Turntables Arms

An internally damped precision tonearm of highly polished stainless steel provides sparkling uncoloured reproduction offering pivot-stylus dimensions covering virtually all turntable requirements. The M2 Series tonearm is available in 9, 10 & 12 inch versions and offers at reasonable cost, meticulous build quality with all the most important features including lightweight stainless steel tonearm, detachable magnesium headshell with azimuth adjustment, tungsten balance weight, superb quality ball race bearings and a level of stiffness and rigidity to suit all types of cartridge. These precision made tonearms embody well tried SME principles and are suited to a broad range of cartridges including those of medium and low compliance. The headshell is pressure die-cast in magnesium for lightness and rigidity. A collet of ingenious design affords ‘one-piece’ rigidity and allows azimuth correction to be made before final tighteningBuildThe M2-9 shell is pressure die-cast in magnesium for lightness and rigidity. Series M2-9 is the standard arm having a pivot-stylus dimension of 233.2 mm (9.18”) and will therefore be the one most frequently used. Series M2-10 is identical except that the pivot-stylus dimension is 239.3 mm (9.42”) a difference that suits the layout of some decks. Series M2-12 has a pivot-stylus dimension of 308.8 mm (12.16”). Distortion caused by lateral tracking error is at least 25% less than possible with a nine or inch arm. However effective mass will be typically 12.0 grams. Also, a turntable designed for 12-inch arms must be selected.DampingThe internally damped tonearm of highly polished stainless steel provides sparkling uncoloured reproduction. A unique single element balance system caters for cartridges weighing 5 to 12 grams. After balancing tracking force is applied by forward movement of the weight ensuring the lowest system inertia. The weight moves on a precision screw thread with backlash eliminator allowing exact setting of vertical tracking force.AdjustmentsA collet of ingenious design affords ‘one-piece’ rigidity and allows azimuth correction to be made before final tightening. 1.0 gram per revolution tungsten weight sub-graduated 0.25 and 0.025 gram moving on a precision screw with backlash eliminator.
220mm (48”) D501 balanced audio lead. Engineered in the best camera quality with satin chrome finish Fluid damped lift/lower control.
Low friction, fully shielded races for both axes.
Sliding base for tracking adjustment.
Thumbwheel height adjustment.
Traditional pattern anti-skate. 

As a member of the M2 family this tonearm is built by enthusiasts for enthusiasts and among its extensive features include, vertical and horizontal tracking adjustment, tungsten balance weights housed in satin chromed brass sleeves. Double draw-pin detachable headshell with azimuth adjustment and height adjustment by thumb wheel enabling its use with wide range of both cartridges and turntables.BuildS2-R Aluminium shell detachable and interchangeable without disturbing cartridge or wiring. Double draw-in pin bayonet fitting design ensures a rigid junction with the tone-arm. Stainless steel ground horizontal spindle carried in substantial yoke in lOmm diameter precision ball race bearings. Stainless steel ground vertical spindle with integral 16mm diameter flange to couple the spindle with the yoke. The 23mm diameter steel pillar is heat treated, ground, internally honed and carries two 17mm diameter precision ball race bearings widely spaced to resist tilt. Internal wiring is Silver Litz.DampingInternal constrained layer damps minute residual vibrations making the tone-arm acoustically inert.AdjustmentsUnique headshell to tone-arm coupling readily allows cartridge azimuth adjustment. The Anti-Skate control operates through an Anti-Skate weight and filament and is adjustable for up to 5g of cartridge vertical tracking force (VTF). The lowering/raising control gives a smooth positive action and allows for the lifting height of the cartridge above the record to be adjusted. Tungsten-alloy balance weight inserts allow for maximum centre of gravity shift to balance a greater range of cartridges. Up to 38g in S2-R headshell and direct plug-in heads up to 46g. Precise vertical tracking force up to 5g is applied in 0.5 increments via the rider weight and graduated wayrod. Thumbwheel cartridge vertical tracking angle (VTA), height adjustment. Bedplate affords +/- 12.0mm movement to facilitate horizontal tracking angle (HTA) adjustment.

Βραχίονας Static 9'' Resonance optimaizedΠροδιαγραφές:  Effective mass without headshell 3.5 gMass of supplied headshell 15.5 gEffective armlength (distance between the stylus and pivot point): 231.0 mmMounting distance (distance between the pivot point and turntable center): 213.0 mmOffset angle: 23.9 degreesOverhang: 18.0 mmTracking force adjusting range (direct reading): 0-3 gHeight adjustment range: 35-55 mmDiameter of the armbase mounting hole: 19-20 mmDiameter of the center shaft of tonearm: 18.0 mmInner null point: 66 mmOuter null point: 120.9 mmCounterweight for cartridge + headshell mass between 21 and 28 g includedHeadshell LH-2000E included Headshell LH-2000E weight: 15.5 gTA-110 total weight including headshell: 470 gSet of tonearm cables 6NX-TSW-1010 includedExtra mass ring for heavier cartridges included 

Precision tonearm with carbon-fibre armtube. The tonearm’s design efficiently leads parasitic vibrations away from the cartridge into the mounting board, guarantees the precise tracing of the record groove by the needle and also facilitates fine adjustment of vertical and horizontal tracing. The tonearm fits on turntables or tonearm boards with mounting hole according to Linn standardFeaturesThe headshell and armtube are fashioned from a single piece of carbon-fibre.Conical armtube avoids standing wave reflections.Inverted bearing design with four ABEC7 spec ballraces.Arm bearing housing of solid ring type. The massive outside ring is open to avoid resonances.Sorbothane® -damped counterweight effectively counteracts unwanted resonances.Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped records.Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.Straight armtube reduces toe-in error.Silicone-damped armlift can be adjusted to suit arm height.The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated phono sockets.Terminal with phono sockets and earth screw.

The legendary RB330Designed using the latest 3D CAD & CAM technology, the new RB330 is the culmination of more than 35 years of tonearm design experience. Featuring a brand new bearing housing and our latest tonearm tube designed using intelligent redistribution of mass, ensure this arm will exhibit fewer points of possible resonance.Extreme stability with almost friction free movement from the new high precision bearing assemblies guarantees to gather more information from your vinyl than ever before. Featuring a new bias assembly, re-designed stiffer vertical bearing housing, integrated arm clip and an improved spring housing with easier to read numbers. Rega made, new low capacitance phono cable with Neutrik plugs. Improved lower friction, precision horizontal and vertical bearings.Rega is famed for its tonearm designs. One unique characteristic of these designs is the achievement of near frictionless movement horizontally and vertically whilst having no measurable free play in the bearing assemblies (and in reality one or two microns of pre load). So, why has Rega spent over thirty years and invested so heavily in this area of tonearm design where the removal of even microns of movement has been pursued?

The Nostatic Arm is the modern version of the formerly well known “Dust Bug” by Cecil   Watts. The Nostatic arm incorporates a carbon fiber brush that removes the static electricity from the record during playback, and at the same time picks up the loose dust before the stylus reaches that part of the record. The Nostatic arm has an earth wire which is connected to the earth of the record player or the amplifier. The height can be easily adjusted to fit most record players. It also has a sliding weight in order to adjust the “dusting force” of the brush. Finally the base of the brush has sticky tape so if preferred it can be stuck to the surface of the record player for easy use.

DescriptionThe TecnoArm “A” is a fundamental mechanical rebuild of the well-known RB202 tonearm, to which is added monolithic wiring of the highest quality.Please Note: This tonearm does not come with a cartridge.The arm tube is bead-blasted and perforated, which disperses structural resonances and yields a lower effective mass. The arm wand is internally damped to reduce resonance further, and the headshell is machined flat, to allow true azimuth relative to the bearing cradle. After modification the bearings are re-adjusted for highest possible performance, according to original Rega procedures.

DescriptionThe TecnoArm “A” is a fundamental mechanical rebuild of the well-known RB202 tonearm, to which is added monolithic wiring of the highest quality.Please Note: This tonearm does not come with a cartridge.The arm tube is bead-blasted and perforated, which disperses structural resonances and yields a lower effective mass. The arm wand is internally damped to reduce resonance further, and the headshell is machined flat, to allow true azimuth relative to the bearing cradle. After modification the bearings are re-adjusted for highest possible performance, according to original Rega procedures.

As a member of the M2 family this tonearm is built by enthusiasts for enthusiasts and among its extensive features include, vertical and horizontal tracking adjustment, tungsten balance weights housed in satin chromed brass sleeves. Double draw-pin detachable headshell with azimuth adjustment and height adjustment by thumb wheel enabling its use with wide range of both cartridges and turntables.BuildS2-R Aluminium shell detachable and interchangeable without disturbing cartridge or wiring. Double draw-in pin bayonet fitting design ensures a rigid junction with the tone-arm. Stainless steel ground horizontal spindle carried in substantial yoke in lOmm diameter precision ball race bearings. Stainless steel ground vertical spindle with integral 16mm diameter flange to couple the spindle with the yoke. The 23mm diameter steel pillar is heat treated, ground, internally honed and carries two 17mm diameter precision ball race bearings widely spaced to resist tilt. Internal wiring is Silver Litz.DampingInternal constrained layer damps minute residual vibrations making the tone-arm acoustically inert.AdjustmentsUnique headshell to tone-arm coupling readily allows cartridge azimuth adjustment. The Anti-Skate control operates through an Anti-Skate weight and filament and is adjustable for up to 5g of cartridge vertical tracking force (VTF). The lowering/raising control gives a smooth positive action and allows for the lifting height of the cartridge above the record to be adjusted. Tungsten-alloy balance weight inserts allow for maximum centre of gravity shift to balance a greater range of cartridges. Up to 38g in S2-R headshell and direct plug-in heads up to 46g. Precise vertical tracking force up to 5g is applied in 0.5 increments via the rider weight and graduated wayrod. Thumbwheel cartridge vertical tracking angle (VTA), height adjustment. Bedplate affords +/- 12.0mm movement to facilitate horizontal tracking angle (HTA) adjustment.

An internally damped precision tonearm of highly polished stainless steel provides sparkling uncoloured reproduction offering pivot-stylus dimensions covering virtually all turntable requirements. The M2 Series tonearm is available in 9, 10 & 12 inch versions and offers at reasonable cost, meticulous build quality with all the most important features including lightweight stainless steel tonearm, detachable magnesium headshell with azimuth adjustment, tungsten balance weight, superb quality ball race bearings and a level of stiffness and rigidity to suit all types of cartridge. These precision made tonearms embody well tried SME principles and are suited to a broad range of cartridges including those of medium and low compliance. The headshell is pressure die-cast in magnesium for lightness and rigidity. A collet of ingenious design affords ‘one-piece’ rigidity and allows azimuth correction to be made before final tighteningBuildThe M2-9 shell is pressure die-cast in magnesium for lightness and rigidity. Series M2-9 is the standard arm having a pivot-stylus dimension of 233.2 mm (9.18”) and will therefore be the one most frequently used. Series M2-10 is identical except that the pivot-stylus dimension is 239.3 mm (9.42”) a difference that suits the layout of some decks. Series M2-12 has a pivot-stylus dimension of 308.8 mm (12.16”). Distortion caused by lateral tracking error is at least 25% less than possible with a nine or inch arm. However effective mass will be typically 12.0 grams. Also, a turntable designed for 12-inch arms must be selected.DampingThe internally damped tonearm of highly polished stainless steel provides sparkling uncoloured reproduction. A unique single element balance system caters for cartridges weighing 5 to 12 grams. After balancing tracking force is applied by forward movement of the weight ensuring the lowest system inertia. The weight moves on a precision screw thread with backlash eliminator allowing exact setting of vertical tracking force.AdjustmentsA collet of ingenious design affords ‘one-piece’ rigidity and allows azimuth correction to be made before final tightening. 1.0 gram per revolution tungsten weight sub-graduated 0.25 and 0.025 gram moving on a precision screw with backlash eliminator.
220mm (48”) D501 balanced audio lead. Engineered in the best camera quality with satin chrome finish Fluid damped lift/lower control.
Low friction, fully shielded races for both axes.
Sliding base for tracking adjustment.
Thumbwheel height adjustment.
Traditional pattern anti-skate. 

Precision tonearm with carbon-fibre armtube. The tonearm’s design efficiently leads parasitic vibrations away from the cartridge into the mounting board, guarantees the precise tracing of the record groove by the needle and also facilitates fine adjustment of vertical and horizontal tracing. The tonearm fits on turntables or tonearm boards with mounting hole according to Linn standardFeaturesThe headshell and armtube are fashioned from a single piece of carbon-fibre.Conical armtube avoids standing wave reflections.Inverted bearing design with four ABEC7 spec ballraces.Arm bearing housing of solid ring type. The massive outside ring is open to avoid resonances.Sorbothane® -damped counterweight effectively counteracts unwanted resonances.Counterweight shaft lowered to record level reduces cantilever forces and dynamic wow when playing warped records.Solid armbase permits accurate height adjustment of armtube and VTA (vertical tracing angle).Single-screw fixing of armtube allows rotation for easy adjustment of needle azimuth despite fixed headshell.Straight armtube reduces toe-in error.Silicone-damped armlift can be adjusted to suit arm height.The internal wiring consists of flexible high-purity copper from the headshell right through to the gold-plated phono sockets.Terminal with phono sockets and earth screw.

The RB3000 tonearm is packed with new features pushing the boundaries of tonearm design. As with all Rega tonearms, each one is meticulously hand-built by a team of highly skilled technicians. The R3000 uses improved bearings with each one being hand selected to be an interference fit with the paired spindle matching both the inside and outside diameters. This is a Rega developed method of increasing the amount of detail retrieved from the record surface, designed specifically to maximise performance of the tonearm and cartridge (cartridge sold separately).Advanced design, precision engineeringThe entire tonearm structure is designed to have the minimum of mechanical joints whilst using the stiffest materials in all critical areas. The tolerance of the RB3000 tonearm is so tight that no adhesive is used at any point throughout the construction. A brand new, low mass, precision engineered, vertical bearing assembly has been manufactured to further complement the inherent design philosophy of the Planar 10 turntable.The RB3000 uses the latest award-winning Rega arm tube. Each one which is meticulously hand polished (keeping mass to an absolute minimum) and has been completely redesigned to redistribute mass and further reduce stresses and resonances. This advanced design tube increases the stiffness and rigidity of the overall assembly whilst reducing stress on the bearings even further.

Designed using the latest 3D CAD & CAM technology, the new RB880 is the culmination of almost 40 years of tonearm design experience. This tonearm features a new aluminium vertical bearing housing, a redesigned sleeve and vertical bearing shaft (both manufactured from stainless steel) to improve mounting stability and overall rigidity. The advanced tonearm tube is designed using intelligent redistribution of mass, ensuring this arm will exhibit fewer points of possible resonance.Fine tuning an iconThe extreme levels of stability achieved, coupled with almost friction free movement from the high precision hand matched bearing assemblies, guarantee to gather more information from your vinyl than ever before. You will also find a Rega made new low capacitance phono cables terminated with high specification phono plugs.Rega is famed for its tonearm designs. One unique characteristic of these designs is the achievement of near frictionless movement horizontally and vertically whilst having no measurable free play in the bearing assemblies. A brand new low mass precision engineered vertical bearing assembly has been manufactured to further complement the inherent design philosophy of the Planar 8 turntable. The RB880 uses the latest Rega arm tube. Completely redesigned to redistribute mass and further reduce stresses and resonances. This advanced design tube increases the stiffness and rigidity of the overall assembly using CAD design to blend the multiple varying tapers.Externally we have fitted a bespoke Rega designed low capacitance phono cable. Which uses an advanced phono plug assembly. This has only two parts to minimise joints and incorporates a twist and clamp design locking the plug to the terminal. The design increases connectivity and ensures the signal path is kept as clean as possible.

This REGA RB 202 tonearm is the heir to the famous RB 250 and 251 featured on the Planar 2 and P2 series. The care dedicated to the new vertical and horizontal ball bearings results in minimum friction during displacement along its axis and hence minimising playback errors. It is the first in the range to use a tube built out of a single piece of pressure cast alloy. This element, identical to the RB 303, gives it great rigidity, low resonance and great groove tracking precision. Like on the legendary RB1000, it is secured to the turntable by three points for amazing mechanical stability.This tonearm is very efficient and, like all Rega products, highly musical. It is naturally possible to pair it with the manufacturer's cartridges like the Bias, Elys or Exact, though it is multipurpose and works very well with many moving coil and magnet cartridges. Yet another job well done on the manufacturer's record and certainly a benchmark for its price… In any case, we don't know of any serious competition in this range, except its elder brother the RB303!

Βραχίονας Static 12'' Resonance optimaizedΠροδιαγραφές:  Effective mass without headshell: 5 gEffective armlength (distance between the stylus and pivot point): 329.0 mmMounting distance (distance between the pivot point and turntable center): 316.6 mmOffset angle: 16.5 degreesOverhang: 12.4 mmTracking force adjusting range (direct reading): 0-3/0-4 gHeight adjustment range: 35-55 mmDiameter of the armbase mounting hole: 19-20 mmDiameter of the center shaft of tonearm: 18.0 mmInner null point: 66 mmOuter null point: 120.9 mmCounterweight for cartridge + headshell mass between 21 and 28g includedHeadshell LH-2000E included Headshell weight: 15.5 gTA-210 total weight including headshell: 536 gSet of tonearm cables 6NX-TSW-1010 includedExtra mass ring for heavier cartridges included

Βραχίονας Static 12''Προδιαγραφές:  Effective length (distance between the stylus and pivot point): 329mmMounting distance between the pivot point and turntable center: 314mmOffset angle: 19 degreesOverhang: 15mmTracking force adjusting range ( direct reading): 0 to 3gHeight adjustment range: 35mm to 55mmDiameter of the armbase mounting hole: 19mm to 20mmDiameter of center shaft: 18mm

Βραχίονας Dynamic 12''Προδιαγραφές: Effective length (distance between the stylus and pivot point): 329mmMounting distance between the pivot point and turntable center: 314mmOffset angle: 19 degreesOverhang: 15mmTracking force adjusting range (direct reading): 0 - 5 g Height adjustment range: 42 mm - 57 mmDiameter of  the armbase mounting hole: 34 mm - 36 mmDiameter of the center shaft: 16 mmFixing holes PCD: dia. 50 mmSize/Thread: dia. 3.2 mm (dia. 3mm x 20mm and dia. 3 mm wood screw)Digital scale DS 1 includedHeadshell SH-1 included