Προενισχυτές Phono

The LX2-LPS is Musical Fidelity's new baby. A high quality flexible MM/MC phono stage with adjustable impedance and excellent technical performance. Housed in beautifully detailed and handsome metalwork it is the epitome of understated high class elegance.We designed it for reference level listening so it is unerringly accurate and faithful to the input. Its purpose in life is to give you your music as its artists and producers intended: nothing more, and nothing less. The critical elements of a phono stage are: accurate RIAA, low noise, low distortion, and overload margin. Technical PerformanceMusical Fidelity's RIAA correction is famous for its predictable and consistent accuracy. The LX2-LPS accuracy is ±0.25dB 20Hz-20kHZ, also it extends to 45kHz so there is no overshoot ringing.This results in absolutely clear high frequencies with no intermodulation or other distracting anomalies.The noise ratio on both MM (better than 82dB) and MC (better than 72dB) is outstanding and virtually inaudible at any volume setting. That is unless you are a half deaf head-banger.But then I don't expect that MF's refinement and subtly would be quite your thing!The LX LPS distortion is vanishingly low, typically less than 0.007% across the audio band.Overload margin is exemplary. Simply put, it is virtually impossible for any real world cartridge to overload it.As we all know nothing is perfect, but the LX2-LPS gets very near. Technical Specifications:MMInput Impedance: 47 KΩInput Sensitivity: 3.0mVTotal Harmonic Distortion: 0.01%Signal to Noise Ratio: >80dBInput Overload Margin: 15dBMCInput Impedance: 100 ΩInput Sensitivity: 300μVTotal Harmonic Distortion: 0.01%Signal to Noise Ratio: >70dBInput Overload Margin: 22dBGeneralRIAA Response ±0.25dBPower Requirement 12-24V 100mA regulatedConnectionsMoving Magnet Input: 1pr RCA socketsMoving Magnet Loading: 1pr RCA socketsMoving Coil Input: 1pr RCA socketsMoving Coil Loading: 1pr RCA socketsPower Input: DC Jack (1.3mm inner pin, outer diam. 3.5mmDimensionsLength (including terminals) 197 mmWidth 172 mmHeight (including feet) 46.5 mmWeight(Unpacked / packed): 1.05 kg/ 1.50 kgIncluded accessoriesPower Supply

DescriptionNo one creates turntables and phono amps like Music Hall,and the PA15.3 is no exception.Fully adjustableThe pa15.3 is fully adjustable for gain and loading allowing you to really dial in and maximize the performance of your cartridge.Unrivaled performanceA real stand-out product that provides the functionality and sound quality of units easily costing 5 times the pa15.3’s modest price point.

New product release - mk4 versionThe P75 is a complete Phono solution in one compact unit. It is user adjustable and will handle virtually any type of cartridge on the market. The performance is noteworthy, with extreme RIAA accuracy, very low noise and outstanding dynamic range.The P75 incorporates a unique feature called "Phono Enhancer" (PE) which extracts the current signal, improve the magnetic field in the cartridge itself, which in turn provides an even more musical performance.The P75 mk4 introduces a new ultra­-low noise power supply that is electrically isolated from the input power. It takes the low grade single voltage DC supply from the AC adapter and converts it to dual high voltages required for true professional quality audio reproduction. Power supply noise is virtually unmeasurable. The P75 does not have any mains frequency or other low frequency components in the power supply and so hum problems that plague conventional phono amplifiers are eliminated.

Brand new for 2024, The Manley OASIS Phono Stage replaces the CHINOOKAt last, our favorite phono stage has been updated to operate with MANLEY POWER® which provides an even quieter blacker black background, yielding quicker sonic extremes over our older linear PSU designs. President EveAnna Manley recalls the moment she first made the comparison, “I brought a regular CHINOOK with its linear power supply, a stock unit, to Los Angeles to listen to it against a second CHINOOK that had been modified to work with our new MANLEY POWER® switch mode power supply. My buddy Pete Lyman at Infrasonic Mastering spun up some vinyl records that he had cut the masters for on his lathe. Using his mastering studio environment, we were able to conduct a very precise comparative listening test between the two units. And even though we could not see which unit we were listening to, the sonic differences were unmistakable, and we both heard the same superiority in the new power supply design. I still can’t believe what a stunning technical and sonic accomplishment MANLEY POWER represents, and delivers as we adopt more of our designs to take advantage of our proprietary system.”The OASIS Phono Stage offers an improvement in convenience over the older CHINOOK as the GAIN selections have been brought out from inside the chassis to the rear panel for easier access residing next to the resistive and capacitive loading DIP switches. There are tons of loading options to mate with any Moving Coil or Moving Magnet cartridge. Once you have set your GAIN and Loading for your cartridge, you’re done! Set it and forget it! The OASIS sports an upgraded more luxurious chassis design while its efficient internal build keeps the price affordable. And like all Manley products, each OASIS Phono Stage is loyally handcrafted in the USA by American men and women at our Southern Californian factory located just 35 miles east of Los Angeles.

Get the most out of your vinyl with NVC TT. Very easy to use, it is perfectly compatible with any turntable with MC cartridges and MM cartridges, and easily connects to NAC 332 or NSC 222 preamplifiers. When linked with its dedicated power supply, NPX TT, it offers high performance.

Vinyl replay makes a huge contribution to the enjoyment of recorded music. At its best, vinyl has a uniquely engaging and musical quality, and with the SuperLine phonostage, the best of vinyl just gets better. The SuperLine is a high performance moving-coil phono stage built in the Naim Audio aluminium reference enclosure with an anodised front panel. It brings all Naim Audio's latest analogue electronic design and environmental isolation techniques to bear on the most delicate analogue element of any hi-fi system - the moving-coil phono signal. The SuperLine requires an external power supply - either the power supply output of an appropriate Naim Audio preamplifier or the SUPERNAIT and NAIT XS integrated amplifiers, or, for optimum performance, a dedicated FlatCap XS, HiCap or SuperCap. SuperLine brings out all that's best in vinyl replay - timing, pitch accuracy, clarity, detail, and the unmistakable naturalness that records can deliver in abundance. Features: RCA and BNC inputs Moving coil only, with cartridge impedance matching adjustment (20 different load combinations possible)  Suspension system for delicate electronics as used in 500 Series 24V supply voltage from NaimUniti 2, NAIT XS 2, SUPERNAIT 2, Naim Audio preamplifier (except NAC-N 172 XS), FlatCap XS, HiCap or SuperCap required Bead-blasted, black anodised front panel Technology & Craft The heart of the SuperLine is a new, two-stage single-ended Class A discrete amplifier with part-passive RIAA filtering that runs off 25 internally regulated power supplies and features the transistor "quiet room" thermal isolation technique originally developed for the NAP 500 power amplifier. Environmental isolation is also ensured by the SuperLine's massive sub-chassis and high-Q spring suspension system - used here for the first time on a phono amplifier. Duplicate phono and BNC sockets provide input versatility, and cartridge impedance matching adjustment is provided by four resistive and three capacitive load plugs. In combination with the SuperLine's internal input load, twenty different standard load combinations are possible The SuperLine is also available in a lower gain model, SuperLine E. The SuperLine E is identical to the standard SuperLine except that is has been designed for use with cartridges that have a higher output voltage than most popular moving coils: for example high output moving coils. Audio Inputs: Other Inputs: 2 x 5-pin DIN for loading plugs Analogue Input: BNC, RCA Input Sensitivity: 100μV - 500μV, SuperLine E: 200μV - 1mV Audio Outputs: Crosstalk: >80dB (20Hz - 20kHz) THD + N: 200kHz -3dB Gain: 64dB at 1kHz, SuperLine E: 58dB at 1kHz Finish: Case: Black powder coated Front: Bead blasted and black anodised Phono Specific: Input Load Options: 10kΩ, 1k, 500Ω, 220Ω, 100Ω, 100pF, 1nF, 5.6nF, 10nF Input Overload: 5mV rms (1kHz), SuperLine E: 10mV RMS (1kHz) High Pass Filter: 10Hz RIAA Accuracy: ±0.1dB (20Hz - 20kHz) Physical: Shipping Weight: 9 kg Shipping Dimensions: 210 x 280 x 410 mm Weight: 7.7 kg Dimensions (HxWxD): 87 x 207 x 314 mm Power: Power Supply Options: NaimUniti, NAIT XS, SuperNait, 152XS, 202, 282, 252, 552, FlatCap XS, HiCap, SuperCap Supply Voltage: 24V Supplied with: Supplied with: Load Plug

DescriptionHigh-end phono preamplifier Today, many amplifiers do not have a specific phono cartridge input. The MINI 2 Phono is an ideal phono preamplifier for these hifi systems. It accepts MM and high-output MC cartridges and offers an audiophile music experience at an entry-level price.Advanced circuitry and shielding Advanced circuitry keeps noise and distortion at a surprisingly low level. The metal case shielding and an outboard DC power supply leave no risk for external interference. Because of its small casing, MINI 2 Phono can be placed near the turntable. Input and output sockets are gold-plated for preservation of quality. MINI 2 Phono can easily be connected to a line-input (AUX etc) of your amplifier.

The MX-VYNL is a fully balanced, very high performance phono stage, able to operate with virtually any moving coil or moving magnet cartridge. With both traditional RCA inputs and our unique XLR fully balanced connection the MX-VYNL can be connected to 2 turntables simultaneously.The MX-VNYL offers a wide range of input impedance settings for moving coil cartridges as well as several capacitance settings for moving magnet units. Unlike many of our competitors units the MX-VYNL allows easy adjustment of these settings while playing. This allows easy experimentation and tuning to find the optimum setting for all your equipment.The MX-VYNL also includes our renowned RIAA correction that offers extremely accurate results to beyond 80kHz. That may sound extreme, but there is a good deal of information above 20 kHz that needs correction. If it isn’t corrected, it will show itself as ringing and overshoot.With both extraordinarily low noise and exceptional overload margin the MX-VYNL can comfortably handle even the most demanding of cartridges and satisfy the most discerning of listeners.Features:Fully balanced XLR and traditional RCA inputsFully balanced XLR and traditional RCA outputsFully isolated inputs allow for switching between two turntables at onceAdjustable input impedance on MC whilst it is playingAdjustable capacitance on MM whilst it is playingVery wide overload marginAccurate RIAA to beyond 80kHzIncredible noise ratioLow impedance outputState of the art SMD technologyBeautiful aesthetics and build quality

The Fono MM MK5 phono stage has been designed to be effective, easy to use and above all, to reproduce music. The Fono MM MK5 uses a fully discrete, cascaded, complementary amplifier input stage, a configuration designed to optimise the performance of your moving magnet cartridge. Now housed in a brand new redesigned case to match the new Fono MC and Rega’s latest range of electronic components offering a modern look guaranteed to integrate in to any hi-fi system.The perfect partnerThe aesthetic design of the Fono MM was as important as the quality of its electrical capabilities, so it benefits from the same updated aluminium case as the Rega Neo and Fono MC amplifier, giving it a design which offers a familiar feel and moreover brings it in line with its illustrious bigger brothers. The RIAA equalization has been split into two stages to minimise interaction. Polyester capacitors have been used in the signal path and polypropylene capacitors are used in the RIAA equalization circuits.

Turn on, Tranquillity.In a world full of noise, welcome to ZEN.Futuristic Features. Nostalgic Feeling.In a world where modern technology is ever-evolving, simplicity and connection are what we crave most. Nothing demonstrates this quite like the familiar act of picking your favourite LP, hearing the soft crackle before it starts, and sharing a story or two with friends as you listen together.If this is the type of connection you crave, then a well-designed phono stage is integral for your vinyl setup. It takes the subtle whispers of your cartridge and amplifies them hundreds of times, making your vinyl’s magic compatible with headphones, amps, receivers and speakers. The ZEN Phono 3 opens the door to that analogue world with style and substance. With an intelligent warp filter and versatile loading options, you will be able to hear your over-loved LPs as new and fully experiment with your system setup.Packed with trickle-down technology from our prestigious history with sister company AMR, the ZEN Phono 3 is a noise-free upgrade that will allow you to slip seamlessly back into the blissful world of vinyl.Superior Specification.Zen Phono 3 boasts futuristic features unlike any other entry-level stage:MM/MC with 36-72dB gain rangeIndependent loading adjustmentSuper-silent -151dBV noise floorPrecise RIAA with balanced outputIntelligent subsonic filterHigh-tech 1.2MHz clean power supplySuper Smart. Super Subsonic.Standard subsonic filters aren’t intelligent and are typically loathed by audiophiles. They filter not only the bass rumble from warped records but also the bass of the song.Our intelligent subsonic filter knows the difference between the two and only filters the warp, leaving the song completely intact, and without adding group delay.Your Cartridge. Your Rules.The ZEN Phono 3 supports four MM/MC gain selections from 36 to 72dB and four input impedance settings.Mix and match gain and loading settings independently of each other with the all-new loading button, ensuring optimum compatibility with a wide range of cartridges and allowing you to get the sound ‘just right’.Exacting Equalisation.At the vinyl mastering stage, records are pressed with an inverse RIAA equalisation curve applied. This needs to be undone on playback by the phono stage to reveal the magic of the music.ZEN Phono 3’s RIAA EQ circuitry uses multiple TDK C0G capacitors in parallel. This is for best stability and the least distortion.This allows for ZEN Phono 3’s RIAA playback equalisation curve to be within +/- 0.15dB tolerance from 20-20kHz, allowing you to hear your records more accurately than ever before.Its RIAA accuracy is on-par with more costly phono stages that use hand-selected capacitors.Shockingly Silent.ZEN Phono 3 has a high-tech clean power supply built directly into it, isolated on its own “island” and away from the rest of the board.The power supply’s isolation mitigates noise pollution of the analogue stage – ensuring that only the audio is amplified and allowing for the noise-floor to remain whisper quiet.ZEN Phono 3’s Equivalent Input Noise measures at -151dBV, which is 20dBV quieter than some Stereophile Class A+ phonos. *For optimal noise performance, ensure that you are providing the cleanest power to your Phono 3.The iFi iPower2 is an ultra-quiet, ultra-clean audiophile-grade power supply, featuring Active Noise Cancellation II technology to cancel out all incoming EMI and RFI noise. You’ll never feel powerless against noise and graininess again.

AT-PEQ30The AT-PEQ30 phono equalizer is designed specifically to upgrade a turntable with a built-in phono amplifier or to add a phono. It is compatible with turntables with VM (dual magnet), MM (moving magnet), and MC (moving coil) cartridges. The PEQ30 benefits from Audio-Technica’s years of analogue audio expertise and uses the finest quality parts in a layout that is optimized for low noise and minimum distortion.Selectable MM and MC input with fixed gain and impedance allows for compatibility with a wide range of moving magnet and moving coil cartridgesHigh-quality FET inputs ensure a low noise signal when incorporated with a negative feedback-type phono equalizer circuitPrecision components provide an excellent RIAA response for best-in-class performanceThe all metal construction enclosure provides superior isolation from radio and electronic noise interferenceThe machined aluminium front panel and gold-plated input/output RCA connectors are examples of the high-grade material used throughout

DESCRIPTIONWith the renewed international enthusiasm for the vinyl format, a world-class phono preamplifier or RIAA stage is more important in a reference setup than ever before.The ECP2-MKII has become a new favorite of reviewers and enthusiasts alike. A benchmark product in its price bracket, much like other Electrocompaniet products. It incorporates state-of-the-art instrumentation and operational amplifiers and highest quality discrete components in the signal path. Of course it is all DC coupled. The ECP2-MKII introduces new chassis and front plate design, in line with our other products in the Classic Line. It will make your vinyl records sing like no other phono preamplifier we know of, and it seems the industry agrees with us.ADJUSTABLE GAINThe ECP2-MKII can accommodate any imaginable pickup, MM or MC thanks to its extremely configurable input stage, adjustable gain and the ECP 2 MKII is strictly matched to the RIAA curve.BALANCED AUDIOECP 2 MKII incorporates state-of-the-art instrumentation and operational amplifiers and highest quality discrete components in the signal path. Of course it is all DC coupled.

DescriptionThe Rega Fono Mini A2D-V2 is a high quality phono pre-amplifier for use with any moving magnet cartridge. The addition of USB interface allows you to easily transfer vinyl to your PC. The Fono Mini A2D-V2 is designed to amplify the signal from a moving magnet cartridge to a suitable level for all line level inputs of an audio amplifier. The new Fono Mini A2D-V2 benefits from an extruded aluminium case and very user friendly front and back panels that make this phono pre-amplifier a very easy product to use.

DescriptionThe Rega Fono MC disk stage is designed to amplify the signal from a moving coil cartridge to a level which can feed into a 200mV line level input on a standard hi-fi amplifier.

DescriptionOur Symphonic phonostage brings advanced features and our proprietary technology to vinyl replay, enabling the easy integration of turntables into any system and yielding exceptional performance from your analogue music collection.Nestling in the Choral range, the Symphonic is our flagship MC phono stage, offering a range of advanced features over the entry-level Dual. The high-performance Symphonic uses our latest high-frequency power supply technology to exploit vinyl’s full potential, along with many new key features, to bring the performance levels in line with the Choral range, home of the DAVE DAC/preamp.The Symphonic offers an almost infinite number of input impedance and gain options as well as balanced and unbalanced input options to the cartridge, making it a highly flexible device for integrating high-quality turntables into Chord systems. The comprehensive settings options are all externally selectable, with selections signified internally with illuminating LEDs.A rumble filter removes unwanted low-frequency rumble signals appearing on both channels. The Symphonic Phono stage conforms to the RIAA curve without the IEC roll-off when the Rumble filter is set to ‘off’ Preamps: CPA 2500, CPA 3000, CPA 5000, and CPA 8000. Preamps: CPA 2500, CPA 3000, CPA 5000, and CPA 8000.; this is commensurate with the high calibre of Chord amplification. The IEC curve response can be added by setting the Rumble filter to ‘on’. According to the wiring of the tone arm on the turntable used, the Symphonic can be operated in either an unbalanced or balanced mode.

DescriptionOur Symphonic phonostage brings advanced features and our proprietary technology to vinyl replay, enabling the easy integration of turntables into any system and yielding exceptional performance from your analogue music collection.Nestling in the Choral range, the Symphonic is our flagship MC phono stage, offering a range of advanced features over the entry-level Dual. The high-performance Symphonic uses our latest high-frequency power supply technology to exploit vinyl’s full potential, along with many new key features, to bring the performance levels in line with the Choral range, home of the DAVE DAC/preamp.The Symphonic offers an almost infinite number of input impedance and gain options as well as balanced and unbalanced input options to the cartridge, making it a highly flexible device for integrating high-quality turntables into Chord systems. The comprehensive settings options are all externally selectable, with selections signified internally with illuminating LEDs.A rumble filter removes unwanted low-frequency rumble signals appearing on both channels. The Symphonic Phono stage conforms to the RIAA curve without the IEC roll-off when the Rumble filter is set to ‘off’ Preamps: CPA 2500, CPA 3000, CPA 5000, and CPA 8000. Preamps: CPA 2500, CPA 3000, CPA 5000, and CPA 8000.; this is commensurate with the high calibre of Chord amplification. The IEC curve response can be added by setting the Rumble filter to ‘on’. According to the wiring of the tone arm on the turntable used, the Symphonic can be operated in either an unbalanced or balanced mode.

The reference Aura MC stage is the culmination of decades of electronic design development. We have created the ultimate, fully adjustable, three-stage, all symmetrical pre-amplifier designed purely to extract the very best performance from your moving coil cartridge and vinyl playback system. Design Innovation Built into a completely re-designed custom case, the Aura is dedicated to moving coil cartridges and stays clear of any compromises. We have avoided including any superfluous functions as they obstruct the signal path and degrade the sound quality. The Aura phono pre-amp incorporates remarkable and innovative design ideas. If you are a vinyl connoisseur, then the Aura MC is an absolute must for demonstration. First Stage The first stage is a symmetrical, complementary class A amplifier, using parallel connected Linear Systems ultra-low noise FET (Field Effect Transistor) transistors configured as a symmetrical compound pair input stage. The use of FET transistors ensures there is no bias current flowing in the cartridge coil so as not to upset the delicate magnetic geometry of the cartridge. The input circuit configuration also alleviates the use of any coupling components between the cartridge output and the input stage FET transistors, which would degrade the sound. The complementary ultra-low noise FET transistors are carefully graded and matched for optimum performance. This stage drives the passive high-frequency part of the RIAA equalisation stage. Second Stage  The second stage is a symmetrical, class A, differential amplifier with a common base driver stage; this is also used as the active amplifier in the low-frequency part of the RIAA equalisation stage. Third Stage The third stage inverts the signal to provide the balanced output along with the output of the second stage; the third stage uses the same circuit topology as used in the second stage. The power supply is a symmetrical, discrete tracking power supply using fast diodes and a low noise voltage reference. Each stage has its own localised power supply and LED referenced current generators. To maximise headroom, the Aura has a power supply voltage, which is 60% higher than normally found in such a pre-amplifier. Very high quality, polypropylene capacitors have been used in the signal path. 1% tolerance polypropylene capacitors are used in the RIAA EQ stages and audio grade capacitors are used in the rest of the circuit. Gain, Mute and Mono switching is implemented using high-quality relays.

ARIA MK3 MM/MC Housed within our latest half width custom designed case to give it a fresh new look and match the range are two entirely separate, high performance phono stages. One fully adjustable, dedicated moving coil and one moving magnet. Each stage is designed and engineered to maximise the potential of your vinyl system whilst remaining easy to use and set up. The Aria is an “all analogue amplifier” with no digital control circuitry. The fully aluminium case screens the internal circuit from any stray RFI signals. Our designers have avoided including any superfluous gadgets as they obstruct the signal path and degrade the sound quality. The Aria incorporates many innovative design ideas including a self-adjusting servo control to keep the MC input circuit at its optimum, compensating for any variations in ambient or operating temperature. Both stages have their own separate input sockets and input pre-amplifier circuitry. This enabled us to design bespoke input circuitry for each cartridge type without compromise. Signal switching is performed at high level and low impedance (via relays) ensuring there is no degradation of the signal. Key Features High performance switchable MC & MM stage Fully adjustable MC stage MC input uses parallel connected low noise FET's MM input uses low noise bipolar transistors Custom designed case All analogue amplifier Bespoke input circuitry for MM & MC Lifetime warranty against manufacture defects MM Stage design & features The MM input uses low noise, bipolar input transistors also configured as a compound pair. There are two separate power supplies for each channel and further sub-power supplies for each of the low noise input circuits. Nichicon FG electrolytic capacitors have been used in critical positions throughout the power supplies. Polypropylene capacitors have been used in the signal path and equalization networks. Discrete circuitry is used throughout the signal path ensuring full control of the circuit design. MC Stage Design & Features The MC input uses parallel connected, low noise FETs (Field Effect Transistors) configured as a compound pair. The use of FET transistors ensures there is no bias current flowing in the cartridge coil so as not to upset the delicate magnetic geometry of the cartridge. The MC input has the provision for selecting resistive input loading of 70 Ω to 400 Ω and capacitive loading of 1000 pF to 4200 pF. The input sensitivity can be changed by 6 dB via the back panel.

The M3x ViNYL is a phono stage, designed to be without any practical limits. Connectivity is straight forward. You have an input and an output. Neither of them can be overloaded at the input or limited in the output driving capacity. It can be set for either MM or MC and exact loading. It offers state-of-the art technical and sonic performance just like the M6x ViNYL, but at a cheaper entry level to the epitome of the true spirit of high-end audio. Design Philosophy The M3x ViNYL has been switched, just like in its bigger brother the M6x ViNYL, to an entirely discrete circuitry, which results in better technical measurements and better sound. It is equipped with one single-ended input and output. But the important question is: what is so special about discrete circuits? Although it is Musical Fidelity’s lowest price amplifier, it embodies our hallmark values of uncoloured, stress-free sound, outstanding technical performance and great value for money. The Advantage of Discrete Circuits A discrete circuit is composed of electronic components which are disparate, individual devices, also called discrete components. These can be “passive” components, like resistors, capacitors and inductors, as well as “active” components, which in our case are transistors. The opposite to this would be an integrated circuit, which uses operational amplifiers (Op-Amps) in the signal chain. In our industry we employ specialised Op-Amps built for audio applications, which allow us to produce very small and efficient electronics, as well as saving the time of design engineers. However, countless hours of listening tests and years of experience have shown us that even the very best Op-Amps do not tend to be so neutral, natural, dynamic or vivid – all of which are characteristics of the Musical Fidelity “sound”. For that reason, we’re rediscovering our passion for traditional, discrete designs. Where standard phono pre-amplifiers with integrated circuits have a few tens or hundreds of components, discrete designs will employ hundreds or thousands of components by comparison. That makes for an extended design process, but in our opinion results in the best sound for your money. Toroidal Power Transformer The special audio transformer with low core saturation decreases the level of electromagnetic radiation, which is essential because otherwise any phono amplifier will never be able to work correctly. Together with the distance between transformer and amplification section and the electromagnetic shielding, we are creating an incredibly high signal to noise ratio. If we are working with the few hundreds of microvolts from a phono cartridge, everything is playing its role; every decibel of signal to noise ratio is crucially important. For the first time, we have implemented our new proprietary power supply solution that has zero standby power consumption. Absolutely zero! It is a super green product and we are sure, there isn’t any other product in existence with an ecological standby function like this. Split Passive EQ Many other phono stages are using a single equalization network in a global feedback loop. By means of an EQ network, the amplified signal from the output of the phono preamp is brought back to the input of the phono preamp. This is the before mentioned feedback loop, and the results, as you can imagine, are not in accordance with the high standards in Musical Fidelity design philosophy. The M3x ViNYL uses split passive equalization in separate amplification stages without global negative feedback loops for its RIAA curve. This is more costly to design and implement but ensures the most accurate representation of the ideal EQ curve. Split passive equalization allows for better impedance matching and lower deviation from the ideal RIAA curve. High-Tech Mechanical and Electrical Engineering - Hand Made in the EU M3x ViNYL has a steel chassis and a thick, heavy aluminium frontplate, which brings outstanding rigidity to the entire system and at the same time splendid isolation against outside interference. Key factor in keeping signal to noise ratios on the highest possible leveld is the huge distance between power transformer and amplifier section. The quality of the outside chassis finish, which is beyond beautiful, as well as the electronics inside - all wired by hand - is maintained by the highest manufacturing standards which we now achieve by fully switching the production to be entirely Made in the EU! M3si In Brief MM and MC input Exact loading options for any cartridge Fully discrete circuit board design Special low core saturation toroidal transformer custom designed for phono stage requirements Environmental friendly - absolutely zero standby power consumption Split Passive RIAA and DECCA EQ Heavy aluminium frontplate with steel chassis Minimal electromagnetic interference from power supply to phono preamp Big chassis design enables huge distance between power transformer and amplifier section Made in the EU

The M3x ViNYL is a phono stage, designed to be without any practical limits. Connectivity is straight forward. You have an input and an output. Neither of them can be overloaded at the input or limited in the output driving capacity. It can be set for either MM or MC and exact loading. It offers state-of-the art technical and sonic performance just like the M6x ViNYL, but at a cheaper entry level to the epitome of the true spirit of high-end audio. Design Philosophy The M3x ViNYL has been switched, just like in its bigger brother the M6x ViNYL, to an entirely discrete circuitry, which results in better technical measurements and better sound. It is equipped with one single-ended input and output. But the important question is: what is so special about discrete circuits? Although it is Musical Fidelity’s lowest price amplifier, it embodies our hallmark values of uncoloured, stress-free sound, outstanding technical performance and great value for money. The Advantage of Discrete Circuits A discrete circuit is composed of electronic components which are disparate, individual devices, also called discrete components. These can be “passive” components, like resistors, capacitors and inductors, as well as “active” components, which in our case are transistors. The opposite to this would be an integrated circuit, which uses operational amplifiers (Op-Amps) in the signal chain. In our industry we employ specialised Op-Amps built for audio applications, which allow us to produce very small and efficient electronics, as well as saving the time of design engineers. However, countless hours of listening tests and years of experience have shown us that even the very best Op-Amps do not tend to be so neutral, natural, dynamic or vivid – all of which are characteristics of the Musical Fidelity “sound”. For that reason, we’re rediscovering our passion for traditional, discrete designs. Where standard phono pre-amplifiers with integrated circuits have a few tens or hundreds of components, discrete designs will employ hundreds or thousands of components by comparison. That makes for an extended design process, but in our opinion results in the best sound for your money. Toroidal Power Transformer The special audio transformer with low core saturation decreases the level of electromagnetic radiation, which is essential because otherwise any phono amplifier will never be able to work correctly. Together with the distance between transformer and amplification section and the electromagnetic shielding, we are creating an incredibly high signal to noise ratio. If we are working with the few hundreds of microvolts from a phono cartridge, everything is playing its role; every decibel of signal to noise ratio is crucially important. For the first time, we have implemented our new proprietary power supply solution that has zero standby power consumption. Absolutely zero! It is a super green product and we are sure, there isn’t any other product in existence with an ecological standby function like this. Split Passive EQ Many other phono stages are using a single equalization network in a global feedback loop. By means of an EQ network, the amplified signal from the output of the phono preamp is brought back to the input of the phono preamp. This is the before mentioned feedback loop, and the results, as you can imagine, are not in accordance with the high standards in Musical Fidelity design philosophy. The M3x ViNYL uses split passive equalization in separate amplification stages without global negative feedback loops for its RIAA curve. This is more costly to design and implement but ensures the most accurate representation of the ideal EQ curve. Split passive equalization allows for better impedance matching and lower deviation from the ideal RIAA curve. High-Tech Mechanical and Electrical Engineering - Hand Made in the EU M3x ViNYL has a steel chassis and a thick, heavy aluminium frontplate, which brings outstanding rigidity to the entire system and at the same time splendid isolation against outside interference. Key factor in keeping signal to noise ratios on the highest possible leveld is the huge distance between power transformer and amplifier section. The quality of the outside chassis finish, which is beyond beautiful, as well as the electronics inside - all wired by hand - is maintained by the highest manufacturing standards which we now achieve by fully switching the production to be entirely Made in the EU! M3si In Brief MM and MC input Exact loading options for any cartridge Fully discrete circuit board design Special low core saturation toroidal transformer custom designed for phono stage requirements Environmental friendly - absolutely zero standby power consumption Split Passive RIAA and DECCA EQ Heavy aluminium frontplate with steel chassis Minimal electromagnetic interference from power supply to phono preamp Big chassis design enables huge distance between power transformer and amplifier section Made in the EU

For the record Matt polished black. Super quiet noise floor. Our phono stage circuitry uses only the best audiophile components. Computer matched op-amps, high-gain bi-polar output transistors to Nichicon audio-grade capacitors. And much more. The iPhono3 Black Label sounds stellar. Hear into your LP. Silent nights in With a stunning, super-low 85dB noise floor (per Stereophile standard) the iPhono3 Black Label is out there. One of the quietest phono stages. Period. Like any good phono stage, it amplifies the signal, not the noise. The whisper-quiet noise floor is there for any home audio system to discern. Take it for a test drive from the comfort of your favourite listening chair. Exacting equalisation Precise EQ curve and explosive 108dB dynamic range. Your listening room becomes a concert hall. The AMR PH-77, the $12,000 larger sibling with 23 equalisation curves, remains the vinyl benchmark to this day. Trickle-down tech used in the iPhono3 Black Label means it features the 6 most popular stereo EQ curves. Try the infamous 1812 Overture ‘torture test’. Won’t be the same again. The iPhono3 Black Label will have you trying ‘just one more LP’ into the wee, small hours. Set and forget Your pickup (stylus) has been lovingly crafted. Whether it’s MM or MC, no two cartridges are identical in performance. The iPhono3 Black Label, like the AMR PH-77 from which it descends, enables you to set the precise load/gain for the cartridge you have. Squeeze every last drop of performance out of your precious pickup. Spec’d to thrill Beneath the modest footprint of the iPhono 3 Black Label are Class A TubeState and DirectDrive Servoless technologies. Specially developed by AMR for iFi audio. All underpinned by some quite special audiophile components from Burr-Brown, TDK and Nichicon. To name but a few. With such dedicated circuitry and devoted components, it has a whisper-quiet noise floor and measured THD of an incredible

Exact and preccise loading for MM and MC cartridges -RCA and balanced outputs -3 Inputs, load settings are stored for each input individually.

Exact and preccise loading for MM and MC cartridges -RCA and balanced outputs -3 Inputs, load settings are stored for each input individually.

There’s something in the Air.Our super affordable phono stage makes your vinyl sound purer than ever.Enjoy a purer listening experience with the ZEN Air Phono, our super affordable phono stage.A phono stage, also called a phono pre-amp, provides the connection between the record cartridge/pickup (stylus) and the amplifier.Turntable cartridges output a very small signal. This signal needs amplifying up to several hundred times the original size before it is loud enough for your amplifier. A phono stage increases the signal level from millivolts to volts.When vinyl was the standard for audio recording, the phono stage was built-in to receivers and amps, allowing direct connection of a turntable. These days most receivers and amps do not contain a phono stage so a separate unit is needed.It is a necessity for any turntable without a phono stage already built in. It will also upgrade a basic built-in phono stage in a turntable or amplifier system.Purer stillListening to music on vinyl is good for the soul. It sounds purer than listening to a track via your phone or computer.Make this experience purer still by reducing hiss, noise and rumble on your records with the ZEN Air Phono.MC and MMThere are two kinds of turntable cartridge – Moving Magnet and Moving Coil – and the ZEN Air Phono works with both of them.The MM setting is for cartridges with an output voltage of 2mV and higher.The MC setting for outputs less than 2mV.You use the gain switch on the rear to change this setting.It also has a precise RIAA equalisation setting to satisfy the most demanding vinyl lover.Engage warp driveAs we all know, records can become warped with age. With the ZEN Air Phono any warp on your records will be driven away by our ‘subsonic filter’.Normal subsonic filters remove ‘rumble’ AND bass and cause phase issues.Our unique AI phono sub-sonic filter removes ‘rumble’ only.

Naim Air Plug Z offers custom ohms loading for Superline phono preamp, for the best playback of various cartridges

RIAA Phono Preamplifier This phono preamplifier for Moving Magnet (MM) and Moving Coil (MC) pickup systems is based on the legendary Douglas-Self-Design. MM & MC There are two pickup systems for record players: Moving Magnet (MM) and Moving Coil (MC). Moving Magnet Moving magnet pickups generate a small voltage by moving a magnet between copper coils. MM pickups have a very high inductance and impedance. The Phonos offers a choice of three capacitors to correct the linearity of the frequency and phase response. The capacitances are 150pF, 220pF and 330pF. In the off-position the capacitance is determined by the capacitance of the cable. Moving Coil The MC pickup is also a small electromagnetic generator, but with the magnets firmly anchored and the coils moving between them, i.e. exactly the opposite of the MM pickup. The output voltage, however, is very low at only a few hundred microvolts and is therefore more sensitive to noise and induced hum. This makes preamplifier design a challenge, because the very low output voltage must be pre-amplified extremely noise-free. Phonos offers one of the most powerful phono preamplifiers for MC systems with up to 71.5 dB preamplification. Thanks to the 120V technology, the preamplifiers are extremely low-noise, linear and phase-locked. MC pickups have a very low inductance and impedance. This means that the effects of cable capacitance (from turntable to preamplifier) are negligible. The impedance, however, is relevant and can be set in six positions: 100, 220, 470, 2.2 k, 4.7 k, and 10 kOhm. If there is any doubt as to which impedance matches that of the pickup, the impedances can also simply be switched through until the linear frequency response is acoustically determined. Amplification The pre-amplification can be switched in three values. The normal gain value is +46 dB for MM and +67 dB for MC cartridges. In the -10 dB position, the phono produces enough output level for normal hi-fi equipment operating at a reference level of -10 dBV. In the +4 dB position, the output level is about as loud as that of modern DA converters at a reference level of 0dBfs = +15 dBu. Subsonic Filter The rumbling of the turntable’s drive mechanism is also amplified by the high amplification of the bass range due to RIAA equalization in playback. The Phonos offers a switchable subsonic filter to remove this rumble.  Connections Gold-plated RCA sockets are available for connecting the turntable and for outputting to a preamplifier such as the Director Mk2 or the Elector.  A ground connection for the turntable is designed as banana plug socket. The ground lead can be either clamped or plugged in. RIAA Equalization RIAA equalization is a specification for the recording and playback of records proposed by the Recording Industry Association of America (RIAA). The RIAA equalization curves introduced a global de facto industry standard for vinyl records in 1954. RIAA equalization uses pre-emphasis to reduce low frequencies and boost high frequencies when the record is cut (blue RIAA curve). The bass is reduced by up to 20 dB to provide more space and longer record play time. The high frequencies are boosted by up to 25 dB to increase the signal-to-noise ratio between the noise and the hot of the record media to the audio signal. During playback, exactly the opposite happens in the phono. The de-emphasis filter (red RIAA curve) compensates for the pre-emphasis and the result is a linear frequency response. Douglas Self Design The RIAA equalization of the phono was developed according to the recommendations of Douglas Self. Idea: Many small capacities instead of a few large capacities. Advantages: The capacitors charge and discharge faster, which results in better resolution and faster impulse response. Only audiophile Styroflex capacitors are used in the entire RIAA equalizer. About the person: Douglas Self is a British electronics engineer with a strong penchant for audio. He holds honorary degrees from Cambridge University and teaches psychoacoustics at the University of Sussex. Specifications: Analog Input & Output: RCA Input impedance (MM): 47 kΩ Input impedance (MC): switchable Output impedance: 75 Ω Frequency range (-3 dB): 4 Hz – 300 kHz Crosstalk (1 kHz): -80 dBu Moving Magnet (MM) Preamplifier Amplification (Norm): 46 dB Amplification (-10 dB): 36 dB Amplification (+4 dB): 50 dB Capacitance (switchable): Off, 150 pF, 220 pF and 330 pF Noise (A-weighted; 46 dB amplification): -85.3 dBu Dynamic range: 131.3 dB Moving Coil (MC) Preamplifier Amplification (Norm): 67 dB Amplification (-10 dB): 56 dB Amplification (+4 dB): 71.5 dB Impedance (switchable): 100 Ω, 220 Ω, 470 Ω, 2.2 kΩ, 4.7 kΩ, 10 kΩ Noise (A-weighted, 67 dB amplification): -61.7 dBu Dynamic range: 128.7 dB Internal Linear Power Supply with Shielded Toroidal Transformer Operating voltage for analog audio: +/- 60 V Operating voltage for relays and LEDs: + 12 V Mains Power Supply Mains voltage (selectable, see fuse chamber): 230 V AC / 50; 115 V AC / 60 Hz Fuse for 230 V: T 500 mA Fuse for 115 V: T 1 A Power consumption: max. 30 VA Stand-by power consumption: < 0,3 W Dimensions & Weight W x H x D (width x height incl. feet x depth): 278 x 100 x 330 mm Unit weight: 3.2 kg Shipping weight (incl. packaging): 4.3 kg

RIAA Phono Preamplifier This phono preamplifier for Moving Magnet (MM) and Moving Coil (MC) pickup systems is based on the legendary Douglas-Self-Design. MM & MC There are two pickup systems for record players: Moving Magnet (MM) and Moving Coil (MC). Moving Magnet Moving magnet pickups generate a small voltage by moving a magnet between copper coils. MM pickups have a very high inductance and impedance. The Phonos offers a choice of three capacitors to correct the linearity of the frequency and phase response. The capacitances are 150pF, 220pF and 330pF. In the off-position the capacitance is determined by the capacitance of the cable. Moving Coil The MC pickup is also a small electromagnetic generator, but with the magnets firmly anchored and the coils moving between them, i.e. exactly the opposite of the MM pickup. The output voltage, however, is very low at only a few hundred microvolts and is therefore more sensitive to noise and induced hum. This makes preamplifier design a challenge, because the very low output voltage must be pre-amplified extremely noise-free. Phonos offers one of the most powerful phono preamplifiers for MC systems with up to 71.5 dB preamplification. Thanks to the 120V technology, the preamplifiers are extremely low-noise, linear and phase-locked. MC pickups have a very low inductance and impedance. This means that the effects of cable capacitance (from turntable to preamplifier) are negligible. The impedance, however, is relevant and can be set in six positions: 100, 220, 470, 2.2 k, 4.7 k, and 10 kOhm. If there is any doubt as to which impedance matches that of the pickup, the impedances can also simply be switched through until the linear frequency response is acoustically determined. Amplification The pre-amplification can be switched in three values. The normal gain value is +46 dB for MM and +67 dB for MC cartridges. In the -10 dB position, the phono produces enough output level for normal hi-fi equipment operating at a reference level of -10 dBV. In the +4 dB position, the output level is about as loud as that of modern DA converters at a reference level of 0dBfs = +15 dBu. Subsonic Filter The rumbling of the turntable’s drive mechanism is also amplified by the high amplification of the bass range due to RIAA equalization in playback. The Phonos offers a switchable subsonic filter to remove this rumble.  Connections Gold-plated RCA sockets are available for connecting the turntable and for outputting to a preamplifier such as the Director Mk2 or the Elector.  A ground connection for the turntable is designed as banana plug socket. The ground lead can be either clamped or plugged in. RIAA Equalization RIAA equalization is a specification for the recording and playback of records proposed by the Recording Industry Association of America (RIAA). The RIAA equalization curves introduced a global de facto industry standard for vinyl records in 1954. RIAA equalization uses pre-emphasis to reduce low frequencies and boost high frequencies when the record is cut (blue RIAA curve). The bass is reduced by up to 20 dB to provide more space and longer record play time. The high frequencies are boosted by up to 25 dB to increase the signal-to-noise ratio between the noise and the hot of the record media to the audio signal. During playback, exactly the opposite happens in the phono. The de-emphasis filter (red RIAA curve) compensates for the pre-emphasis and the result is a linear frequency response. Douglas Self Design The RIAA equalization of the phono was developed according to the recommendations of Douglas Self. Idea: Many small capacities instead of a few large capacities. Advantages: The capacitors charge and discharge faster, which results in better resolution and faster impulse response. Only audiophile Styroflex capacitors are used in the entire RIAA equalizer. About the person: Douglas Self is a British electronics engineer with a strong penchant for audio. He holds honorary degrees from Cambridge University and teaches psychoacoustics at the University of Sussex. Specifications: Analog Input & Output: RCA Input impedance (MM): 47 kΩ Input impedance (MC): switchable Output impedance: 75 Ω Frequency range (-3 dB): 4 Hz – 300 kHz Crosstalk (1 kHz): -80 dBu Moving Magnet (MM) Preamplifier Amplification (Norm): 46 dB Amplification (-10 dB): 36 dB Amplification (+4 dB): 50 dB Capacitance (switchable): Off, 150 pF, 220 pF and 330 pF Noise (A-weighted; 46 dB amplification): -85.3 dBu Dynamic range: 131.3 dB Moving Coil (MC) Preamplifier Amplification (Norm): 67 dB Amplification (-10 dB): 56 dB Amplification (+4 dB): 71.5 dB Impedance (switchable): 100 Ω, 220 Ω, 470 Ω, 2.2 kΩ, 4.7 kΩ, 10 kΩ Noise (A-weighted, 67 dB amplification): -61.7 dBu Dynamic range: 128.7 dB Internal Linear Power Supply with Shielded Toroidal Transformer Operating voltage for analog audio: +/- 60 V Operating voltage for relays and LEDs: + 12 V Mains Power Supply Mains voltage (selectable, see fuse chamber): 230 V AC / 50; 115 V AC / 60 Hz Fuse for 230 V: T 500 mA Fuse for 115 V: T 1 A Power consumption: max. 30 VA Stand-by power consumption: < 0,3 W Dimensions & Weight W x H x D (width x height incl. feet x depth): 278 x 100 x 330 mm Unit weight: 3.2 kg Shipping weight (incl. packaging): 4.3 kg

The V90-LPS is an outstanding phone stage / amplifier designed to provide the ideal interface between high performance turntables and Hi-Fi amplifiers. Its signal path has been designed to offer a clean and transparent connection for your music to ensure it is heard exactly as the artist intended.Housed in a sleek, attractive case the V90-LPS balances high-end performance with incredible value and is the perfect partner for a wide range of turntables. It’s separate Moving Magnet (MM) and Moving Coil (MC) inputs are each tuned to offer the best possible performance from their respective cartridges and convey a startlingly realistic audio performance. While the V90-LPS offers an outstanding musical experience it also represents amazing value for money. Listeners can look forward to hours of listening pleasure that is usually only delivered by considerably more expensive products.Specifications:PerformanceInput impedance: 47kOhm (MM), 100Ohm (MC)Input sensitivity: 3.0mV (MM), 400µV (MC) - for 300mV outTotal harmonic distortion: 0.01% (MM/MC) - @ 1kHz, 300mV outFrequency Response: +0, –0.1dB, 20Hz to 20 kHzSignal / Noise ratio (A weighted): >80dB (MM), >80dB (MC)Input overload margin: 15dB (MM), 22dB (MC)RIAA response: +/- 0.25dBConnectionsMM: 1 pair RCA socketsMC: 1 pair RCA socketsLine level outputs: 1 pair RCA socketsPower input: 1.3mm DC power socketOutputs1x line level RCA (phono)GeneralDimensions (inc. terminals & feet) - WxHxD (mm): 170 x 47 x 102Weight (unpacked / packed): 600g / 1.1 kgSupplied Accessories1x 12v 500mA DC power supply  

Tube phono-preamplifier Innovative miniature sized phono preamplifier with tube output and high end sound! Tube Box S2 is our very first product to feature a fully discreet circuit design without using any operational amplifiers (OpAmps). It also is the first product to come with replaceable tubes for tube rolling and sound-shaping. This gives the customer many options to pick from and alter the sound signature to his preference. Tube Box S2 will give a full and relaxed laid back sound with lush mids, just like you would expect it from a much bigger high end tube phono pre-amplifier. It offers support for both MM and MC cartridges and comes with many gain settings to be switched on the front panel. Five variable input impedance settings are available to adjust to any MM cartridge, the 47k ohm input impedance setting is fixed and suited for high output MC cartridges. The aluminium/metal casing is adapted to our DS2 line in looks and protects against vibrations and electromagnetic interferences for superior sound. Features:  Suitable for MM and MC cartridges Precise RIAA equalisation in two parts, passive/active Fully discreet circuit design without OpAmps 2x ECC83 tubes (replaceable) Front-sided Subsonic filter button Front-sided Gain control Ultra low noise circuitry with FET input stage Dual mono circuitry for optimized channel separation Polystyrene capacitors used where possible Gold-plated RCA in- and outputs External power adaptor and multiple internal power supplies Well-filtrated high-voltage anode power supply Sandwich alu/metal casing protects from vibrations and electromagnetic interference Available in silver or black Specifications:  Tubes 2 x ECC83 (12AX 7A) Input impedance 10 ohms, 100 ohms, 1 kohm, 2 kohms Input capacitance/impedance 47pF, 147pF, 267pF, 367 pF, 487 pF and 587 pF* / 47 kohms, Together with other input impedance settings without any influence! Input gain 40 dB, 43 dB / 50 dB, 60 dB und 63 dB Noise floor 80 dB (A weighted) at 40 dB input gain, 75dB (A weighted) at 50 dB and 63 dB input gain THD

Tube phono-preamplifier Innovative miniature sized phono preamplifier with tube output and high end sound! Tube Box S2 is our very first product to feature a fully discreet circuit design without using any operational amplifiers (OpAmps). It also is the first product to come with replaceable tubes for tube rolling and sound-shaping. This gives the customer many options to pick from and alter the sound signature to his preference. Tube Box S2 will give a full and relaxed laid back sound with lush mids, just like you would expect it from a much bigger high end tube phono pre-amplifier. It offers support for both MM and MC cartridges and comes with many gain settings to be switched on the front panel. Five variable input impedance settings are available to adjust to any MM cartridge, the 47k ohm input impedance setting is fixed and suited for high output MC cartridges. The aluminium/metal casing is adapted to our DS2 line in looks and protects against vibrations and electromagnetic interferences for superior sound. Features:  Suitable for MM and MC cartridges Precise RIAA equalisation in two parts, passive/active Fully discreet circuit design without OpAmps 2x ECC83 tubes (replaceable) Front-sided Subsonic filter button Front-sided Gain control Ultra low noise circuitry with FET input stage Dual mono circuitry for optimized channel separation Polystyrene capacitors used where possible Gold-plated RCA in- and outputs External power adaptor and multiple internal power supplies Well-filtrated high-voltage anode power supply Sandwich alu/metal casing protects from vibrations and electromagnetic interference Available in silver or black Specifications:  Tubes 2 x ECC83 (12AX 7A) Input impedance 10 ohms, 100 ohms, 1 kohm, 2 kohms Input capacitance/impedance 47pF, 147pF, 267pF, 367 pF, 487 pF and 587 pF* / 47 kohms, Together with other input impedance settings without any influence! Input gain 40 dB, 43 dB / 50 dB, 60 dB und 63 dB Noise floor 80 dB (A weighted) at 40 dB input gain, 75dB (A weighted) at 50 dB and 63 dB input gain THD

Tube phono-preamplifier Premium phono preamplifier with tube output and highend sound! This precision tube phono pre-amplifier benefits from outstanding circuit technology from Dr. Sykora and uses ultimate components. Compatible with both MM and MC cartridges. It offers connection for two turntables plus two selectable line outputs and a continuously variable selection of input impedance for low output MC cartridges while playing a record! Other features include input capacitance for MM cartridges and switchable subsonic, that prevents your amplifier and speakers of ultra low rumble below 20Hz. All components including tube output and polypropylene capacitors are audiophile-grade and guarantee a breathtaking sound experience. A perfect upgrade for ambitious vinyl lovers! Features: Suitable for MM and MC cartridges Precise RIAA equalisation Ultra low noise circuitry Selection between 2 phono inputs & 2 line outputs Dual mono circuitry for optimized channel separation Selectable input impedance (for MC: fix or variable) Selectable input capacitance (for MM) Selectable subsonic filter Gold-plated RCA in & outputs Sandwich alu/metal casing protects from vibrations and electromagnetic interference Finishes: silver or black, with/without wooden side panels (rosewood, walnut, eucalyptus) Specifications: Tubes 2 x ECC83 (12AX7) Input impedance Variable 10-1000 Ohm, fix 47 kOhm Capacitance 100 / 220 / 320 pF Gain MM / MC 40 / 45 / 50 / 60 / 65 dB Output voltage typically 500 mV/1kHz at 5mV/1kHz (at 40dB) SNR 88 dBA THD < 0.04% RIAA curve accuracy +/- 0.2dB/20Hz - 20kHz Subsonic filter 20Hz @ 12dB/octave Inputs 2 x Phono (RCA) Outputs 2 x Line (RCA) Power supply 18V/1000mA DC Power consumption max 490mA DC / < 0.5 Watt Standby Dimensions B x H x T 206 x 91 x 227 mm (Alu) 240 x 93 x 227 mm (Wood) Weight (without power supply) 1500 g (Alu) 1960 g (Wood)

Tube phono-preamplifier Premium phono preamplifier with tube output and highend sound! This precision tube phono pre-amplifier benefits from outstanding circuit technology from Dr. Sykora and uses ultimate components. Compatible with both MM and MC cartridges. It offers connection for two turntables plus two selectable line outputs and a continuously variable selection of input impedance for low output MC cartridges while playing a record! Other features include input capacitance for MM cartridges and switchable subsonic, that prevents your amplifier and speakers of ultra low rumble below 20Hz. All components including tube output and polypropylene capacitors are audiophile-grade and guarantee a breathtaking sound experience. A perfect upgrade for ambitious vinyl lovers! Features: Suitable for MM and MC cartridges Precise RIAA equalisation Ultra low noise circuitry Selection between 2 phono inputs & 2 line outputs Dual mono circuitry for optimized channel separation Selectable input impedance (for MC: fix or variable) Selectable input capacitance (for MM) Selectable subsonic filter Gold-plated RCA in & outputs Sandwich alu/metal casing protects from vibrations and electromagnetic interference Finishes: silver or black, with/without wooden side panels (rosewood, walnut, eucalyptus) Specifications: Tubes 2 x ECC83 (12AX7) Input impedance Variable 10-1000 Ohm, fix 47 kOhm Capacitance 100 / 220 / 320 pF Gain MM / MC 40 / 45 / 50 / 60 / 65 dB Output voltage typically 500 mV/1kHz at 5mV/1kHz (at 40dB) SNR 88 dBA THD < 0.04% RIAA curve accuracy +/- 0.2dB/20Hz - 20kHz Subsonic filter 20Hz @ 12dB/octave Inputs 2 x Phono (RCA) Outputs 2 x Line (RCA) Power supply 18V/1000mA DC Power consumption max 490mA DC / < 0.5 Watt Standby Dimensions B x H x T 206 x 91 x 227 mm (Alu) 240 x 93 x 227 mm (Wood) Weight (without power supply) 1500 g (Alu) 1960 g (Wood)

We may not build a turntable, but we have decades of experience making the most of the black magic offered by the vinyl LP. Our StageLine phonostage, available in either moving coil or moving magnet versions, can be powered just from our NAIT XS 2 amplifier or via its own dedicated power supply, such as a FlatCap XS. However you connect and configure it, you can be assured of the consummate musicality so fundamental to every Naim Audio product.  Features RCA inputs Moving coil or moving magnet versions available 24V supply voltage from NaimUniti 2, NAIT XS2, SUPERNAIT 2, Naim Audio preamplifier (except NAC-N172 XS & NAC-N 272), FlatCap XS, HiCap or SuperCap required.  Audio Inputs Analogue Input: RCA Input Sensitivity: K & S 100μV, E 400μV, N 2mV Audio Outputs Gain: N 35dB at 1kHz, K & S 60dB at 1kHz Finish Case: Black powder coated Front: Black powder coated Phono Specific Input Load Options: S= 470Ω//6.8nF, K= 560Ω//1nF, E= 560Ω//6.8nF, N= 47kΩ//470pF Physical Shipping Weight: 1.2 kg Shipping Dimensions: 100 x 170 x 265 mm Dimensions (HxWxD): 57 x 121 x 187 mm Power Power Supply Options: NaimUniti, NAIT XS, SuperNait, 152XS, 202, 282, 252, 552, FlatCap XS, HiCap, SuperCap Supply Voltage: 24V Supplied with: Supplied with Standard Interconnect

The Duo seems to exude an air of accomplishment. It’s a solid, lightweight piece of tech that just looks plain good... A rich and rewarding listening experience I just can’t tear myself away from... Few other options out there can match this kind of listening experience, which to put it mildly, is pretty amazing. Whether you’re dusting off your record collection or embracing analogue through the vinyl revival, there’s a unique experience to be had from the moment you drop the needle on your favourite album. To preserve the unique warmth of the vinyl sound, the Duo phono preamplifier has been carefully designed with a state-of-the-art switch mode power supply and a new surface mounted circuit board layout to reduce unwanted noise. Due to the low-level signals created by a turntable, not all hi-fi amplifiers will let you connect directly to a record player. The phono preamplifier boosts this signal to something a power amplifier can work with. The challenge at this stage though is that noise can easily be added. This is why we’ve designed the Duo around exceptional components that deliver the warm and detailed sound that’s synonymous with vinyl, all without distorting the signal from your moving magnet cartridge turntable. The switch mode power supply improves performance by switching outside of audible frequency to drastically reduce hum and new circuit board layout uses surface-mount components to reduce noise. Enjoy the warmth of vinyl privately thanks to Duo’s integrated headphone output. Uniquely, we integrated a 6.35mm headphone jack directly into the phono stage, so you can still enjoy your records when there’s no option to play out loud. The integrated headphone output also means no need to turn on your amplifier just to power your headphones, resulting in a more eco-friendly listening experience. If some records in your collection are a little worse for wear, the subsonic filter will help to eliminate low frequency rumbles that can be caused by imperfections within your vinyl. Combine this with the balance control for handling potential cartridge imbalances in your record player (that can cause a difference between the left and right channels) and the result is a detailed experience with accurate soundstage. The Duo phono preamplifier is green at heart with less than half a watt standby power consumption and auto power down feature if the unit isn’t used after a 20 minute period. This in turn gives the unit the same worldwide voltage for compatibility wherever you are in the world. Specifications: MAX POWER CONSUMPTION: 10W CARTRIDGE SUPPORT: Moving Magnet | Moving Coil GAIN @ 1KHZ: MM: 39dB | MC: 60dB NOMINAL OUTPUT: 300mV SENSITIVITY FOR NOMINAL OUTPUT: MM: 3.35mV | MC: 305uV EQUIVALENT INPUT NOISE (A-WEIGHTED): MM: ~0.09uV | MC: ~0.08uV RIAA CURVE ACCURACY: +/- 0.3dB 30Hz-50Hz SIGNAL TO NOISE RATIO GROUNDED INPUTS REF. 1V OUTPUT (20HZ-20KHZ BW): MM: >90dB | MC: >70dB THD+N 1KHZ (20-20KHZ BW): MM: 85dB | MC: 75dB DIMENSIONS (H X W X D): 48 x 215 x 159 mm (1.9 x 8.5 x 6.2") WEIGHT: 0.95kg (2.1lbs)

Enjoy every last detail from your vinyl collection with our highest quality moving magnet phono stage, the Solo Phono Preamplifier. Whether you’re dusting off your record collection or embracing analogue through the vinyl revival, there’s a unique experience to be had from the moment you drop the needle on your favourite album. To preserve the unique warmth of the vinyl sound, the Solo phono preamplifier has been carefully designed with a state-of-the-art switch mode power supply and a new surface mounted circuit board layout to reduce unwanted noise. Due to the low-level signals created by a turntable, not all hi-fi amplifiers will let you connect directly to a record player. The phono preamplifier boosts this signal to something a power amplifier can work with. The challenge at this stage though is that noise can easily be added. This is why we’ve designed the Solo around exceptional components that deliver the warm and detailed sound that’s synonymous with vinyl, all without distorting the signal from your moving magnet cartridge. The switch mode power supply improves performance by switching outside of audible frequency to drastically reduce hum and new circuit board layout uses surface-mount components to reduce noise. If some records in your collection are a little worse for wear, the subsonic filter will help to eliminate low frequency rumbles that can be caused by imperfections within your vinyl. Combine this with the balance control for handling potential cartridge imbalances in your record player (that can cause a difference between the left and right channels) and the result is a detailed experience with accurate soundstage. The Solo phono preamplifier is green at heart with less than half a watt standby power consumption and auto power down feature if the unit isn’t used after a 20 minute period. This in turn gives the unit the same worldwide voltage for compatibility wherever you are in the world. Specifications: MAX POWER CONSUMPTION: 10W GAIN @ 1KHZ: 39dB NOMINAL OUTPUT: 300mV SENSITIVITY FOR NOMINAL OUTPUT: 3.35mV EQUIVALENT INPUT NOISE (A-WEIGHTED): ~0.09uV RIAA CURVE ACCURACY: +/- 0.65dB 30Hz-20kHz SIGNAL TO NOISE RATIO GROUNDED INPUTS REF. 1V OUTPUT (20HZ-20KHZ BW): >90dB THD+N 1KHZ (20-20KHZ BW): 30dB CROSSTALK @10KHZ: >85dB DIMENSIONS (H X W X D): 48x176x132 (1.9x6.9x5.2”) WEIGHT: 0.68kg/1.5lbs

Based on 30 years of amplifier-building expertise, Huei offers MM/MC compatibility and integrates turntables to our amplifiers. Entirely conceived, engineered and manufactured in Great Britain, Huei has been carefully designed to provide turntables with the same high standards of amplification that Chord Electronics has become known for over the past 30 years. Benefitting from both Moving Magnet and Moving Coil functionality, Huei offers compatibility with a huge range of cartridges thanks to comprehensive gain and impedance-matching options; Huei’s high- and low-gain switching settings are easily accessible via front-panel controls, introducing welcome flexibility. Huei’s advanced design offers (for the first time in a Chord Electronics phono preamp) ultra-low-noise microprocessor control of its main features, including a convenient memory function. With multiple options for impedance-matching, seven-stage switchable gain and a switchable rumble filter, Huei’s design offers comprehensive compatibility. Precision-machined from solid aircraft-grade aluminium billet, Huei has a similar form factor to the company’s Qutest DAC and also offers a top-mounted viewing window into the illuminated electronics within. The design also shares the same polychromatic control spheres the company has become known for in its digital products. The illuminated front-panel spheres offer direct access to Huei’s gain and impedance settings, selection for MM/MC cartridges and access to the on-board rumble filter. Huei is a stylish, practical and high-performance solution for integrating turntables into Chord Electronics’ (and other) systems and features both unbalanced (RCA) and balanced outputs (XLR) with RCA inputs. A high-quality 12V external power supply is also supplied.   Technical Specifications: Supported cartridges: Moving magnet and moving coil Inputs: 1x Stereo unbalanced RCA input Outputs: 1x Stereo unbalanced RCA output, 1x Stereo balanced XLR output Input Impedance: Moving magnet 47,000Ω, Moving coil 100Ω – 3,700Ω, 12-step user selectable Gain Range: Moving magnet 21dB – 42dB, 8-step user selectable, Moving coil 49dB – 70dB, 8-step user selectable Input Noise: 1.1nV/Hz Max Output Voltage RMS: 20v RMS Equalisation Response: RIAA Curve Equalisation Accuracy: +/- 0.1dB Frequency Response: RIAA Curve = 12Hz to 25kHz Rumble Filter: Rausch Slope -24dB per octave below 50Hz Output Impedance: 520Ω (resistive) Input Power Supply: 12v – 100v to 240v 50/60Hz PSU Dimensions: 41mm (H) x 160mm (W), 72mm (D) Weight: 657g

The Nash is a dedicated preamplifier and phono equalizer for every cartridge model. It is provided with two phono inputs, one for low-level MC cartridges and one for medium-high level MC cartridges and MM cartridges. Its FET-input, all-discrete components circuits feature vanishingly low noise and plenty of gain, allowing for a stunning 2.5Vrms output with 5mV on MM and 170uV on MC. The passive RIAA is implemented with high precision polypropylene capacitors. MC interface paramenters (input impedance and MC pre-pre gain) are set by potentiometer from the rear panel. As well, MM interface parameters (input impedance and capacity load) are set by DIP-switches, again from the rear panel. The Nash is provided with a Bluetooth BLE interface for control and configuration. An Android (and soon iOS) app will allow user to fully control the unit and set the configuration parameters. A comprehensive, continuously updated pickups database will make configuration faster and easier. You control the Nash by the front panel encoder, using the remote control or by the dedicated Android app via Bluetooth. Operation data are displayed on a high readability OLED display. A menu allows for setting parameters like: anti-rumble filter, MM input stage gain, etc. Two auxiliary line-level inputs make the Nash a hub or switching box for analog sources, an interesting add-on when the Nash is used together with the Young MkIII, to fully exploit the latter’s only analog input. A Young MkIII-Nash-based system may have a total of four analog sources: two phono and two line-level. The Nash noise and sound performance can be further increased by replacing the stock wall adaptor with the Van Der Graaf MkII Low Noise Power Supply. Specifications : Output Voltage:2.5Vrms (MM, 5mV input, 55dB gain) Inputs:phono MC (RCA)phono MM (RCA)2 x line-level (RCA)external power supply (4-pin XLR)trigger (3.5mm jack) Outputs:equalized line-level (RCA)trigger pass-though (jack 3.5mm) MM gain:55dB60dB65dB MC pre-pre gain:3dB to 30dB Total MC gain:58dB to 95dB MC Input impedance:10 Ohms to 50 kOhms MM Input impedance:47 kOhms15 kOhms MM Input capacitance:0pF100 pF220 pF330 pFany combination of the above Signal to noise ratio:85dBA (MM, 60dB gain)78dBA (MC, 70dB gain) Output impedance:5 Ohms Trigger input voltage:5V to 12V Supply voltage:15VDC (stock adaptor input)+5VDC;+15VDC;-15VDC (external power supply input) Power Consumption:4W (operational)0.23W (standby) Size: 200x200x50mm (wxdxh) Weight:net 2kg (including ancillaries) gross 2.5kg

Our award-winning Phono Signature phono stage is lauded as one of the best at any price.Designed and Manufactured in the United Kingdom.A phono stage is one of the most critically sensitive products in hi-fi. Because the signals produced by the needle are so small, they need to be amplified many thousands of times. Consequently, the signal path has to be perfectly clear of inductive fields, each individual component has to be best in class and of the utmost quality.The rewards though, for getting it right, are legion. Phono Signature has been designed to allow up to four turntables to be permanently connected because many vinyl enthusiasts enjoy multiple turntables, arms or cartridges for different records. It is also possible to calibrate each input separately from the comfort of your armchair. Each of the four inputs can be accurately matched to the exact specification of the cartridge and the acoustic preference of the user. Adjustment is provided for MC cartridges in; gain, resistance and capacitance. In addition, a switchable warp filter is provided to maximise amplifier performance.

The LX2-LPS is Musical Fidelity&#39;s new baby. A high quality flexible MM/MC phono stage with adjustable impedance and excellent technical performance. Housed in beautifully detailed and handsome metalwork it is the epitome of understated high class elegance.We designed it for reference level listening so it is unerringly accurate and faithful to the input. Its purpose in life is to give you your music as its artists and producers intended: nothing more, and nothing less. The critical elements of a phono stage are: accurate RIAA, low noise, low distortion, and overload margin. Technical PerformanceMusical Fidelity&#39;s RIAA correction is famous for its predictable and consistent accuracy. The LX2-LPS accuracy is ±0.25dB 20Hz-20kHZ, also it extends to 45kHz so there is no overshoot ringing.This results in absolutely clear high frequencies with no intermodulation or other distracting anomalies.The noise ratio on both MM (better than 82dB) and MC (better than 72dB) is outstanding and virtually inaudible at any volume setting. That is unless you are a half deaf head-banger.But then I don&#39;t expect that MF&#39;s refinement and subtly would be quite your thing!The LX LPS distortion is vanishingly low, typically less than 0.007% across the audio band.Overload margin is exemplary. Simply put, it is virtually impossible for any real world cartridge to overload it.As we all know nothing is perfect, but the LX2-LPS gets very near. Technical Specifications:MMInput Impedance: 47 KΩInput Sensitivity: 3.0mVTotal Harmonic Distortion: 0.01%Signal to Noise Ratio: >80dBInput Overload Margin: 15dBMCInput Impedance: 100 ΩInput Sensitivity: 300μVTotal Harmonic Distortion: 0.01%Signal to Noise Ratio: >70dBInput Overload Margin: 22dBGeneralRIAA Response ±0.25dBPower Requirement 12-24V 100mA regulatedConnectionsMoving Magnet Input: 1pr RCA socketsMoving Magnet Loading: 1pr RCA socketsMoving Coil Input: 1pr RCA socketsMoving Coil Loading: 1pr RCA socketsPower Input: DC Jack (1.3mm inner pin, outer diam. 3.5mmDimensionsLength (including terminals) 197 mmWidth 172 mmHeight (including feet) 46.5 mmWeight(Unpacked / packed): 1.05 kg/ 1.50 kgIncluded accessoriesPower Supply

Reference class phono preamplifier with unique impedance control   This ultra low noise and distortion preamplifier is made for the audio conniosseur and offers not only breathtaking performance but is capable to adapt to virtually any phono cartridge through variable impedance control. Impedance adjustment can be done while playback! Due to use of best parts, like SSM2019 from Analog Devices as input stages and Linear Technology LT1010 as high current buffer stage, Phono Box RS delivers ultra low levels of distortion and noise. Its very low output impedance makes it insensitive to selection of interconnect cables and lenghts.  Fully passive RIAA and DECCA equalisation is selectable. Phono Box RS offers fully balanced circuitry and both XLR and RCA inputs and outputs. All in all vinyl playback will never have sounded as clear, detailed and smooth, than with this superlative phono stage!   Recommended accessoires:   The addition of linear power supply Power Box RS Phono (SRP € 499,00) adds even more depth and lets you hear all microscopic fine detail.   Features:MM & MC capable  True dual mono design  Balanced XLR & unbalanced RCA In & Outputs  Fully passive RIAA & DECCA equalisation  Unique continously variable input impedance loading,    matches every cartridge (adjustment even while playing)  RCA & XLR In & Out  Superior low noise / low distortion  Classy & elegant dip switches  DC power supply (< 1 watt standby power)  Metal casing protects against vibration and interference  Faceplate silver or black  

Reference class phono preamplifier with unique impedance control   This ultra low noise and distortion preamplifier is made for the audio conniosseur and offers not only breathtaking performance but is capable to adapt to virtually any phono cartridge through variable impedance control. Impedance adjustment can be done while playback! Due to use of best parts, like SSM2019 from Analog Devices as input stages and Linear Technology LT1010 as high current buffer stage, Phono Box RS delivers ultra low levels of distortion and noise. Its very low output impedance makes it insensitive to selection of interconnect cables and lenghts.  Fully passive RIAA and DECCA equalisation is selectable. Phono Box RS offers fully balanced circuitry and both XLR and RCA inputs and outputs. All in all vinyl playback will never have sounded as clear, detailed and smooth, than with this superlative phono stage!   Recommended accessoires:   The addition of linear power supply Power Box RS Phono (SRP € 499,00) adds even more depth and lets you hear all microscopic fine detail.   Features:MM & MC capable  True dual mono design  Balanced XLR & unbalanced RCA In & Outputs  Fully passive RIAA & DECCA equalisation  Unique continously variable input impedance loading,    matches every cartridge (adjustment even while playing)  RCA & XLR In & Out  Superior low noise / low distortion  Classy & elegant dip switches  DC power supply (< 1 watt standby power)  Metal casing protects against vibration and interference  Faceplate silver or black  

Both Microsoft® Windows® and Apple® Mac OS® come with very simple audio recording software pre-installed. However, to take full advantage of the high-resolution recording facilities offered by the MM 008 ADC, we recommend recording software that can record at 24 bits/96 kHz and save lossless high-resolution audio files such as FLAC or Apple® Lossless. Specifications:Mode: MM/MC (switchable)Gain at 1 kHz: 40 dB (MM)/60 dB (MC)Input impedance (MM): 47 kΩ + 220 pF fixedInput impedance (MC): 47 kΩ + 1 nF (modifiable with external load plugs)Frequency response (flat): 20 Hz - 20 kHz ±0.3 dBFrequency response (-3 dB): 10 Hz - 50 kHzRIAA curve accuracy: ±0.3 dBTHD+N: 72 dB (MC)Crosstalk: ≧40 dBInput sensitivity (MM): 3.29 mVrms for -10 dBV output (316 mVrms)Input sensitivity (MC): 0.325 mVrms for -10 dBV output (316 mVrms)Max. output voltage: 482 mVrms at 5 mVrms input (1 kHz)Output impedance: 47 ΩInput connections: 3 pairs of RCA sockets (left/right)Output connections: 1 pair of RCA sockets (left/right)Power supply: 24 V DCPower consumption: 3.4 W/15 mAWeight: 504 g (not including power supply)Dimensions:  (W x H x D): 150 x 50 x 117 mm

Thorens MM  002 moving-magnet phono preamplifier.Specification:Mode: Moving Magnet (MM)Gain at 1 kHz: 40 dBCartridge matching (input impedance): 47 kOhms + 220 pF fixedFrequency response: 10 Hz - 50 kHz (-3 dB)RIAA curve accuracy: ±0.3 dB max.THD+N: 86 dBCrosstalk: ≧40 dBInput sensitivity: 3.14 mVrms for -10 dBV output (316 mVrms)Max. output voltage: 498 mVrms at 5 mVrms input (1 kHz)Output impedance: 47 OhmsInput connections: 1 pair of RCA sockets (left/right)Output connections: 1 pair of RCA sockets (left/right)Power supply: 24 V DC / 630 mAPower consumption: 3.3 W / 15 mAWeight: 292 g (not including power supply)Dimensions (W x H x D): 100 x 45 x 93 mm 

The MM 008 ADC is equipped with a high-resolution analogue-to-digital converter allowing you to record vinyl tracks directly onto your computer’s hard disk. It will work both with Microsoft® Windows® and Apple® Mac OS® based computerBoth Microsoft® Windows® and Apple® Mac OS® come with very simple audio recording software pre-installed. However, to take full advantage of the high-resolution recording facilities offered by the MM 008 ADC, we recommend recording software that can record at 24 bits/96 kHz and save lossless high-resolution audio files such as FLAC or Apple® Lossless. Specification:Mode: MM/MC (switchable)Gain at 1 kHz: 40 dB (MM)/60 dB (MC)Input impedance (MM): 47 kΩ + 220 pF fixedInput impedance (MC): 47 kΩ + 1 nF (modifiable with external load plugs)Frequency response (flat): 20 Hz - 20 kHz ±0.3 dBFrequency response (-3 dB): 10 Hz - 50 kHzRIAA curve accuracy: ±0.3 dBTHD+N: 72 dB (MC)Crosstalk: ≧40 dBInput sensitivity (MM): 3.29 mVrms for -10 dBV output (316 mVrms)Input sensitivity (MC): 0.325 mVrms for -10 dBV output (316 mVrms)Max. output voltage: 482 mVrms at 5 mVrms input (1 kHz)Output impedance: 47 ΩInput connections: 3 pairs of RCA sockets (left/right)Output connections: 1 pair of RCA sockets (left/right)Power supply: 24 V DCPower consumption: 3.5 W/15 mAWeight: 511 g (not including power supply)Dimensions (W x H x D): 150 x 50 x 117 mmA/D converter: Tenor TE7022L 24Bit Delta SigmaSampling rates: 8,16, 32, 44.1, 48, 96 kHzUSB output: USB 2.0, fully backward-compatible with USB 1.1Operating systems: Windows® 8, Windows® 7, Vista, XP, Mac OS®