon bottom  8,6” aluminium tonearm with sapphire bearings  Ortofon OM5e cartridge, pre-mounted  Pre-mounted gold-plated RCA interconnect cable  Built-in MM phono stage  Connections: line-level RCA to amp & USB to PC/Mac (simultaneously)  Special turntable feet for effective decoupling  Colour options: Black, Red, White   

A quiet-running synchronous motor with silicone belt is driving a low-resonance platter made from laminated particle board. A new motor control with DC power supply minimzes unwanted vibration effectively. The main platter bearing consists of stainless steelspindle and bronze bushing with Teflon bottom to seccure low friction. The main chassis is made from lightweight, but very stiff particle board.  Essential II Phono USB utilises a straight 8,6“ aluminium tonearm design made from a single piece of aluminium with sapphire bearings, which offers a far better „plug & play“ solution, than it‘s predecessor. Special feet effectively decouples the turntable from the surface.  Because Essential II Phono USB comes with pre-mounted cartridge and built-in phono preamplifier with USB output, connection to both line-level input of your hifi system and PC/Mac easily can be used simultaneously! Open-Source recording software Audacity® is not based on a specific platform, is available for free and the perfect solution for recording and processing of your audio data.  Χαρακτηριστικά:Belt drive with silicone belt  Low vibration synchronous motor  Integrated motor control with DC power supply secures silent running  Main platter bearing made from stainless steel runs in bronze bushing with Teflon bottom  8,6” aluminium tonearm with sapphire bearings  Ortofon OM5e cartridge, pre-mounted  Pre-mounted gold-plated RCA interconnect cable  Built-in MM phono stage  Connections: line-level RCA to amp & USB to PC/Mac (simultaneously)  Special turntable feet for effective decoupling  Colour options: Black, Red, White   

A quiet-running synchronous motor with silicone belt is driving a low-resonance platter made from laminated particle board. A new motor control with DC power supply minimzes unwanted vibration effectively. The main platter bearing consists of stainless steelspindle and bronze bushing with Teflon bottom to seccure low friction. The main chassis is made from lightweight, but very stiff particle board.  Essential II Phono USB utilises a straight 8,6“ aluminium tonearm design made from a single piece of aluminium with sapphire bearings, which offers a far better „plug & play“ solution, than it‘s predecessor. Special feet effectively decouples the turntable from the surface.  Because Essential II Phono USB comes with pre-mounted cartridge and built-in phono preamplifier with USB output, connection to both line-level input of your hifi system and PC/Mac easily can be used simultaneously! Open-Source recording software Audacity® is not based on a specific platform, is available for free and the perfect solution for recording and processing of your audio data.  Χαρακτηριστικά:Belt drive with silicone belt  Low vibration synchronous motor  Integrated motor control with DC power supply secures silent running  Main platter bearing made from stainless steel runs in bronze bushing with Teflon bottom  8,6” aluminium tonearm with sapphire bearings  Ortofon OM5e cartridge, pre-mounted  Pre-mounted gold-plated RCA interconnect cable  Built-in MM phono stage  Connections: line-level RCA to amp & USB to PC/Mac (simultaneously)  Special turntable feet for effective decoupling  Colour options: Black, Red, White   

Many new audio systems, like home cinema receivers, soundbars, multiroom audio, TVs and Bluetooth speakers only offer digital optic input connections: So up to now vinyl lovers using such systems had no chance to play their records on those systems. The perfect solution is: Essential II DIGITAL An unique belt-drive turntable with built-in MM pre-amplifier that features digital optic as well as analogue amplifier connection options. Delivered with acrylic lid and in white.Features:Ideal for connection to multiroom systems (SONOS, HEOS etc) or TVs, soundbars and portable audio  Perfect solution if only a digital input is available  Easy set-up  Belt drive with silicone belt and low vibration motor  8,6” aluminium tonearm with sapphire bearings  Ortofon OM5e cartridge pre-mounted  Built-in phono pre-amplifier with analogue & digital out  Gold-plated RCA interconnect cable included  Special turntable feet for effective decoupling  Specifications:Speed: 33, 45 (manual speed change)Principle: belt driveSpeed variance: 33: 0,80% 45: 0,70%Wow & flutter: 33: 0,29% 45: 0,27%Platter: 300mm particle board with felt mat (0,8kg)Main bearing: stainless steelEffective arm length: 218,5 mmOverhang: 22,0mmEffective tonearm mass: 8,0grCounterweight for mass: 3 - 5,5g (included) 

Many new audio systems, like home cinema receivers, soundbars, multiroom audio, TVs and Bluetooth speakers only offer digital optic input connections: So up to now vinyl lovers using such systems had no chance to play their records on those systems. The perfect solution is: Essential II DIGITAL An unique belt-drive turntable with built-in MM pre-amplifier that features digital optic as well as analogue amplifier connection options. Delivered with acrylic lid and in black.Features:Ideal for connection to multiroom systems (SONOS, HEOS etc) or TVs, soundbars and portable audio  Perfect solution if only a digital input is available  Easy set-up  Belt drive with silicone belt and low vibration motor  8,6” aluminium tonearm with sapphire bearings  Ortofon OM5e cartridge pre-mounted  Built-in phono pre-amplifier with analogue & digital out  Gold-plated RCA interconnect cable included  Special turntable feet for effective decoupling  Specifications:Speed: 33, 45 (manual speed change)Principle: belt driveSpeed variance: 33: 0,80% 45: 0,70%Wow & flutter: 33: 0,29% 45: 0,27%Platter: 300mm particle board with felt mat (0,8kg)Main bearing: stainless steelEffective arm length: 218,5 mmOverhang: 22,0mmEffective tonearm mass: 8,0grCounterweight for mass: 3 - 5,5g (included) 

Many new audio systems, like home cinema receivers, soundbars, multiroom audio, TVs and Bluetooth speakers only offer digital optic input connections: So up to now vinyl lovers using such systems had no chance to play their records on those systems. The perfect solution is: Essential II DIGITAL An unique belt-drive turntable with built-in MM pre-amplifier that features digital optic as well as analogue amplifier connection options. Delivered with acrylic lid and in red.Features:Ideal for connection to multiroom systems (SONOS, HEOS etc) or TVs, soundbars and portable audio  Perfect solution if only a digital input is available  Easy set-up  Belt drive with silicone belt and low vibration motor  8,6” aluminium tonearm with sapphire bearings  Ortofon OM5e cartridge pre-mounted  Built-in phono pre-amplifier with analogue & digital out  Gold-plated RCA interconnect cable included  Special turntable feet for effective decoupling  Specifications:Speed: 33, 45 (manual speed change)Principle: belt driveSpeed variance: 33: 0,80% 45: 0,70%Wow & flutter: 33: 0,29% 45: 0,27%Platter: 300mm particle board with felt mat (0,8kg)Main bearing: stainless steelEffective arm length: 218,5 mmOverhang: 22,0mmEffective tonearm mass: 8,0grCounterweight for mass: 3 - 5,5g (included) 

NAD C 556 Transcription Turntable/Cartridge ComboVinyl Rules!Many of the world’s most ardent music lovers believe that the 33 1/3 RPM Long Playing vinyl record remains the most musically communicative playback medium. NAD has a long history of producing some of the best value-for-money turntables and phono stages. The PP 2i is a legendary budget phono preamp, while the PP 3i takes the superb performance of the PP 2i and adds a simple way to convert your LPs into CDs using your computer and the internet to automate the ‘CD mastering’ process.While vinyl LPs can be a reference quality source of musical enjoyment, they can also sound terrible if the turntable is less than reference quality. Unlike digital sources with their foolproof error correction circuits, the turntable is like a live performance with no room for error. The same piece of vinyl can sound lush, vibrant and spacious on one turntable, but edgy, lifeless and riddled with ticks and pops on another. The difference is the mechanical precision of every aspect of the turntable.Why Does It Sound So Good?When it comes to the C 556, NAD has spent lavishly on the parts of the turntable that define its performance, and has left off the features that do nothing to improve the sound. The result is a turntable that easily outperforms others at twice the modest asking price of the C 556. The secret to a good sounding turntable is to make a rock solid mechanical connection between the platter and the pickup stylus.Any play or vibration will either add resonant colouration (making the smack of a snare drum sound like a thud) or subtract the fine detail that is the primary benefit of well-played vinyl. To achieve this goal we use special materials and techniques. The three mechanisms that make up a turntable are the platter that supports and spins the record; the tone arm, which allows the stylus to accurately track the record; and the cartridge, which transforms the vibrations in the record groove into the electrical signals that are sent to your preamplifier.The platter of the C 556 uses a special phenolic resin that is pressure cast to create the ideal properties of being both massive and inert. The mass creates a flywheel effect that eliminates small, and very unmusical, speed variations called wow and flutter. The mass also rejects unwanted external vibrations, and combined with the extreme hardness of the phenolic material, suppresses vibrations in the audible range. This massive platter requires a precision low friction bearing to allow smooth and stable revolving motion.A special bronze body with a stainless steel ball bearing provides a point-perfect contact with the hardened steel shaft of the platter assembly. This is the ideal design for minimal friction, and a complete elimination of any play or ‘wobble’. The bearing is firmly connected to the rigid and well-damped base that provides a rigid connection to the tone arm. A precision synchronous clock motor keeps the platter spinning at exactly 33 1/3 RPM and its own vibrations are carefully isolated from the platter by a synthetic rubber belt and from the base by rubber isolation mountings.The tone arm must have the lowest possible mass while still maintaining a rigid, vibration-free connection to the record. To achieve this contradictory goal, the C 556 uses a hand built arm featuring an alloy tube and precision bearings at the gimbal pivot. A simple counter weight balance is combined with a magnetic anti-skate bias control to make for a friction-free pivot that allows the cartridge to operate in an ideal environment.Easy to EnjoyBy delivering the turntable with the cartridge already correctly installed and aligned, we were thinking of the many new vinyl devotees who may be less familiar with the setup requirements of a transcription turntable. Setup and operation could not be simpler—the C 556 comes complete. Just set the tone arm counter weight to the indicated position, then plug ‘n play.Whether you are new to vinyl, simply want to upgrade the sound of your vinyl collection, or even want to transcribe your LPs to digital files for playback on your computer, the NAD C 556 is the perfect choice. It is fully capable of providing the ‘vinyl magic’ that has made the LP the most successful recorded medium of all time. With the C 556, NAD is offering the best performing turntable in its 40-year history.Specifications:pressure-cast phenolic resin platter with felt mat provides excellent speed stability and protects records from scratchesprecision bronze and stainless steel ball bearing for smooth, quiet platter rotationhand-built aluminum alloy tonearm with precision gimbal pivot bearingsincludes pre-mounted Ortofon OM-5E moving magnet cartridgemagnetic anti-skate bias controlthree anti-vibration feethigh-torque synchronous-clock motor decoupled from base for reduced vibration transmission and better soundmanual operation with tonearm lift33-1/3 and 45 rpm speedsfrequency range (with included cartridge): 20-20,000 Hz (±2dB)channel separation (with included cartridge): 22dB at 1kHzattached 41" RCA audio cableweight: 8.8 lbs.17-7/16"W x 4-1/2"H (with dust cover down) x 14-1/4"D 

Luxuriously furnished, fully automatic turntable of high standard with three speeds (33, 45, 78 rpm). A solid heavy wooden console and a heavy platter in sandwich construction delivers outstanding absorbance of vibration and speed accuracy.Tone arm technology:Cardan tone arm with mass tracking force set by a high-precision torsion spring. Detachable, Torsional rigid carbon fiber headshell with 13mm (1/2-inch) fixing-holes. Adjustable tracking force and anti-skating.Chassis technology:Solid wooden chassis, floating sub chassis, heavy sandwich platter with additional damping mass ring for the highest fidelity sound.Drive technology:Belt drive with polished flat belt.  DC motor with electric speed control. Viscosity-damped arm lift. Automatic tone arm top-mounted device. Auto Stop with tone arm return. Playback option for archive records at 78 rpm. Supplied with magnetic OMB 10 cartridge.Specifications:Speed r/min.: 33/45/78Speed a ccuracy in%:  DIN / WRMS: 0,07 / 0,04%Rumble-to-noise ratio: 48 dBRumble-noise ratio: 72 dBCartridge system: OMB 10Frequency Response: 10 Hz - 22kHzDimensions (WxHxD): 440 x 119 x 360 mmWeight: 8,2 kgColour:  walnut-silverPower supply: 12 V DC, 150 mA

Luxuriously furnished, fully automatic turntable of high standard with three speeds (33, 45, 78 rpm). A solid heavy wooden console and a heavy platter in sandwich construction delivers outstanding absorbance of vibration and speed accuracy.Tone arm technology:Cardan tone arm with mass tracking force set by a high-precision torsion spring. Detachable, Torsional rigid carbon fiber headshell with 13mm (1/2-inch) fixing-holes. Adjustable tracking force and anti-skating.Chassis technology:Solid wooden chassis, floating sub chassis, heavy sandwich platter with additional damping mass ring for the highest fidelity sound.Drive technology:Belt drive with polished flat belt.  DC motor with electric speed control. Viscosity-damped arm lift. Automatic tone arm top-mounted device. Auto Stop with tone arm return. Playback option for archive records at 78 rpm. Supplied with magnetic OMB 10 cartridge.Specifications:Speed r/min.: 33/45/78Speed a ccuracy in%:  DIN / WRMS: 0,07 / 0,04%Rumble-to-noise ratio: 48 dBRumble-noise ratio: 72 dBCartridge system: OMB 10Frequency Response: 10 Hz - 22kHzDimensions (WxHxD): 440 x 119 x 360 mmWeight: 8,2 kgColour: Walnut-SilverPower supply: 12 V DC, 150 mA

Luxuriously furnished, fully automatic turntable of high standard with three speeds (33, 45, 78 rpm). A solid heavy wooden console and a heavy platter in sandwich construction delivers outstanding absorbance of vibration and speed accuracy.Tone arm technology:Cardan tone arm with mass tracking force set by a high-precision torsion spring. Detachable, Torsional rigid carbon fiber headshell with 13mm (1/2-inch) fixing-holes. Adjustable tracking force and anti-skating.Chassis technology:Solid wooden chassis, floating sub chassis, heavy sandwich platter with additional damping mass ring for the highest fidelity sound.Drive technology:Belt drive with polished flat belt.  DC motor with electric speed control. Viscosity-damped arm lift. Automatic tone arm top-mounted device. Auto Stop with tone arm return. Playback option for archive records at 78 rpm. Supplied with magnetic OMB 10 cartridge.Specifications:Speed r/min.: 33/45/78Speed a ccuracy in%:  DIN / WRMS: 0,07 / 0,04%Rumble-to-noise ratio: 48 dBRumble-noise ratio: 72 dBCartridge system: OMB 10Frequency Response: 10 Hz - 22kHzDimensions (WxHxD): 440 x 119 x 360 mmWeight: 8,2 kgColour: textured lacquer blackPower supply: 12 V DC, 150 mA

High quality, fully automatic turntable with three speeds (33, 45, 78 rpm). This turntable meets all the criteria. Sophisticated technology, greatest convenience combined with great sound leaves the listener with no unfulfilled wishes.Tone arm technology:Cardan bearing with zero-mass tracking force setting, thanks to precision torsion spring. Detachable headshell with 13mm (1/2-inch) fixing-holes. Adjustable tracking force and anti-skating. Extremely rigid headshell made of carbon fiber.Chassis technology:Solid wooden chassis. Floating sub chassis. Vibration damping aluminium platter with antistatic felt mat.Drive technology:Belt drive with polished flat belt. DC motor with electronic speed control. Viscosity-damped arm lift. Automatic tone arm cue. Auto Stop with tone arm return. Playback option for archive disks with 78 rpm speed. Delivered with OMB 10 cartridge.Specifications:Speed r/min.: 33/45/78Speed a ccuracy in% DIN / WRMS: < -/+ 0,07 / 0,04 % DINRumble-to-noise ratio: 48 dBRumble-noise ratio: 72 dBCartridge system: OMB 10Frequency Response: 20 Hz - 22 kHzDepth sensing capability (300 Hz): 70 µm at 315 HzDimensions (WxHxD): 440 x 119 x 360 mmWeight: 5,43 kgColour: black / silverPower supply: 12V DC, 150 mA

With a machined armboard, dedicated external power supply, Linn tonearm, and a moving coil cartridge, this turntable delivers stunning performance and musicality at a price level between Klimax and Majik.The complete Akurate LP12 turntable comprises:Sondek LP12 turntableKore sub-chassis and armboardLingo power supply and motor control unit for the AC motorAkito tonearmKlyde moving coil cartridgeThe Akurate LP12 is available with a choice of solid wood plinths: Black Ash, Cherry, Oak, Rosenut and Walnut. Linn Akurate LP12 Turntable SpecificationsSpeed Accuracy: 0.03%Platter Tolerance: 1/1,000th inchDimensions (WxHxD): 5.5 x 17.5 inches x 14 inchesWeight: 22 lbs

RPM 3 Carbon utilises evolutionary enhancements to improve the performance of RPM series: A low resonance chassis holds an inverted platter bearing with ceramic ball for further reduced rumble. An outboard 15V AC motor is smoothly driven using an ultra precision AC generator with DC power supply for further enhanced speed stability.  A 10“ S-shaped tonearm tube is made from carbon fibre, aluminium and resin. Using a complex 3-step process with heat treatment and 100bar pressure, arm tube rigidity is strenghtened, internal damping is maximized and resonances are reduced to a minimum. This makes the tonearm also suitable for MC cartridges.Additional features are a magnetic antiskating mechanism and a TPE-damped counterweight. All ingredients add up to a miracle in sound for the price and ultra-stylish look!  Features:Precision belt drive using free-standing synchronous motor  Central mass point optimizes vibrancy behaviour  Ultra precision DC-driven AC generator motor power  Inverted platter bearing with ceramic ball  Platter made from MDF using vinyl mat  10” S-shaped tonearm made from carbon, aluminium, resin utilising special heat and pressure treatments  Magnetic antiskating  Counterweight with TPE damping  Available with or without Ortofon 2M Silver cartridge  3 high-gloss colours (black, red, white)  Lid available as an option  ​Specifications:Speed: 33, 45 (manual speed change)Drive principle    belt drivePlatter: 300mm MDFMains bearing:    stainless steel axle with ceramic ballWow & flutter: 33: +/- 0,14% I 45: +/- 0,11%Speed drift: 33: +/- 0,19% I 45: +/- 0,08%Signal to noise    - 71dBTonearm    10” carbon, aluminium and resinEffective arm length: 254 mmEffective arm mass: 16 gOverhang: 16mmTracking force:    0 - 25mNPower supply: 15 volts DC / 800 mA power supply110/240 Volt - 50 or 60 HzPower consumption: 5 watt max / < 0,5 watt standbyDimensions: 422 x 118 x 373mm (WxHxD)Weight: 5,5 kg net​

RPM 3 Carbon utilises evolutionary enhancements to improve the performance of RPM series: A low resonance chassis holds an inverted platter bearing with ceramic ball for further reduced rumble. An outboard 15V AC motor is smoothly driven using an ultra precision AC generator with DC power supply for further enhanced speed stability.  A 10“ S-shaped tonearm tube is made from carbon fibre, aluminium and resin. Using a complex 3-step process with heat treatment and 100bar pressure, arm tube rigidity is strenghtened, internal damping is maximized and resonances are reduced to a minimum. This makes the tonearm also suitable for MC cartridges.Additional features are a magnetic antiskating mechanism and a TPE-damped counterweight. All ingredients add up to a miracle in sound for the price and ultra-stylish look!  Features:Precision belt drive using free-standing synchronous motor  Central mass point optimizes vibrancy behaviour  Ultra precision DC-driven AC generator motor power  Inverted platter bearing with ceramic ball  Platter made from MDF using vinyl mat  10” S-shaped tonearm made from carbon, aluminium, resin utilising special heat and pressure treatments  Magnetic antiskating  Counterweight with TPE damping  Available with or without Ortofon 2M Silver cartridge  3 high-gloss colours (black, red, white)  Lid available as an option  ​Specifications:Speed: 33, 45 (manual speed change)Drive principle    belt drivePlatter: 300mm MDFMains bearing:    stainless steel axle with ceramic ballWow & flutter: 33: +/- 0,14% I 45: +/- 0,11%Speed drift: 33: +/- 0,19% I 45: +/- 0,08%Signal to noise    - 71dBTonearm    10” carbon, aluminium and resinEffective arm length: 254 mmEffective arm mass: 16 gOverhang: 16mmTracking force:    0 - 25mNPower supply: 15 volts DC / 800 mA power supply110/240 Volt - 50 or 60 HzPower consumption: 5 watt max / < 0,5 watt standbyDimensions: 422 x 118 x 373mm (WxHxD)Weight: 5,5 kg net​

RPM 3 Carbon utilises evolutionary enhancements to improve the performance of RPM series: A low resonance chassis holds an inverted platter bearing with ceramic ball for further reduced rumble. An outboard 15V AC motor is smoothly driven using an ultra precision AC generator with DC power supply for further enhanced speed stability.  A 10“ S-shaped tonearm tube is made from carbon fibre, aluminium and resin. Using a complex 3-step process with heat treatment and 100bar pressure, arm tube rigidity is strenghtened, internal damping is maximized and resonances are reduced to a minimum. This makes the tonearm also suitable for MC cartridges.Additional features are a magnetic antiskating mechanism and a TPE-damped counterweight. All ingredients add up to a miracle in sound for the price and ultra-stylish look!  Features:Precision belt drive using free-standing synchronous motor  Central mass point optimizes vibrancy behaviour  Ultra precision DC-driven AC generator motor power  Inverted platter bearing with ceramic ball  Platter made from MDF using vinyl mat  10” S-shaped tonearm made from carbon, aluminium, resin utilising special heat and pressure treatments  Magnetic antiskating  Counterweight with TPE damping  Available with or without Ortofon 2M Silver cartridge  3 high-gloss colours (black, red, white)  Lid available as an option  ​Specifications:Speed: 33, 45 (manual speed change)Drive principle    belt drivePlatter: 300mm MDFMains bearing:    stainless steel axle with ceramic ballWow & flutter: 33: +/- 0,14% I 45: +/- 0,11%Speed drift: 33: +/- 0,19% I 45: +/- 0,08%Signal to noise    - 71dBTonearm    10” carbon, aluminium and resinEffective arm length: 254 mmEffective arm mass: 16 gOverhang: 16mmTracking force:    0 - 25mNPower supply: 15 volts DC / 800 mA power supply110/240 Volt - 50 or 60 HzPower consumption: 5 watt max / < 0,5 watt standbyDimensions: 422 x 118 x 373mm (WxHxD)Weight: 5,5 kg net​

RPM 3 Carbon utilises evolutionary enhancements to improve the performance of RPM series: A low resonance chassis holds an inverted platter bearing with ceramic ball for further reduced rumble. An outboard 15V AC motor is smoothly driven using an ultra precision AC generator with DC power supply for further enhanced speed stability.  A 10“ S-shaped tonearm tube is made from carbon fibre, aluminium and resin. Using a complex 3-step process with heat treatment and 100bar pressure, arm tube rigidity is strenghtened, internal damping is maximized and resonances are reduced to a minimum. This makes the tonearm also suitable for MC cartridges.Additional features are a magnetic antiskating mechanism and a TPE-damped counterweight. All ingredients add up to a miracle in sound for the price and ultra-stylish look!  Features:Precision belt drive using free-standing synchronous motor  Central mass point optimizes vibrancy behaviour  Ultra precision DC-driven AC generator motor power  Inverted platter bearing with ceramic ball  Platter made from MDF using vinyl mat  10” S-shaped tonearm made from carbon, aluminium, resin utilising special heat and pressure treatments  Magnetic antiskating  Counterweight with TPE damping  Available with or without Ortofon 2M Silver cartridge  3 high-gloss colours (black, red, white)  Lid available as an option  ​Specifications:Speed: 33, 45 (manual speed change)Drive principle    belt drivePlatter: 300mm MDFMains bearing:    stainless steel axle with ceramic ballWow & flutter: 33: +/- 0,14% I 45: +/- 0,11%Speed drift: 33: +/- 0,19% I 45: +/- 0,08%Signal to noise    - 71dBTonearm    10” carbon, aluminium and resinEffective arm length: 254 mmEffective arm mass: 16 gOverhang: 16mmTracking force:    0 - 25mNPower supply: 15 volts DC / 800 mA power supply110/240 Volt - 50 or 60 HzPower consumption: 5 watt max / < 0,5 watt standbyDimensions: 422 x 118 x 373mm (WxHxD)Weight: 5,5 kg net​

RPM 3 Carbon utilises evolutionary enhancements to improve the performance of RPM series: A low resonance chassis holds an inverted platter bearing with ceramic ball for further reduced rumble. An outboard 15V AC motor is smoothly driven using an ultra precision AC generator with DC power supply for further enhanced speed stability.  A 10“ S-shaped tonearm tube is made from carbon fibre, aluminium and resin. Using a complex 3-step process with heat treatment and 100bar pressure, arm tube rigidity is strenghtened, internal damping is maximized and resonances are reduced to a minimum. This makes the tonearm also suitable for MC cartridges.Additional features are a magnetic antiskating mechanism and a TPE-damped counterweight. All ingredients add up to a miracle in sound for the price and ultra-stylish look!  Features:Precision belt drive using free-standing synchronous motor  Central mass point optimizes vibrancy behaviour  Ultra precision DC-driven AC generator motor power  Inverted platter bearing with ceramic ball  Platter made from MDF using vinyl mat  10” S-shaped tonearm made from carbon, aluminium, resin utilising special heat and pressure treatments  Magnetic antiskating  Counterweight with TPE damping  Available with or without Ortofon 2M Silver cartridge  3 high-gloss colours (black, red, white)  Lid available as an option  ​Specifications:Speed: 33, 45 (manual speed change)Drive principle    belt drivePlatter: 300mm MDFMains bearing:    stainless steel axle with ceramic ballWow & flutter: 33: +/- 0,14% I 45: +/- 0,11%Speed drift: 33: +/- 0,19% I 45: +/- 0,08%Signal to noise    - 71dBTonearm    10” carbon, aluminium and resinEffective arm length: 254 mmEffective arm mass: 16 gOverhang: 16mmTracking force:    0 - 25mNPower supply: 15 volts DC / 800 mA power supply110/240 Volt - 50 or 60 HzPower consumption: 5 watt max / < 0,5 watt standbyDimensions: 422 x 118 x 373mm (WxHxD)Weight: 5,5 kg net​

RPM 5 Carbon utilises a radical concept with a lot of innovations, that originate from its big brother RPM 9 Carbon: A low resonance chassis holds a newly designed inverted platter bearing with ceramic ball for further reduced rumble.The acoustically inert platter is made from acrylic. An outboard 15V AC motor is smoothly driven using an ultra-precision AC generator with DC power supply for further enhanced speed stability. The classy 9“ cc Evo tonearm, which is made from carbon fibre is suitable for any high-quality MM or MC cartridge.A TPE-damped counterweight eliminates unwanted resonances. All ingredients add up to a miracle in sound for the price. Its ultra-stylish look is available in 3 exclusive high-gloss finish versions.  Features:Precision belt drive principle using synchronous motor  Ultra-precision DC-driven AC generator motor power  Inverted platter bearing with ceramic ball  Acoustical inert acrylic platter  9” cc EVO tonearm made from carbon  Counterweight with TPE damping  Adjustable aluminium tip-toe feet  Available with or without Ortofon Quintet red cartridge  3 high-gloss colours (black, red, white)  Lid available as an option  ​Specifications:Speed: 33, 45 (manual speed change)Drive principle    belt drivePlatter: 300mm acrylicMains bearing: stainless steel axle with ceramic ballWow & flutter: 33: +/- 0,12% I 45: +/- 0,10%Speed drift: 33: +/- 0,17% I 45: +/- 0,08%Signal to noise    - 73dBTonearm    9” cc EVO carbonEffective arm length: 230 mmEffective arm mass: 8 gOverhang: 18mmTracking force: 0 - 25mNPower supply: 15 volts DC / 800 mA power supply110/240 Volt - 50 or 60 HzPower consumption:5 watt max / < 0,3 watt standbyDimensions: 430 x 150 x 323 mm (WxHxD)Weight: 8,0 kg net

RPM 5 Carbon utilises a radical concept with a lot of innovations, that originate from its big brother RPM 9 Carbon: A low resonance chassis holds a newly designed inverted platter bearing with ceramic ball for further reduced rumble.The acoustically inert platter is made from acrylic. An outboard 15V AC motor is smoothly driven using an ultra-precision AC generator with DC power supply for further enhanced speed stability. The classy 9“ cc Evo tonearm, which is made from carbon fibre is suitable for any high-quality MM or MC cartridge.A TPE-damped counterweight eliminates unwanted resonances. All ingredients add up to a miracle in sound for the price. Its ultra-stylish look is available in 3 exclusive high-gloss finish versions.  Features:Precision belt drive principle using synchronous motor  Ultra-precision DC-driven AC generator motor power  Inverted platter bearing with ceramic ball  Acoustical inert acrylic platter  9” cc EVO tonearm made from carbon  Counterweight with TPE damping  Adjustable aluminium tip-toe feet  Available with or without Ortofon Quintet red cartridge  3 high-gloss colours (black, red, white)  Lid available as an option  ​Specifications:Speed: 33, 45 (manual speed change)Drive principle    belt drivePlatter: 300mm acrylicMains bearing: stainless steel axle with ceramic ballWow & flutter: 33: +/- 0,12% I 45: +/- 0,10%Speed drift: 33: +/- 0,17% I 45: +/- 0,08%Signal to noise    - 73dBTonearm    9” cc EVO carbonEffective arm length: 230 mmEffective arm mass: 8 gOverhang: 18mmTracking force: 0 - 25mNPower supply: 15 volts DC / 800 mA power supply110/240 Volt - 50 or 60 HzPower consumption:5 watt max / < 0,3 watt standbyDimensions: 430 x 150 x 323 mm (WxHxD)Weight: 8,0 kg net

RPM 5 Carbon utilises a radical concept with a lot of innovations, that originate from its big brother RPM 9 Carbon: A low resonance chassis holds a newly designed inverted platter bearing with ceramic ball for further reduced rumble.The acoustically inert platter is made from acrylic. An outboard 15V AC motor is smoothly driven using an ultra-precision AC generator with DC power supply for further enhanced speed stability. The classy 9“ cc Evo tonearm, which is made from carbon fibre is suitable for any high-quality MM or MC cartridge.A TPE-damped counterweight eliminates unwanted resonances. All ingredients add up to a miracle in sound for the price. Its ultra-stylish look is available in 3 exclusive high-gloss finish versions.  Features:Precision belt drive principle using synchronous motor  Ultra-precision DC-driven AC generator motor power  Inverted platter bearing with ceramic ball  Acoustical inert acrylic platter  9” cc EVO tonearm made from carbon  Counterweight with TPE damping  Adjustable aluminium tip-toe feet  Available with or without Ortofon Quintet red cartridge  3 high-gloss colours (black, red, white)  Lid available as an option  ​Specifications:Speed: 33, 45 (manual speed change)Drive principle    belt drivePlatter: 300mm acrylicMains bearing: stainless steel axle with ceramic ballWow & flutter: 33: +/- 0,12% I 45: +/- 0,10%Speed drift: 33: +/- 0,17% I 45: +/- 0,08%Signal to noise    - 73dBTonearm    9” cc EVO carbonEffective arm length: 230 mmEffective arm mass: 8 gOverhang: 18mmTracking force: 0 - 25mNPower supply: 15 volts DC / 800 mA power supply110/240 Volt - 50 or 60 HzPower consumption:5 watt max / < 0,3 watt standbyDimensions: 430 x 150 x 323 mm (WxHxD)Weight: 8,0 kg net

Musical Fidelity’s latest interesting product is the Round Table. This is a high quality competitively priced complete turntable solution. It has a high quality low resonance 9” pickup arm (magnetic anti-skating) with steel tipped bearings housed in zirconium with rubber damping, not dissimilar in principle to the Incabloc shock protection system on watches. The vertical bearings are ABEC7 ball bearings. It is fitted with an Audio Technica 95E cartridge.Musical Fidelity has a long heritage of designing exceptional turntables and the Round Table is no exception: Produced to Musical Fidelity&#39;s bespoke specification, the new turntable also includes a unique feature.Much effort has be made to ensure that, for the first time, all of the decks components have been designed and placed to guarantee that the product is perfectly, statically balanced and that its centre of gravity is at the pivot point of the main bearing.Other top spec components include: a polished high carbon tool steel bearing – for an exceptional long life and friction free performance – an extremely inert chassis and suspension system and a very high quality pick up arm, usually used on products several price categories higher. Specifications:Nominal speed 33/45 rpm, outside belt drive system, manual speed changeSpeed Variance 33rpm: ± 0.30 %, 45rpm: ± 0.20 %Wow and flutter 33rpm: ± 0.10%, 45rpm: ± 0.09%Signal to noise ratio Mechanical noise: - 39 dBElectrical noise: -65dBDownforce range 0 - 25 mNTonearm 9&#39;&#39; straight shape massive aluminium constructionSupplied counterweights no. 82, weight 114g (± 1g), for cartridges from 5 to 13gEffective tonearm mass 14gEffective tonearm length 230mm (tonearm mounting distance 212mm)Overhang 18mmPower requirement 15V 0.8A (Adaptor supplied)Consumption >0.25 Watts standby 5 Watts maximumAdaptor mains voltage 90-264 VAC 47-63HzUnit only, unboxed 6 kg (131/5 lbs)In shipping carton 8 kg (173/5 lbs)

Musical Fidelity’s latest interesting product is the Round Table. This is a high quality competitively priced complete turntable solution. It has a high quality low resonance 9” pickup arm (magnetic anti-skating) with steel tipped bearings housed in zirconium with rubber damping, not dissimilar in principle to the Incabloc shock protection system on watches. The vertical bearings are ABEC7 ball bearings. It is fitted with an Audio Technica 95E cartridge.Musical Fidelity has a long heritage of designing exceptional turntables and the Round Table is no exception: Produced to Musical Fidelity's bespoke specification, the new turntable also includes a unique feature.Much effort has be made to ensure that, for the first time, all of the decks components have been designed and placed to guarantee that the product is perfectly, statically balanced and that its centre of gravity is at the pivot point of the main bearing.Other top spec components include: a polished high carbon tool steel bearing – for an exceptional long life and friction free performance – an extremely inert chassis and suspension system and a very high quality pick up arm, usually used on products several price categories higher. Specifications:Nominal speed 33/45 rpm, outside belt drive system, manual speed changeSpeed Variance 33rpm: ± 0.30 %, 45rpm: ± 0.20 %Wow and flutter 33rpm: ± 0.10%, 45rpm: ± 0.09%Signal to noise ratio Mechanical noise: - 39 dBElectrical noise: -65dBDownforce range 0 - 25 mNTonearm 9'' straight shape massive aluminium constructionSupplied counterweights no. 82, weight 114g (± 1g), for cartridges from 5 to 13gEffective tonearm mass 14gEffective tonearm length 230mm (tonearm mounting distance 212mm)Overhang 18mmPower requirement 15V 0.8A (Adaptor supplied)Consumption >0.25 Watts standby 5 Watts maximumAdaptor mains voltage 90-264 VAC 47-63HzUnit only, unboxed 6 kg (131/5 lbs)In shipping carton 8 kg (173/5 lbs)

The latest edition to the RPM range of turntables follows on from where the hugely popular Genie 3 left off. Utilising a range of innovative improvements over its predecessor, the RPM-1 Carbon stands out from the crowd with its stunning design, impeccable sound and affordable price.The new RPM-1 Carbon design has been upgraded to significantly reduce resonance across the turntable. While maintaining the instantly recognisable shape, this turntable boasts improvements in the tonearm, bearing, and motor.The brand new tonearm is a carbon fibre/aluminium resin construct, made using special heat and pressure treatments. The result of this new design is a tonearm that is more solid and anti-resonant than ever before at this price, while maintaining a light weight. The arm is finished off with a pre-fitted Ortofon 2m Red cartridge and a new magnetic anti-skate mechanism. The improved counterweight also utilises TPE damping in the form of an anti-resonant ring around the fixing point.The completely decoupled motor is based upon the same design as the Xpression Carbon, powered by an AC generator that's connected to the new  DC power supply. The inverted main bearing now utilises a ceramic ball, offering a more fluid and consistent platter rotation than ever before.Features:With Ortofon 2M RedPrecision belt drive using synchronous motorUltra-precision DC-driven AC generator motor powerInverted platter bearing with ceramic ballPlatter made from MDF using felt mat8,6” S-shaped tonearm made from carbon, aluminium, resin utilising special heat and pressure treatmentsMagnetic anti-skatingCounterweight with TPE dampingPre-fitted Ortofon 2M Red cartridge3 high-gloss colours (black, red, white)Lid available as optional extraSpecifications:Speed : 33, 45 (manual speed change)Drive principle : belt drivePlatter : 300mm MDFMains bearing : stainless steel axle with ceramic ballWow & flutter : 33: +/- 0,14% I 45: +/- 0,13%Speed drift : 33: +/- 0,27% I 45: +/- 0,19%Signal to noise : - 71dBTonearm : 8,6” carbon; aluminium and resinEffective arm length : 218,5 mmEffective arm mass : 13,5 gOverhang : 22mmTracking force : 0 - 25mNIncluded accessories : 15 volts DC / 500 mA power supplyPower connection : 110/240 Volt - 50 or 60 HzPower consumption : 5 watt max / < 0,5 watt standbyDimensions : 380 x 110 x 350mm (WxHxD)Weight : 3,8 kg net

The latest edition to the RPM range of turntables follows on from where the hugely popular Genie 3 left off. Utilising a range of innovative improvements over its predecessor, the RPM-1 Carbon stands out from the crowd with its stunning design, impeccable sound and affordable price.The new RPM-1 Carbon design has been upgraded to significantly reduce resonance across the turntable. While maintaining the instantly recognisable shape, this turntable boasts improvements in the tonearm, bearing, and motor.The brand new tonearm is a carbon fibre/aluminium resin construct, made using special heat and pressure treatments. The result of this new design is a tonearm that is more solid and anti-resonant than ever before at this price, while maintaining a light weight. The arm is finished off with a pre-fitted Ortofon 2m Red cartridge and a new magnetic anti-skate mechanism. The improved counterweight also utilises TPE damping in the form of an anti-resonant ring around the fixing point.The completely decoupled motor is based upon the same design as the Xpression Carbon, powered by an AC generator that's connected to the new  DC power supply. The inverted main bearing now utilises a ceramic ball, offering a more fluid and consistent platter rotation than ever before.Features:With Ortofon 2M RedPrecision belt drive using synchronous motorUltra-precision DC-driven AC generator motor powerInverted platter bearing with ceramic ballPlatter made from MDF using felt mat8,6” S-shaped tonearm made from carbon, aluminium, resin utilising special heat and pressure treatmentsMagnetic anti-skatingCounterweight with TPE dampingPre-fitted Ortofon 2M Red cartridge3 high-gloss colours (black, red, white)Lid available as optional extraSpecifications:Speed : 33, 45 (manual speed change)Drive principle : belt drivePlatter : 300mm MDFMains bearing : stainless steel axle with ceramic ballWow & flutter : 33: +/- 0,14% I 45: +/- 0,13%Speed drift : 33: +/- 0,27% I 45: +/- 0,19%Signal to noise : - 71dBTonearm : 8,6” carbon; aluminium and resinEffective arm length : 218,5 mmEffective arm mass : 13,5 gOverhang : 22mmTracking force : 0 - 25mNIncluded accessories : 15 volts DC / 500 mA power supplyPower connection : 110/240 Volt - 50 or 60 HzPower consumption : 5 watt max / < 0,5 watt standbyDimensions : 380 x 110 x 350mm (WxHxD)Weight : 3,8 kg net

The latest edition to the RPM range of turntables follows on from where the hugely popular Genie 3 left off. Utilising a range of innovative improvements over its predecessor, the RPM-1 Carbon stands out from the crowd with its stunning design, impeccable sound and affordable price.The new RPM-1 Carbon design has been upgraded to significantly reduce resonance across the turntable. While maintaining the instantly recognisable shape, this turntable boasts improvements in the tonearm, bearing, and motor.The brand new tonearm is a carbon fibre/aluminium resin construct, made using special heat and pressure treatments. The result of this new design is a tonearm that is more solid and anti-resonant than ever before at this price, while maintaining a light weight. The arm is finished off with a pre-fitted Ortofon 2m Red cartridge and a new magnetic anti-skate mechanism. The improved counterweight also utilises TPE damping in the form of an anti-resonant ring around the fixing point.The completely decoupled motor is based upon the same design as the Xpression Carbon, powered by an AC generator that's connected to the new  DC power supply. The inverted main bearing now utilises a ceramic ball, offering a more fluid and consistent platter rotation than ever before.Features:With Ortofon 2M RedPrecision belt drive using synchronous motorUltra-precision DC-driven AC generator motor powerInverted platter bearing with ceramic ballPlatter made from MDF using felt mat8,6” S-shaped tonearm made from carbon, aluminium, resin utilising special heat and pressure treatmentsMagnetic anti-skatingCounterweight with TPE dampingPre-fitted Ortofon 2M Red cartridge3 high-gloss colours (black, red, white)Lid available as optional extraSpecifications:Speed : 33, 45 (manual speed change)Drive principle : belt drivePlatter : 300mm MDFMains bearing : stainless steel axle with ceramic ballWow & flutter : 33: +/- 0,14% I 45: +/- 0,13%Speed drift : 33: +/- 0,27% I 45: +/- 0,19%Signal to noise : - 71dBTonearm : 8,6” carbon; aluminium and resinEffective arm length : 218,5 mmEffective arm mass : 13,5 gOverhang : 22mmTracking force : 0 - 25mNIncluded accessories : 15 volts DC / 500 mA power supplyPower connection : 110/240 Volt - 50 or 60 HzPower consumption : 5 watt max / < 0,5 watt standbyDimensions : 380 x 110 x 350mm (WxHxD)Weight : 3,8 kg net

The first Debut turntable, introduced in the late 1990s, was a revolution for the hi-fi industry. For the first time after the arrival of Compact Disc and the assumed demise of vinyl records, an analogue product re-emerged in the “mass market” – something all music lovers could afford.  The new DEBUT Carbon DC has been designed to set new standards in this category for the coming decade – perfectly timed as analogue today is again a respected source, while the demand for good turntables is growing again!  The most obvious improvement is the inclusion of a CARBON TUBE for the tonearm, which increases stiffness and decreases unwanted resonance.  This material normally is extensively used in high-end tonearms, but – because of cost reasons – was never used in products at lower price levels. Together with other improvements like an increase in platter size and weight to realize even smoother rotation, the overall sound quality is greatly improved. The approved belt drive design offers low noise AC motor with effective motor decoupling (utilising TPE-damping) and ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability without unwanted vibration.  The DEBUT CARBON DC will be offered in high-gloss black or shiny red, green, blue, yellow, silver or white as no-added-cost option. Specifications: 8,6” carbon tonearm   Increased platter size with more weight   Precision belt drive with synchronous motor   New DC power supply with ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability.   New TPE motor suspension   Felt mat   magnetic cartridge options from Ortofon OM 10 or 2M red   7 high-gloss colours

The first Debut turntable, introduced in the late 1990s, was a revolution for the hi-fi industry. For the first time after the arrival of Compact Disc and the assumed demise of vinyl records, an analogue product re-emerged in the “mass market” – something all music lovers could afford.  The new DEBUT Carbon DC has been designed to set new standards in this category for the coming decade – perfectly timed as analogue today is again a respected source, while the demand for good turntables is growing again!  The most obvious improvement is the inclusion of a CARBON TUBE for the tonearm, which increases stiffness and decreases unwanted resonance.  This material normally is extensively used in high-end tonearms, but – because of cost reasons – was never used in products at lower price levels. Together with other improvements like an increase in platter size and weight to realize even smoother rotation, the overall sound quality is greatly improved. The approved belt drive design offers low noise AC motor with effective motor decoupling (utilising TPE-damping) and ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability without unwanted vibration.  The DEBUT CARBON DC will be offered in high-gloss black or shiny red, green, blue, yellow, silver or white as no-added-cost option. Specifications: 8,6” carbon tonearm   Increased platter size with more weight   Precision belt drive with synchronous motor   New DC power supply with ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability.   New TPE motor suspension   Felt mat   magnetic cartridge options from Ortofon OM 10 or 2M red   7 high-gloss colours

The first Debut turntable, introduced in the late 1990s, was a revolution for the hi-fi industry. For the first time after the arrival of Compact Disc and the assumed demise of vinyl records, an analogue product re-emerged in the “mass market” – something all music lovers could afford.  The new DEBUT Carbon DC has been designed to set new standards in this category for the coming decade – perfectly timed as analogue today is again a respected source, while the demand for good turntables is growing again!  The most obvious improvement is the inclusion of a CARBON TUBE for the tonearm, which increases stiffness and decreases unwanted resonance.  This material normally is extensively used in high-end tonearms, but – because of cost reasons – was never used in products at lower price levels. Together with other improvements like an increase in platter size and weight to realize even smoother rotation, the overall sound quality is greatly improved. The approved belt drive design offers low noise AC motor with effective motor decoupling (utilising TPE-damping) and ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability without unwanted vibration.  The DEBUT CARBON DC will be offered in high-gloss black or shiny red, green, blue, yellow, silver or white as no-added-cost option. Specifications: 8,6” carbon tonearm   Increased platter size with more weight   Precision belt drive with synchronous motor   New DC power supply with ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability.   New TPE motor suspension   Felt mat   magnetic cartridge options from Ortofon OM 10 or 2M red   7 high-gloss colours

The first Debut turntable, introduced in the late 1990s, was a revolution for the hi-fi industry. For the first time after the arrival of Compact Disc and the assumed demise of vinyl records, an analogue product re-emerged in the “mass market” – something all music lovers could afford.  The new DEBUT Carbon DC has been designed to set new standards in this category for the coming decade – perfectly timed as analogue today is again a respected source, while the demand for good turntables is growing again!  The most obvious improvement is the inclusion of a CARBON TUBE for the tonearm, which increases stiffness and decreases unwanted resonance.  This material normally is extensively used in high-end tonearms, but – because of cost reasons – was never used in products at lower price levels. Together with other improvements like an increase in platter size and weight to realize even smoother rotation, the overall sound quality is greatly improved. The approved belt drive design offers low noise AC motor with effective motor decoupling (utilising TPE-damping) and ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability without unwanted vibration.  The DEBUT CARBON DC will be offered in high-gloss black or shiny red, green, blue, yellow, silver or white as no-added-cost option. Specifications: 8,6” carbon tonearm   Increased platter size with more weight   Precision belt drive with synchronous motor   New DC power supply with ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability.   New TPE motor suspension   Felt mat   magnetic cartridge options from Ortofon OM 10 or 2M red   7 high-gloss colours

The first Debut turntable, introduced in the late 1990s, was a revolution for the hi-fi industry. For the first time after the arrival of Compact Disc and the assumed demise of vinyl records, an analogue product re-emerged in the “mass market” – something all music lovers could afford.  The new DEBUT Carbon DC has been designed to set new standards in this category for the coming decade – perfectly timed as analogue today is again a respected source, while the demand for good turntables is growing again!  The most obvious improvement is the inclusion of a CARBON TUBE for the tonearm, which increases stiffness and decreases unwanted resonance.  This material normally is extensively used in high-end tonearms, but – because of cost reasons – was never used in products at lower price levels. Together with other improvements like an increase in platter size and weight to realize even smoother rotation, the overall sound quality is greatly improved. The approved belt drive design offers low noise AC motor with effective motor decoupling (utilising TPE-damping) and ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability without unwanted vibration.  The DEBUT CARBON DC will be offered in high-gloss black or shiny red, green, blue, yellow, silver or white as no-added-cost option. Specifications: 8,6” carbon tonearm   Increased platter size with more weight   Precision belt drive with synchronous motor   New DC power supply with ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability.   New TPE motor suspension   Felt mat   magnetic cartridge options from Ortofon OM 10 or 2M red   7 high-gloss colours

The first Debut turntable, introduced in the late 1990s, was a revolution for the hi-fi industry. For the first time after the arrival of Compact Disc and the assumed demise of vinyl records, an analogue product re-emerged in the “mass market” – something all music lovers could afford.  The new DEBUT Carbon DC has been designed to set new standards in this category for the coming decade – perfectly timed as analogue today is again a respected source, while the demand for good turntables is growing again!  The most obvious improvement is the inclusion of a CARBON TUBE for the tonearm, which increases stiffness and decreases unwanted resonance.  This material normally is extensively used in high-end tonearms, but – because of cost reasons – was never used in products at lower price levels. Together with other improvements like an increase in platter size and weight to realize even smoother rotation, the overall sound quality is greatly improved. The approved belt drive design offers low noise AC motor with effective motor decoupling (utilising TPE-damping) and ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability without unwanted vibration.  The DEBUT CARBON DC will be offered in high-gloss black or shiny red, green, blue, yellow, silver or white as no-added-cost option. Specifications: 8,6” carbon tonearm   Increased platter size with more weight   Precision belt drive with synchronous motor   New DC power supply with ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability.   New TPE motor suspension   Felt mat   magnetic cartridge options from Ortofon OM 10 or 2M red   7 high-gloss colours

The first Debut turntable, introduced in the late 1990s, was a revolution for the hi-fi industry. For the first time after the arrival of Compact Disc and the assumed demise of vinyl records, an analogue product re-emerged in the “mass market” – something all music lovers could afford.  The new DEBUT Carbon DC has been designed to set new standards in this category for the coming decade – perfectly timed as analogue today is again a respected source, while the demand for good turntables is growing again!  The most obvious improvement is the inclusion of a CARBON TUBE for the tonearm, which increases stiffness and decreases unwanted resonance.  This material normally is extensively used in high-end tonearms, but – because of cost reasons – was never used in products at lower price levels. Together with other improvements like an increase in platter size and weight to realize even smoother rotation, the overall sound quality is greatly improved. The approved belt drive design offers low noise AC motor with effective motor decoupling (utilising TPE-damping) and ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability without unwanted vibration.  The DEBUT CARBON DC will be offered in high-gloss black or shiny red, green, blue, yellow, silver or white as no-added-cost option. Specifications: 8,6” carbon tonearm   Increased platter size with more weight   Precision belt drive with synchronous motor   New DC power supply with ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability.   New TPE motor suspension   Felt mat   magnetic cartridge options from Ortofon OM 10 or 2M red   7 high-gloss colours ​​

The first Debut turntable, introduced in the late 1990s, was a revolution for the hi-fi industry. For the first time after the arrival of Compact Disc and the assumed demise of vinyl records, an analogue product re-emerged in the “mass market” – something all music lovers could afford.  The new DEBUT Carbon DC has been designed to set new standards in this category for the coming decade – perfectly timed as analogue today is again a respected source, while the demand for good turntables is growing again!  The most obvious improvement is the inclusion of a CARBON TUBE for the tonearm, which increases stiffness and decreases unwanted resonance.  This material normally is extensively used in high-end tonearms, but – because of cost reasons – was never used in products at lower price levels. Together with other improvements like an increase in platter size and weight to realize even smoother rotation, the overall sound quality is greatly improved. The approved belt drive design offers low noise AC motor with effective motor decoupling (utilising TPE-damping) and ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability without unwanted vibration.  The DEBUT CARBON DC will be offered in high-gloss black or shiny red, green, blue, yellow, silver or white as no-added-cost option. Specifications: 8,6” carbon tonearm   Increased platter size with more weight   Precision belt drive with synchronous motor   New DC power supply with ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability.   New TPE motor suspension   Felt mat   magnetic cartridge options from Ortofon OM 10 or 2M red   7 high-gloss colours